York Fitness C410 User manual

Owner’sManual
C410 Upright Bike
Item #53100A
www.yorkfitness.com.au

Safety information
Please read this instruction manual before you begin
assembly. Great care has been taken to design these
instructions and following them will help you with
quicker assembly and minimize the risk of injury.
It isimportant that you keep these instructions for
future reference.
This list isnot exhaustive - You are responsible for your
own safety!
• Always assemble and operate the equipment on a
level surface.
• Ensure the equipment isstable before use.
• Always ensure that the equipment has adequate
space on each side.
• The safety level of this equipment can only be
maintained if itisregularly examined for wear and
tear.
• Replace defective components immediately and keep
the equipment out of use until itis repaired.
• Use only the adjustment setting as described in the
instructions. Always use the correct adjustment
pin /fixing.
• Always check that any pins / fixings are tight and
secure before use and after adjustment.
• Never leave any adjustment devices projecting from
the equipment.
• Always consult your doctor before undertaking any
exercise program.
• Always wear suitable clothing and footwear. (e.g.
tracksuit / shorts / training shoes)
• Remove all personal jewelrybefore exercising.
• Ensure you warm-up well before using the equipment
as this will help to prevent muscle strain.
• After eating, allow 1-2 hours before exercising as this
will help to prevent muscle strain.
• Never overload the equipment. (See maximum user
weight)
• Never use the equipment inanyother manner other
than the ways explained in these instructions and any
wall-chart supplied.
• Injuries to health may result from incorrect or
excessive training.
• Parents and others in charge of children should be
aware of their responsibility, because the natural play
instinct and the fondness of experimenting of children
can lead to situations and behavior for which the
training equipment isnot intended.
• The equipment isunder no circumstances suitable as
a children’s toy.
• If children are allowed to use the equipment, their
mental and physical development and above all their
temperament should be taken into account. They
should be controlled and instructed in the correct use
of the equipment.
• Children should not be allowed on or around the
equipment, especially when it is notin use.
• This appliance isnot intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
• This product isnot suitable for therapeutic purposes.
• This product has been tested for use in a home
environment and is warranted for In Home, personal,
family or household use.
• Due to our continuous policy of product development,
York Fitness reserves the right to change
specifications without notice.
CAUTION! The instructions must be followed carefully
in the assembly, use and maintenance of your
equipment. The warranty does not cover damage
due to negligence of the assembly, adjustment and
maintenance instructions described herein.
Safety Standards
This equipment meets the requirements of the EU’s
EMC and Low Voltage directives (where applicable),
EN957 1 & 7 - CLASS HC. Therefore the equipment
carries the followingmarks:
Maximum user weight: 130kg
2 www.yorkfitness.com.au

3
www.yorkfitness.com.au
Customer support
Should you require any assistance regarding this product please gather the
following information and then contact us using the details below:
• Serial No. - This can be found on the sticker.
• Original purchase date
• Place of purchase
• Information about the place and conditions of use
• Precise description of the issue / defect
IMPORTANT!! - Please retain your sales receipt, York Fitness Customer Care may request
proof ofpurchase to validate eligibility for warranty service. Warranty cover starts from the
date shown on the proof ofpurchase.
AUSTRALIA
The best way to contact us is via the website:
www.yorkfitness.com.au
York Fitness Australia
13/160 Hartley Road,
Smeaton Grange, NSW 2567
Tel: [phone]
Product’s Name
Use only on a level surface
Not suitable for therapeutic purpose
Manufacturer:
Contact:
Product Name:
Max UserWeight:
Safety Standards:
Electrical Info:
SERIAL NO:
BOYLES FITNESS EQUIPMENT
Unit 13, 160 Hartley Road, Smeaton Grange NSW 2567
C410 Upright Bike
130KG
EN957-1,7Class HC
Adaptor 9V,1300mA
53100A-
Serial Number
This product label is an example only, it is not the
real product name and serial number of the item
you have bought.

Exploded Diagram
4 www.yorkfitness.com.au

5 www.yorkfitness.com.au

Part list
No.
Description
Q'ty/ unit
A
Console
1
SET
A-1
Screw M5*P0.8*10L
4
PCS
B
Handlebar set
1
SET
B-1
Foam grip
2
PCS
B-2
Hand pulse
2
PCS
B-3
Hand pulse wire
1
PCS
B-4
Screw M4*20L
2
PCS
B-5
End cap
2
PCS
B-6
Handlebar
1
PCS
C
Handlebar post set
1
SET
C-1
Sensor wire (Upper)
1
PCS
C-2
Screw M5*P0.8*20L
2
PCS
C-3
Handlebar post
1
PCS
D
Main frame set
1
SET
D-1
Nylon M8*P1.0*20L
2
PCS
D-2
Knob
1
PCS
D-3
Sensor wire
1
PCS
D-4
DC wire
1
PCS
D-5
Screw M4*10L
1
PCS
D-6
Sensor fixed bracket
1
PCS
D-7
Flat washer
1
PCS
D-8
Wave washer
1
PCS
D-9
Flat washer
1
PCS
D-10
C clip
1
PCS
D-11
Bearing 6203
2
PCS
D-12
Sleeve for seat post
1
PCS
D-13
Left crank
1
PCS
D-14
Right crank
1
PCS
D-15
Belt
1
PCS
D-16
Left chain cover (upper)
1
PCS
D-17
Right chain cover (lower)
1
PCS
D-18
Crank cap
2
PCS
D-19
Screw M5*16
4
PCS
D-20
Screw M4*50L
6
PCS
D-21
Washer of handlebar post
2
PCS
D-22
Servo motor set
1
PCS
6 www.yorkfitness.com.au

D-23
Motor wire
1
PCS
No.
Description
Q'ty/ unit
D-24
Screw M8*P1.25*20L
4
PCS
D-25
Semi washer
4
PCS
D-26
Axle
1
PCS
D-27
Hexagonal screw M8*P1.25*12L
3
PCS
D-28
Pulley
1
PCS
D-29
Bushing
1
PCS
D-30
Pedal set
1
PCS
D-31
Cap of handlebar post
1
PCS
D-32
Main frame
1
PCS
E
Water bottle cage
1
SET
F
Flywheel set
1
SET
F-1
Nut 3/8'
5
PCS
F-2
Flywheel axle
1
PCS
F-3
Single wheel
1
PCS
F-4
Pulley
1
PCS
F-5
Bearing 6900RS
1
PCS
F-6
Bearing 6003RS
1
PCS
F-7
Bearing 6203
1
PCS
F-8
Bearing 6300RS
1
PCS
F-9
Flat washer
1
PCS
F-10
Star washer
2
PCS
F-11
Bushing of flywheel
1
PCS
F-12
Bushing of flywheel
1
PCS
F-13
Flywheel
1
PCS
G
Idler set
1
SET
G-1
Idler wheel
1
PCS
G-2
Nut M8
1
PCS
G-3
Flat washer
1
PCS
G-4
Hexagonal screw M8*P1.25*18L
1
PCS
G-5
Wave washer
2
PCS
G-6
Flat washer
1
PCS
G-7
Hexagonal screw M6*P1.0*12L
1
PCS
G-8
Idler spring
1
PCS
G-9
Idler
1
PCS
H
Magnet set
1
SET
H-1
Flat washer
2
PCS
H-2
Hexagonal screw M6*P1.0*16L
2
PCS
H-3
Spring washer
2
PCS
7 www.yorkfitness.com.au

H-4
Magnet
1
PCS
No.
Description
Q'ty/ unit
I
Front stabilizer set
1
SET
I-1
Front stabilizer pad
1
PCS
I-2
Front stabilizer pad
1
PCS
I-3
Screw 3/16'
2
PCS
I-4
Front stabilizer
1
PCS
J
Rear stabilizer set
1
SET
J-1
Adjust small pad
2
PCS
J-2
End cap of stabilizer
2
PCS
J-3
Screw 3/16'
4
PCS
J-4
Rear stabilizer
1
PCS
K
Seat post
1
PCS
L
Seat slider set
1
SET
L-1
Fixing screw bracket
1
PCS
L-2
Knob of seat
1
PCS
L-3
Flat washer
1
PCS
L-4
End cap
2
PCS
L-5
Seat slider
1
PCS
M
Hardware kit set
1
PCS
M-1
Screw M8*P1.25*75L
2
PCS
M-2
Nut M8
2
PCS
M-3
Semi washer
2
PCS
M-4
Screw M8*16
4
PCS
N
Switching power adapter
1
SET
O
Seat
1
SET
8 www.yorkfitness.com.au

Assembly Stage #1
Allen Bolt M8*16L (4) M-4
1. Attach the front Stabilizer (I) to the main Frame (D) using two screws (M-4).
2. Attach the rear Stabilizer (J) to the main Frame (D) using two screws (M-4).
Assembly Stage #2
1. Assemble the two pedals (D-30L+D-30R) onto the Crank (D-13L, D-14R) with a screw driver.
Remarks: Screw the left pedal’s spindle counter-clockwise and the right pedal’s
spindle clockwise. Use a wrench (or screwdriver) to screw the two spindles completely.
9 www.yorkfitness.com.au

Assembly Stage #3
1. Assemble the seat (O) to the seat slider. The Slider can be adjusted in different angles. Tighten
the two Nuts under the Seat using a screwdriver. In addition, the Slider can be adjusted in
horizontal level by loosening the Knob.
2. Insert the seat post (K) into the main frame (D), and then choose the desired position,
and tighten the knob (D-2). Be sure the knob is always tightened.
Remarks: When you have chosen a desired position, and tighten the Seat Post Knob
until you hear a “click”.
10 www.yorkfitness.com.au

Assembly Stage #4
1. Connect the sensor wires Upper & lower (C-1, D-23).
2. Insert the handlebar post (C-3) to the main frame with screw (D-24)
and semi-circular washers (D-25) with Allen wrench.
11 www.yorkfitness.com.au

Assembly Stage #5
Box Spanner(1)
Acorn Nut for M8 Bolt (2) M-2
Curved Washerφ8*φ19*2T (2) M-3
Carriage Bolt M8*75L(2) M-1
1. Pass the hand-pulse wire (B-3) through the hole.
2. Assembly the handlebar (B) onto the handlebar post (C-3) by using screws (M-1),
Nut (M-2) and Semi washer (M-3).
12 www.yorkfitness.com.au

Assembly Stage #6
Box Spanner(1)
Plug the wire (B-3 & C-1) and assemble the computer (A) with 4 screws (A-1) by wrench.
13 www.yorkfitness.com.au

Assembly Stage #7
Box Spanner(1)
1. Assemble water bottle cage by using screws (C-2).
2. Plug the adapter (N) into socket as picture above.
14 www.yorkfitness.com.au

TOOLS & PARTS
B580
Screwdriver (1)
Box Spanner(1)
Allen Key(1)
Acorn Nut for M8 Bolt (2) M-2
Curved Washerφ8*φ19*2T (2) M-3
Allen Bolt M8*16L (4) M-4
Carriage Bolt M8*75L(2) M-1
B580
Screwdriver(1)
BoxSpanner(1)
AllenKey(1)
Acorn Nut forM8Bolt (2) M-2
CurvedWasherφ 8*φ19*2T ( 2) M-3
AllenBolt M8*16L(4) M
CarriageBolt M8*75L(2)M-1 说明书
15 www.yorkfitness.com.au

SM3752 INSTRUCTION MANUAL
DISPLAY FUNCTIONS :
ITEM
DESCRIPTION
TIME
.Workout time displayed during exercise.
.Range 0:00 ~ 99:59
SPEED
.Workout speed displayed during exercise.
.Range 0.0 ~ 99.9
DISTANCE
.Workout distance displayed during exercise.
.Range 0.0 ~ 99.9
CALORIES
.Burned calories during workout display.
.Range 0 ~ 999
PULSE
.Pulse bpm displayed during exercise.
.Pulse alarm when over preset target pulse.
RPM
.Rotation per minute
.Range 0 ~ 999
WATTS
.Workout power consumption
.Range 0 ~ 350
MANUAL
.Manual mode workout.
PROGRAM
.12 PROGRAM selection.
USER
.User creates resistance level profile.
H.R.C.
.Target HR training mode.
WATT
.Watt constant training mode.
16 www.yorkfitness.com.au

KEYS :
OPERATION:
POWER ON
Plug in power supply, computer will power on and display all segments on LCD for 2 seconds. After 4
minutes without pedaling or pulse input, console will enter into power saving mode.
Press any key may wake the console up.
Manual Mode
Press START in main menu may start workout in manual mode.
1. Press UP or DOWN to select workout program, choose Manual and press MODE to enter.
2. Press UP or DOWN to preset TIME.DISTANCE.CALORIES.PULSE and press MODE to confirm.
3. Press START/STOP keys to start workout. Press UP or DOWN to adjust load level.
4. Press START/STOP keys to pause workout. Press RESET to reverse to main menu.
Program Mode
1. Press UP or DOWN to select workout program, choose Program and press MODE to enter.
2. Press UP or DOWN to preset workout TIME.
3. Press START/STOP keys to start workout. Press UP or DOWN to adjust load level.
ITEM
DESCRIPTION
Up
‧Increase resistance level
Down
‧Decrease resistance level
Mode
‧Confirm setting or selection.
Reset
‧Hold on pressing for 2 seconds, computer will reboot and start from user
setting.
‧Reverse to main menu during presetting workout value or stop mode.
Start/ Stop
‧Start or Stop workout.
Recovery
‧Test heart rate recovery status.
2 www.yorkfitness.com.au
17 www.yorkfitness.com.au

Press START/STOP keys to pause workout. Press RESET to reverse to main menu.
User Program Mode
1. Press UP or DOWN to select workout program, choose User and press MODE to enter.
2. Press UP or DOWN to set load level of each column, and press MODE to next one. (Total column =
20)
3. Hold on pressing MODE to finish or quit setting.
4. Press UP or DOWN to preset workout TIME.
5. Press START/STOP button to start workout. Press UP or DOWN to adjust load level.
6. Press START/STOP button to pause workout. Press RESET to reverse to main menu.
H.R.C. mode
1. Press UP or DOWN to select workout program, choose H.R.C. and press MODE to enter.
2. Press UP or Down to select 55%.75%.90% or TAG (TARGET H.R.) (default: 100).
3. Press UP or DOWN to preset workout TIME.
4. Press START/STOP button to start or stop workout. Press RESET to reverse to main menu.
WATT Mode
1. Press UP or DOWN to select workout program, choose WATT and press MODE to enter.
2. Press UP or DOWN to preset WATT target. (default: 120)
3. Press UP or DOWN to preset TIME.
5. Press START/STOP button to start or stop workout. Press RESET to reverse to main menu.
18 www.yorkfitness.com.au

Recovery
1. When pulse value display on the computer (hold handgrip or wear chest strap), press RECOVERY
button.
2. TIME shows "0:60" (seconds) and count down.
Computer will show F1 to F6 after count down to 0 to test heart rate recovery status.
NOTE:
1. When user stop pedaling for 4 minutes, computer will enter into power save mode, all
setting and exercise data will stored until user start exercise again.
2. When computer act abnormal, please plug out the adaptor and plug in again.
19 www.yorkfitness.com.au

WARRANTY, SAFETY AND ASSEMBLY
INFORMATION YRK53100A–YORK C410
IMPORTANT
Please read and retain this manual as it will assist with identification for parts and service.
------------------------------------------------------------------------------------------------------------
BOYLES FITNESS warrants their Cross Trainer to be free from defects in material and
workmanship under normal use and service conditions.
The various components of the Cross Trainer are warranted against defects and
workmanship for the time periods specified as follows:
YRK53100A –YORK C410
Domestic use
Lifetime frame & 1 year on all other parts.
All warranty coverage extends only to the original retail purchaser from the date of
purchase. BOYLES FITNESS’ obligation under this Warranty is limited to replacing or
repairing, at BOYLES’ option, the product or parts therein. Any enquiries relating to
warranties or spare parts must be directed to Service 07 3272 7010 .
For efficient processing of your enquiry please have relevant date of purchase, retailer
name you purchased the item from and the brand on the product. This warranty does not
extend to any damage to a product caused by abuse, improper or abnormal usage (as
detailed in this instruction manual), or repairs not provided by BOYLES. Nor does this
warranty extend to products used for commercial or rental purposes. This warranty does
not cover ordinary wear, tear and weathering, failure to follow directions, improper
installation, improper maintenance or acts of God (such as damage caused by storms,
lightning and by snow or ice). No other Warranty beyond that specifically set forth above is
authorised by BOYLES.
Our sales and service centre has been set up to provide assembly assistance, replacement
parts and accessories, and to efficiently handle all warranty related matters.
Phone [phone]
Hours 9:00am – 4:00pm Mon-Fri (excluding public holidays),
Email sp[email protected]
Website www.bfe.net.au
4 www.yorkfitness.com.au
20 www.yorkfitness.com.au