York Fitness York 2100 User manual

1
OO
2
ELLIPTICAL TRAINER
EXERCISES
&
INSTRUCTION
MANUAL
05 / 2000 TWN Product may vary slightly from pictured.

SAFETY GUIDELINES:
Please read and follow the following safety guidelines:
Before beginning any exercise program, you should consult with your doctor.
It is recommended that you undergo a complete physical examination.
,
Read this owner s manual and follow the instructions.
Assemble and operate the YORK 2100 ELLIPTICAL TRAINER on a solid, level surface.
Keep the area behind the YORK 2100 ELLIPTICAL TRAINER clear.
Always use your YORK 2100 ELLIPTICAL TRAINER in adequate space e.g., at least 2 ft.
(60cm) clearance on each side.
Never allow children on or near the YORK 2100 ELLIPTICAL TRAINER.
Always check the YORK 2100 ELLIPTICAL TRAINER before using it, in particular make sure
all parts are assembled, and nuts and bolts are tightened.
Do not use the YORK 2100 ELLIPTICAL TRAINER if the unit is disassembled in any way.
Keep hands away from moving parts.
The weight limit for this product is 225 lbs (100 kgs).
Wear proper workout clothing: Do not wear loose clothing.
Do not wear shoes with leather soles or high heels. Tie all long hair back.
Remove jewellery, rings, chains and pins before exercising.
Do not rock the unit from side to side.
Care should be taken when mounting and dismounting the unit.
Do not place any liquids on any part of the Elliptical Trainer 2100.
,
Do not use any accessories that aren t specifically recommended by the manufacturer,
these might cause injuries or cause the unit to fail.
Always consult your doctor before undertaking any exercise programme.
Work within your recommended exercise level, do NOT work to exhaustion.
If you feel any pain or abnormal symptoms, STOP YOUR WORKOUT IMMEDIATELY.
Consult your physician immediately.
YORK 2100 ELLIPTICAL TRAINER
The YORK 2100 ELLIPTICAL TRAINER is designed for the use and enjoyment of the serious
trainer as well as the dedicated user. By following the above precautions and using good
judgement and common sense, you will have safe and pleasurable exercise regimen with the
YORK 2100 ELLIPTICAL TRAINER.
CARE AND MAINTENANCE
Use a warm damp cloth with mild detergent
to keep your YORK 2100 ELLIPTICAL TRAINER
clean.
TOOLS REQUIRED
The tools enclosed in the carton are two
multi-purpose spanners (which one has a
screwdriver function) and one allen key.
SHOULD YOU REQUIRE ANY ASSISTANCE REGARDING THIS PRODUCT PLEASE CONTACT YORK DIRECTLY.
YORK BARBELL (U.K.) LTD.
CHURCHILLWAY,
DAVENTRY,
NORTHANTS, NN114YB
ENGLAND
TEL: [phone]
FAX: [phone]
E-MAIL: [email protected]
HELP LINE
(8:30am- 5:00pm)
YORK BARBELL (S.A.) (PTY) LTD.
P.O. BOX 14012,
WADEVILLE 1422
SOUTHAFRICA
TEL: [phone]
FAX: [phone]
E-MAIL: [email protected]
HELP LINE
(8:30am- 5:00pm)
YORK BARBELL (AUST.) LTD.
UNIT 1, LOT 2,
SWAFFHAM ROAD,
MINTO, N.S.W. 2566
AUSTRALIA
TEL: [phone]
FAX: [phone]
E-MAIL: [email protected]
HELP LINE
(8:30am- 5:00pm)

SHOULD YOU REQUIRE ANY ASSISTANCE REGARDING THIS PRODUCT PLEASE CONTACT YORK DIRECTLY.
**
1.
GENERAL
REMOVE ALL THE PARTS OF YOUR ELLIPTICAL TRAINER 2100 FROM
THE CARTON AND PLACE THEM ON THE FLOOR CAREFULLY.
ASSEMBLING YOUR ELLIPTICAL TRAINER 2100 IS SIMPLE.
FOLLOW THESE INSTRUCTIONS CAREFULLY AND IT SHOULD TAKE
YOU AROUND 15~20 MINUTES.
ASSEMBLY INSTRUCTION
ATTACH THE STABILIZERS
Fix the front stabilizer with moving wheels
to the main frame and secure, using two
carriage bolts, washers and locknuts.
Fix the rear stabilizer to the main frame
and secure,using two carriage bolts,
washers and locknuts.
X2
X2
X2
X2
X2
FRONT
STABILIZER
MOVING WHEEL
REAR
STABILIZER
END CAP
B
A
X2
NOTE: Make sure you fasten the nuts &
bolts securely for your safety and
comfort when exercising.

SHOULD YOU REQUIRE ANY ASSISTANCE REGARDING THIS PRODUCT PLEASE CONTACT YORK DIRECTLY.
**
2.
ATTACH THE FRONT POST
Rest the front post on the main frame carefully as
shown.
Connect the sensor wire plug to the middle wire socket.
Check middle wire runs up the front post and out
the top - later this will connect to the computer.
Insert the front post to the main frame in position and
secure, using four hex head bolts, spring washers and
washers as shown.
NOTE: TAKE CARE to ensure the middle wire does not
get trapped when you attach the front post to
the main frame.
Fix the plastic cap onto the bolts head.
X4
Attach the tension control to the front post and secure,
using two self tapping screws.
A
FRONT
POST
MAIN
FRAME
B
FRONT
POST
MAIN FRAME
BRACKET
C
D
X4
PLASTIC
CAP
X2

SHOULD YOU REQUIRE ANY ASSISTANCE REGARDING THIS PRODUCT PLEASE CONTACT YORK DIRECTLY.
**
3.
A
PEDAL
RIGHT
PEDAL POST
FRONT HOLE
B
RIGHT
PEDAL
POST
C
ATTACH THE PEDAL POSTS
Attach the pedal to the right pedal post and
secure, using two machine screws and three
thick washers as shown.
NOTE: Make sure you add two thick washers
with the screw for front hole when
assembling.
X2
X3
X1
X1
Fix the right pedal post to the right side
crank arm and secure, using one allen
head bolt as shown.
,, ,,
NOTE: The pedal posts are marked R
,, ,,
and L (Right & Left).
Tighten the allen head bolt to the crank
then fasten the nut to the allen head bolt
protruding through the crank arm.
This will secure it in place.
Repeat the same process for the left pedal
post assembly.
,, ,,
NOTE: The right pedal post R should be
threaded on clockwise.
,, ,,
The left pedal post L should be
threaded on clockwise.