Yellobrik ORX 1802-2 LC User manual

yellobrik
®
Quick
Reference
ORX 1802 (LC,ST,SC,MM)
3Gbit Fiber Optic to SDI Receiver
SDI Video
Output 1
Receiving
Data
DC Power Input
Power
Connected
SDI Video
Output 2
LC
Singlemode
ST
Singlemode
SC
Singlemode
LC
Multimode
Fiber Input - Four options are available
LYNXTechnik AG
WARNING
Class 1M Laser Product
Laser Radiation
Do not view directly with
optical instruments

LC
Singlemode
ST
Singlemode
SC
Singlemode
LC
Multimode
Connections
The SDI video outputs are connected to the corresponding 75 Ohm BNC
connections provided. The ber connection is made to the ber SFP sub module
as indicated on the module.
Four versions of the module are available, the only dierence is the SFP sub module
installed into the basic module.
ORX 1802-2 LC - Singlemode LC ber connection
ORX 1802 ST - Singlemode ST ber connection
ORX 1802 SC - Singlemode SC ber connection
ORX 1802 MM - Multimode LC ber connection
Operation
Operation of the ORX 1802 is fully automatic.The SDI video format is automatically
detected, reclocked and provided on two SDI output connections. The module
supports all SDI video standards as well as DVB/ASI.
The ORX 1802 supports hot swapping and hot plugging of
connections.
No user settings are provided for this module.
The module ber connection is supplied with a rubber plug installed, this is to
prevent dust contamination. Please retain the plug and use if the cable is ever
disconnected from the module.
Power
The module requires a 12V DC power input and the LED conrms when power
is connected. A power supply is provided, however if you use your own power
supply, please provide a clean power source between 7 and 24VDC.
The OTX 1410 has a power consumption of approximately 2.2W nominal.

Power Lead Strain Relief
The module has a small hole in the case which is located above the power
connection. This prevents the power lead from being accidentally pulled out. Use
the supplied tie-wrap and secure the lead, as shown below.
Optional Mounting Solutions
The optional RFR 1001 mounting bracket can be used to permanently mount the
module on any surface or on 19” rack rails.
The optional RFR 1000-1 rack mount can be used to mount up to 14 yellobrik
modules permanently. In addition, the RFR 1000-1 can provide full power
redundancy for all mounted yellobriks.

yellobrik
®
LYNX
Technik
AG
| Broadcast Television Equipment
Technical Specications
Optical Input
Singlemode
1 x ber optic Input
LC, ST or SC connection
SMPTE 297M - 2006
Input range (wavelength) 1260nm to 1620nm
RX sensitivity -3dBm to -19dBm
Optical Input
Multimode
1 x Fiber Optic Input
LC Connection
SMPTE 297M - 2006
Input range (wavelength) 780nm to 880nm
RX sensitivity 0dBm to -15dBm
SDI Output 2 x SDI video on 75 Ohm BNC connectors
SMPTE 424M, SMPTE 292M, SMPTE 259M, DVB-ASI
Multi-standard operation from 270Mbit/s to 3Gbit/s
Return Loss: >15dB from 5MHz to 1.5GHz
>10dB from 1.5GHz to 3GHz
Power +12VDC power supply (included)
Supports external power input from 7 - 16 VDC
Power LED on side of module. Power Consumption 1.3W
Visit our website for information and product updates.
www.lynx-technik.com