YitaHome HZXY-V1 User manual


ASSEMBLY INSTRUCTIONS
HZXY-V1

1





  









󾘉


  







Main Body
Handlebar
Handlebar Support
High-Pressure Hose
¼″ Connector
¼″ Quick Coupler
Locking Pins
Clevis Pins
Teflon Tape
Cleaning Pin
Spare Nozzles
Spare O-Rings
Not Included but Necessary
1、Adjustable Wrench
2、M6 Hex Wrench
3、Pressure Washer with High-Pressure Hose and ⅜″ Quick Coupler
4、Silicone Oil
1.Keep your work area well lit to avoid accidents.
2.Keep children, bystanders, and pets away while using this cleaner and store it out of reach
of children.
3.DO NOT operate this cleaner in cold conditions where the water supply might freeze or
behave erratically.
4.DO NOT operate this cleaner near any power supply, electrical equipment, or objects such as
glass that may shatter or cause injury when exposed to the pressurized spray.
5.DO NOT use this cleaner at pressures higher than 4000 psi (275 bars) or at feed rates greater
than 4 gpm (15 L/min.)
Imporant：
ASSEMBLY INSTRUCTIONS

2




Joint
Joint




 
 

1
1.Insert part C into part A, secure with 2 x part H and 2 x part G.
2.Attach part B to part C and secure with part H and part G.
ASSEMBLY INSTRUCTIONS





3

Control Handle
Outlet
Hub

 

2
3.Connect one end of part D to the control handle’s outlet on part B.
4.Connect the other end of part D to part E, then attach the connected parts D & E to part
F. Finally link to part A, making sure all parts are closely connected during the process.

ASSEMBLY INSTRUCTIONS

4
Maintenance
1.Over time, the nozzles may become obstructed from sediment, dust, or other debris. Check
periodically and unclog using the provided cleaning pin (J) and clean water immediately.
2.If any nozzle is damaged, replace it with one of the provided spares (K). Apply some Teflon
tape (I) to the thread of the replacement nozzle.
1.Lubricate moving parts with high-quality silicone oil (not included) periodically.
2.The exterior of the cleaner can be cleaned with a soft damp cloth. DO NOT use abrasive
cleaners or caustic chemicals.
3.If the cleaner won’t be used for an extended period of time, store in a cool and dry place
that’s inaccessible to children and away from freezing temperatures.
Nozzle
Miscellaneous
ASSEMBLY INSTRUCTIONS

Troubleshooting
ALWAYS cut off all power, drain all pressurized water, cool all heated surfaces, and disconnect
the cleaner from your pressure washer and water supply before performing any adjustment,
maintenance, or repairing of this device.
5
Common Problems
Weak cleaning power
Excessive vibration
Water leaks
Non-rotation of the bar
Possible Solutions
Ensure that your pressure washer’s operational pressure and
water flow rate are no less than 2000 psi (137.5 bars) and 2
gpm (7.5 L/min.) respectively.
Clear off any obstructions in the slots of the nozzles with the
cleaning pin.
Replace worn nozzles with the provided spares.
Retighten the bolts and nuts underneath the cleaner’s main body
with your adjustable wrench.
Retighten any loose connections.
Repair or replace any worn or damaged external parts, such as
the high-pressure hose.
1. Unscrew the bolts on the hub of the main body using your
M6 hex wrench and remove its housing.
2. Take out the swivel and replace any broken O-rings with the
provided spares (L) or correct their placement.
3. Install the swivel back into place and restore the hub.
ASSEMBLY INSTRUCTIONS

CONTACT US:
,
󾋸󾋿󾋿󾋿󾋾󾋸󾋾󾋿󾋷󾋿󾋻󾋿󾋷󾋷󾋻󾋺󾋷󾋿󾋷󾋷󾋸󾋹󾋷󾋷


󾋸
󾋹“”󽦁
󾋺“”