YewdaleDefiant 980000 Installation manual

yewdale.co.uk
Part no: 980000
Programming Instructions
for YewdaleDefiant® motor
(980000)
Programming Instructions
for YewdaleDefiant® motors
(980000)

YewdaleDefiant® programming instructions Part no: 9800002
Power and connection:
1. Hard-wired systems:
2. Wiring illustration for Hard wired
NB.See below key symbols
Programming Instructions
YewdaleDefiant®230v AC Tubular Motor (980000)
980000
max 4 blinds
230v AC
980030 low voltage switch
with back box
980014
4 motor relay
230v AC
980000
max 1 blind
230v AC
980023 switch
with back box
240v
Fused
supply
Up/Down
Clockwise:
Increase blind travel
Anticlockwise:
Decrease blind travel
A Blue line:
Up / Down limit position
B Red line:
New position after
adjustment
Neutral
Manual Switch
Only use regulator to
adjust limit stops and
ensure the speed is
set below 30rpm
Up
Stop
Down
Down/Up
Earth
(green/yellow)
Neutral
(green)
Live
(brown)
980023
switch
with back
box
Earth
A
B

Call: [phone] Fax: [phone] Email: [email protected] Visit: www.yewdale.co.uk 3

YewdaleDefiant® programming instructions Part no: 9800004
Set UP limit positions:
1.Ensure motor has power.
2.Press UP on Manual Switch.
3.Please see following instructions:
Adjusting blind limit stops (motor on right):
NB. This motor is supplied pre-set with approximately 3 turns in either
direction. Please take care to ensure bottom bar stops before contact with
the barrel.
NB. These instructions are for a motor on the right with fabric standard rolled.
YELL OW
GREY
YELL OW
GREY
1. Adjust the GREY
knob to change
UP limit stop
position
2. Adjust the YELLOW
knob to change
DOWN limit stop
position
When UP limit stop is
above required place
When UP limit stop is
below required place
Press DOWN until
blind is at or near
required position
Press UP until blind
is at or near required
position
Rotate GREY knob until blind is at the required
position. Clockwise rotation will lower the
blind, anti-clockwise will raise the blind.
UP limit position is now set
Rotate GREY knob until blind is at the required
position. Clockwise rotation will lower the
blind, anti-clockwise with raise the blind.
UP limit position is now set
OR
Programming Instructions
YewdaleDefiant®230v AC Tubular Motor (980000)

Call: [phone] Fax: [phone] Email: [email protected] Visit: www.yewdale.co.uk 5
Set DOWN limit positions:
1.Ensure motor has power.
2.Press DOWN on Manual Switch.
3.Please see following instructions:
When DOWN limit stop
is below required place
Press UP until blind
is at or near required
position
Rotate YELLOW knob until blind is at the
required position. Clockwise rotation will lower
the blind, anti-clockwise with raise the blind.
DOWN limit position is now set
When DOWN limit stop
is above required place
Press DOWN until
blind is at or near
required position
Rotate YELLOW knob until blind is at the
required position. Clockwise rotation will lower
the blind, anti-clockwise will raise the blind.
DOWN limit position is now set
OR

YewdaleDefiant® programming instructions Part no: 9800006
Items Problems Cause Solution
1
After connecting power,
the motor doesn’t work
or works slowly
1. Connected with the wrong voltage
2. Overloading
3. Incorrect installation leading to
motor jamming
1. Change to the correct voltage
2. Choose suitable motor torque
3. Check the components
2
After connecting with
power, only one
direction works
The limit stop position has not
opened
Rotate crown 1 or 2 circles by hand on the opposite
of motor current running direction
3
The motor stops
suddenly whilst
running
1. Motor has exceeded overheating
protection +130oC
2. Power was cut o
3. Motor arrived at the limited
position
1. After the motor has cooled suciently, motor
will perform as required
2. The motor will resume once power is back on
3. Check limit stop position by adjusting knob
4Motor runs in wrong
direction Wired incorrectly Exchange the connection of black and blue wires
Adjusting blind limit stops (motor on left):
NB. The GREY & YELLOW knobs will be reversed when motor is on the left with
the fabric standard rolled. See illustrations below:
1. Adjust the GREY
knob to change
UP limit stop
position
2. Adjust the YELLOW
knob to change
DOWN limit stop
position
GREY
YELL OW
GREY
YELL OW
Programming Instructions
YewdaleDefiant®230v AC Tubular Motor (980000)
Trouble Shooting:

Call: [phone] Fax: [phone] Email: [email protected] Visit: www.yewdale.co.uk 7

Yewdale, Enterprise Way,
Wickford, Essex SS11 8DH
Call [phone]
Fax [phone]
Email [email protected]o.uk
Visit yewdale.co.uk
For more information on all
Yewdale products, please call
the sales department.
curtain track systems
yewdale.co.uk
see things differently
A concise approach to
a broad spectrum of
commercial curtain
track requirements with
simplistic control options
and designed for almost
every application.
®
cubicle and shower screens
yewdale.co.uk
see things differently
A dedicated range of privacy
and shower curtains with a
primary infection control
focus, providing an all-
encompassing solution to
increased levels of dignity.
®
cubicle and track systems
yewdale.co.uk
see things differently
The industry’s preferred
choice of maintenance
free privacy track systems
providing enhanced personal
welfare throughout the entire
healthcare and public sectors.
®
magnetic anti-ligature system
yewdale.co.uk
see things differently
The only fail-safe range of
exclusive anti-ligature products
designed to maximise the
safety of persons by removing
the death potential where
secure care is required.
®
fabric and blind systems
A comprehensive range
of window blind systems
designed with unique
technical features and to
the exacting specifications
that active commercial
environments demand.
yewdale.co.uk
see things differently
®