YESOUL M1 User manual

M1
YESOUL BIKE
Product model: YS-002
Before using this product,
carefully read and
properly keep this manual.
YESOUL BIKE
M1 Product Manual

YESOUL BIKE M1
Product Parameters
Tablet (mobile phone) holder size
Supporting software version
Resistance system
Drive mode
Power supply
Sensing system connection
Height limit
Rated maximum load
Net weight
Gross weight
Overall dimensions
Maximum tablet width: 260mm
iOS 10.0 or higher, Android 5.0 or higher
Magnetron resistance system
Belt drive
Button battery (model: CR2477)
Bluetooth
150-195cm
120kg
33kg
36kg
(length) 1000mm × (width) 510mm× height 1250 mm

Important Safety Instructions
Please read them carefully. Improper use may result in
personal injury or death!
1. Make sure that the saddle height adjustment knob is secured correctly, and will not affect motion
during exercise.
2. Keep children and pets away from this product. This product is for those over 16 years old only.
3. Never stretch any object or body part into the openings of the bike.
4. The weight of the user must not exceed the maximum load.
5. Get off the bike until flywheel and pedals stop rotating. Otherwise, severe injuries may be caused
due to control failure.
6. If you feel any discomfort, such as dizziness or breathing difficulty, stop riding the bike and
carefully get off.
7. Never turn pedals by hand or touch any rotating mechanical part; otherwise, personal injury may
be caused.
8. Keep the body hydrated as needed during riding.
9. Use this product according to the instructions in this manual. Warm up fully before exercise.
10. Without the preliminary determination of baseline fitness level and medical certificate signed by
a doctor, never be engaged in high-speed or high-intensity sports. Before attempting any high-in-
tensity short sprints, pay attention to the body state and posture, and apply a controllable speed.
11. Wear professional cycling clothes or tight-fitting sportswear and sports shoes, and tighten foot
straps to avoid injury caused by pulling or entanglement by this product.
12. Never use this product with inappropriate shoes or barefoot.
13. Incorrect or excessive training may cause injury.
14. Check whether the bike for loosening or damage before each use.
15. Never refit this bike or use non-original accessories without permission. The casing must be
opened by professionals, in order to avoid damage.
16. Those pregnant or with high blood pressure, heart disease, lumbar spondylosis or reduced
mobility must not use this product without the permission of doctors.
17. In case of any discomfort such as dizziness or chest pain during exercise, stop exercising
immediately and go to a hospital for examination.
18. If the product fails, immediately stop using it.
19. This product must not be used for medical rehabilitation.
20. Use this product on a flat and clean ground.
21. Carry out preventive maintenance regularly.
22. Never expose this product in a humid place. This product must not be used outdoor or in any
humid place.

L-type cross head hex wrench
4×hexagon socket cap
screw M6×12
4×hexagon socket button head
screw M8×45
4× flat gasket
2×hexagon socket cap screw
M6×12
2 × Spring washer
2× hexagon socket cap screw
M6×12
Hexagon socket cap screw M6×35
Hex wrench
Open-ended wrench
NameNO. NO. Name
Frame Mobile phone (tablet) holder
Front tube Bottle holder
Handlebar cover
Ziplock bag (manual, tools)
Rear tube
Pedal (left: L; right: R)
Handlebar
Dual-purpose bracket
List of Parts
Installation Guide --------- List of Parts
Manual
STEP1: Check of parts

Installation Guide - List of Parts
Accessories List (Tools List)
L-type cross head
hex wrench
Hex wrench
Hexagon socket
cap screw M6X35
Open-ended
wrench
NO. Name Quantity Picture
A
B
C
D
1
1
35
1

STEP 2: Installation of bottom tube
3. Align the hole of the front and rear tubes with the bottom holes of the frame①, manually screw the
front and rear tubes into frame, and tighten it via the L-type cross head hex wrench (A)
Installation Guide
Washer
1. Take L-type cross head hex wrench (A) out of the ziplock bag.
2. Remove four screws (M8×45) and washers of the front tube ② and rear tube ③ via the wrench.

3. Insert the bottle holder ⑧ along the slot into the dual-purpose bracket. Align the hole of the
bottle holder with that of the bracket ⑥, manually install two screws (M6×12) into holes, and
tighten them via the hex wrench (B).
Installation Guide
STEP 3: Installation of bottle holder
1. Take the hex wrench (B) out of the ziplock bag.
2. Remove two screws (M6×12) of the dual-purpose bracket ⑥ via the wrench.

2. Align the holes of the handlebar ⑤ with those of the riser, manually install screws into two rear
holes (without tightening), and insert the dual-purpose bracket ⑥ into the round hole of the
handlebar ⑤ as indicated by the arrow. Then manually install the other two screws and one long
hexagon socket cap screw (C, in the ziplock bag) into three corresponding holes (without tighten-
ing). Finally, vertically tighten five screws down via the hex wrench (B), and press down the
decorative cover ⑨ of the handlebar. Thus, the handlebar installation is completed.
First install two screws here
Hexagon socket cap screw
(C, in the ziplock bag)
Installation Guide
STEP 4: Installation of handlebar and dual-purpose bracket
1. Remove four screws (M6×12) of the riser via the hex wrench (B).

2. Align the holes of the tablet holder ⑦ with those of the dual-purpose bracket ⑥, manually install
screws (M6×12) and tighten them via the hex wrench (B).
Spring washer
Installation Guide
STEP 5: Installation of tablet (mobile phone) holder
1. Remove two screws (M6×12) and elastic washers of the dual-purpose bracket ⑥ via the hex
wrench (B).

STEP 6: Pedal installation
1. Take out the pedal assemblies L and R④.
2. Separate the pedal assemblies L and R④.
3. Lock the pedal assembly L④ into the left crank, and tighten with the box-ended
wrench (D) along the direction indicated by the arrow.
4. Lock the pedal assembly R④ into the right crank, and tighten with the
box-ended wrench (D) along the direction indicated by the arrow.
Open-ended wrench(D)
Safety tips:
Reverse riding is not recommended, as it is likely to loosen pedals. After
reverse riding, check whether the pedals are locked, in order to avoid
safety issues arising from loose pedals.。
Installation Guide
Pedal
assembly R④
Pedal
assembly L④
Screw the pedal into the crank manually
first, and then tighten the pedal assemblies
L and R ④with the box-ended wrench (D).
(Note: The tightening directions for both
the left pedal and the right pedal are
towards the head direction.)

Tip: If the resistance change is inconsistent with the resistance change in APP after the
resistant knob is turned, press the buttons A and B to correct it.
STEP 7: Battery Dismantling and Installation
Installation Guide
1. If the bike is provided with a battery, pull the insulation strip out of the gap of the battery cover
before using this product;
2. Battery replacement: Remove ST4×13 cross head tapping screws of the battery cover via the
L-type cross head hex wrench (A), open the battery cover, take out the old battery, and insert a
new battery into the battery slot, with its positive pole outward (“+” outward).

+
-
Statement:
This manual contains the functional introduction and operating instructions as much as possible
when printed.
With the continuous improvement of hardware and software and optimization of design, this
manual may be inconsistent with the purchased product.
In case of any discrepancy in appearance, interface and color, the actual product shall prevail.
Lockable pulley
Rear column tightening knob
(Adjust the saddle height)
Saddle tightening knob
(Adjust the saddle
horizontally)
Saddle tightening knob
(Adjust the saddle
horizontally)
Front column tightening knob
(Adjust the head height)
Low
High
Body level adjustment pad
Resistance knob
(Adjust the resistance as needed;
press it to brake in an emergency.)
Safety tip:
Adjust the bike and tighten the body tightening knob as needed before using it.
Installation Guide (for reference only, subject to the actual product)

Due to software upgrades, the actual product will prevail.
Scan the QR code to download
YESOUL APP
Android/iOS mobile client
APP installation and registration
1. Scan the QR code to download the APP, and register an APP account.
2. Upon registration, open the spinning bike course in the APP. Please connect the spinning bike
according to the interface prompts in the course for the first use. Then, once you ride the spinning
bike, the exercise mode of the APP will be enabled or the course will be automatically accessible.
3. Before connecting the APP with spinning bike, make sure that the Bluetooth of your mobile
phone/tablet PC has been enabled and no other devices are connected.
About APP membership
Registered users can get the membership free of charge on the product membership page as
indicated on the interface.
· After the first connection, the APP will automatically match the bike. Directly
ride the bike when it is used for the second time.
· The bike does not support the simultaneous connection of multiple mobile
phones. Before using this product, make sure that other users are not connected to
the bike.
·The bike will be disconnected 10 min after riding.
·In addition to connection with YESOUL APP, the Bluetooth can also be connected
with kinomap and zwift software.
First Use

Pull
Handlebar height
adjustment
Tight
Loose
Pull
Handlebar height
adjustment
Tight
Loose
1 、Handlebar height adjustment:
How to Adjust Bike
Loosen and pull out the front column knob with one hand, hold the middle part of the handlebar
with the other hand, and lift the handlebar to the desired position. Then release the knob, and
gently pull the column up and down until the spring is automatically reset (when a “click” sound is
heard, it means that the knob has been clamped in the hole of the column). Tighten the knob as
much as possible.
2 、Saddle height adjustment:
Loosen and pull out the rear column knob with one hand, and lift (or press) the saddle with the
other hand to the desired position. Loosen the knob and gently pull the column up and down until
the spring is automatically reset (when a “click” sound is heard, it means that the knob has been
clamped in the hole of the column). Tighten the knob as much as possible.

There are four adjustment pads at the bottom of the front and rear pedal tubes. Screw these pads
until they are tightly secured on the floor and the body does not shake.
Loose
Tight
Horizontal
adjustment
of saddle
How to Adjust Bike
3. Horizontal adjustment of saddle:
Loosen the knob under the saddle, slide the saddle back and forth to the desired position, and
tighten the knob as much as possible.
4. Body level adjustment:
High
Low
Low

How to Determine Correct Riding Posture
(Fig. 1) (Fig. 2)
Leg
straight
1、Setup of correct saddle position
Saddle height
Put the feet together, stand on one side of the saddle and adjust the saddle to the hip height (Fig.
1). Then site on the saddle, and step on the pedals forcibly until they are stopped at 6 o’clock and
the leg can be fully stretched (Fig. 2).
3 o’clock: the right
crank is parallel to floor
in the right directio
(Fig. 3)
Horizontal position of saddle
Put the right foot into the clamp, and step on the pedals, until the right pedal is at 3 o’clock and
the front side of the knee joint is on the same vertical line as the pedal, that is, the saddle is in the
correct position (Fig. 3).
Hip
joint

(Fig. 1) (Fig. 2)
2. Setup of appropriate handlebar height
Each user can set up the appropriate handlebar height based on his or her body height and riding
experience.
Recommendation: The handlebar should be slightly higher than the saddle for new users (Fig. 1)
and flush with or slightly lower than the saddle for experienced users (Fig. 2).
Users subject to lumbar muscle strain and lumbar spondylosis may ride the bike with the consent
of doctors. It is recommended to adjust the handlebar into a higher position.
1
3
2
2
1
3
Hand position 1
1
Hand position 2
2
Hand position 3
3
How to Determine Correct Riding Posture
3、Handle position layout of spinning bike
During riding, coaches will show the corresponding hand positions, i.e. the corresponding parts of
the handlebar, as shown below.

Daily use:
Keep the spinning bike on a dry, ventilated and flat floor. If not used in a long time, the bike should
be covered to keep its body clean and tidy.
Frame maintenance:
Wipe off sweat on the frame with cloth after exercise. Do not wipe the bike with wet cloth, in order
to avoid rusting.
Belt maintenance:
Check the belt pulley for cracking and deviation, and adjust or replace the belt in time. Regularly
clean the belt groove to prevent the belt from jumping out of the groove.
Inspection of body screws:
Always check the screws of all body parts for loosening or falling, and tighten or replace them in
time.
Inspection of resistance adjustment knob:
Always check the resistance adjustment knob for loosening or falling. Check whether the resistance
is reasonable, so as to calibrate resistance in time.
Inspection of pedals and cranks:
Always check the screws of pedals and cranks for loosening, and tighten them in time.
Saddle maintenance:
Always check whether the saddle is loose and tighten it in time. Wipe the saddle with cotton cloth
to keep it dry.
Routine Maintenance

Prolinx GmbH
Brehmstr.56,40239 Duesseldorf
Germany
EC
REP