your zone YZW-10002 User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Date 2019-09-16 Rev. 0001-B
Beckett Futon Bunk Bed
Stock # YZW-10002
TWO ADULTS ASSEMBLY REQUIRED
If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the
store where it was purchased. Please call our customer service number and have your instructions
and parts list ready to provide the model name, part name or factory number:
866-942-5362
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday - Friday
Or visit our web site 24 hours a day, 7 days a week for product assistance at
www.whalenstyle.com
Or e-mail your request to [e-mail]
LOT NUMBER:
DATE PURCHASED: / /

2
ALWAYS USE GUARDRAILS ON BOTH LONG SIDES OF THE BUNK. IF THE
BUNK BED WILL BE PLACED NEXT TO THE WALL, THE GUARDRAIL THAT
RUNS THE FULL LENGTH OF THE BED SHOULD BE PLACED AGAINST THE
WALL TO PREVENT ENTRAPMENT BETWEEN THE BED AND WALL.
STRANGULATION HAZARD - Never attach or hang items to any part of the bunk bed
that are not designed for use with the bed; for example, but not limited to, hooks, belts,
and jump ropes.
Prohibit more than one person on upper bunk.
Maximum mattress thickness must not exceed 5 in. (12.70 cm). Surface of mattress must
be at least 5 in. (12.70 cm) below the edge of guardrails.
Use only mattress which is 74 in. (1.88 m) to 75 in. (1.90 m) long and 37½ in. (95.25 cm) to
38½ in. (97.79 cm) wide on the upper bunk.
Use only mattress which is 74 in. (1.88 m) to 75 in. (1.90 m) long and 52½ in. (133.4 cm) to
53½ in. (135.9 cm) wide on the lower bunk.
Replacement parts, including additional guardrails, may be obtained from any of our
dealers.

3
TO HELP PREVENT SERIOUS OR FATAL INJURIES FROM ENTRAPMENT
OR FALLS
 Follow the information on the warnings appearing on the upper bunk end
structure and on the carton. Do not remove warning label from bed.
 Always use the recommended size mattress or mattress support, or both, to help
prevent the likelihood of entrapment or falls.
 Surface of mattress must be at least 5 in. (12.70 cm) below the upper edge of
guardrails.
 Do not allow children under 6 years of age to use the upper bunk.
 Periodically check and ensure that the guardrail, ladder and other components
are in their proper position, free from damage and that all connectors are tight.
 Do not allow horseplay on or under the bed and prohibit jumping on the bed.
 Always use the ladder for entering and leaving the upper bunk.
 Do not use substitute parts. Contact the manufacturer or dealer for replacement
parts.
 Use of a night light may provide added safety precaution for a child using the
upper bunk.
 Always use guardrails on both long sides of the upper bunk. If the bunk bed will
be placed next to the wall, the guardrail that runs the full length of the bed
should be placed against the wall to prevent entrapment between the bed and
wall.
 The use of water or sleep flotation mattress is prohibited.
 STRANGULATION HAZARD – Never attach or hang items to any part of the
bunk bed that are not designed for use with the bed; for example, but not limited
to, hooks, belts, and jump ropes.
 Prohibit more than one person on upper bunk.
 Keep these instructions for future reference.

4
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
A- Left Front / Right Back Post B- Left Back / Right Front Post
(Qty. 2) (Qty. 2)
C- Lower Side Rail D- Mattress Side Rail
(Qty. 2) (Qty. 2)
E- Guardrail F- Upper Headboard Cross Assembly
(Qty. 2) (Qty. 1)
G- Upper Footboard Cross Assembly H- Left Lower Side Frame
(Qty. 1) (Qty. 1)
I- Right Lower Side Frame J- Ladder
(Qty. 1) (Qty. 1)

5
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
K- Mattress Support Slat L- Back Frame
(Qty. 7) (Qty. 1)
M- Seat Frame N- Support Leg
(Qty. 1) (Qty. 1)
O- Left Sofa Mechanism P- Right Sofa Mechanism Q- Side Stretcher
(Qty. 1) (Qty. 1) (Qty. 12)
(1) 1/4” x 3/4” Bolt (2) 1/4” x 1 1/4” Bolt (3) 1/4” x 2” Bolt
(Qty. 92+2 extra) (Qty. 4+1 extra) (Qty. 2+1 extra)
(4) 1/4” x 5/16” Bolt (5) Steel Cable (6) Velcro Strap Hex Wrench
(Qty. 8+1 extra) (Qty. 5) (Qty. 1) (Qty. 2 )
Tools required: Hex wrench (provided)

6
ASSEMBLY INSTRUCTIONS
NOTE: Please follow the instructions carefully to insure a safe and sturdy bed. Do not fully
tighten the bolts until all rails and guardrails are attached.
1. Unpack the units and confirm that you have all hardware and required parts. Assemble the unit on a
carpeted floor or the empty carton to avoid any scratch.
2. Align and attach the Upper Footboard Cross Assembly (G), six Side Stretchers (Q) and the Lower
Footboard Side Frame (H) between the Posts (A and B) by inserting twenty-one 3/4” Bolts (1) and screw
into place.
① x 21
B
A
G
1
1
I
Q

7
ASSEMBLY INSTRUCTIONS
3. Repeat the same procedure to attach the Upper Headboard Cross Assembly (F), six Side Stretchers (Q)
and Right Lower Side Frame (I) between the Posts (A and B).
① x 22
1
F
A
B
Q
1
I
Q

8
ASSEMBLY INSTRUCTIONS
4. Ask for assistance to stand the assembled unit upright.
5. Align and attach the Lower Side Rails (C) between the Posts (A and B) with eight 3/4” Bolts (1).
A
B
B
A
C
C
1
1
① x 8

9
ASSEMBLY INSTRUCTIONS
6. Align and attach the Mattress Side Rails (D) between the Posts (A and B) with eight 3/4” Bolts (1).
A
B
B
A
D
D
1
1
① x 8

10
ASSEMBLY INSTRUCTIONS
7. Attach the Guardrails (E) between the Posts (A and B) with eight 3/4” Bolts (1).
8. Insert two 2” Bolts (3) through the mounting holes on the center of the Mattress Side Rails (D) and
screw into the middle tubes of the Guardrails (E).
① x 8
③ x 2
D
D
E
E
A
B
B
A
1
1
3

11
ASSEMBLY INSTRUCTIONS
9. Fit the Mattress Support Slats (K) between the U-brackets on both Mattress Side Rails (D) as shown and
fasten them in place with the 3/4” Bolts (1).
① x 14
D
D
K
K
K
K
1

12
ASSEMBLY INSTRUCTIONS
10. Fasten the Left Sofa Mechanism (O) to the Left Lower Side Frame (H) with two 3/4” Bolts (1).
11. Repeat the same procedure to attach the Right Sofa Mechanism (P) to the Right Lower Side Frame (I).
① x 4
H
I
O
P
1
1O / P
H / I

13
ASSEMBLY INSTRUCTIONS
12. Fasten the Support Leg (N) to the Seat Frame (M) with two 3/4” Bolts (1).
① x 2
M
N
11

14
ASSEMBLY INSTRUCTIONS
13. Ask for assistance to put the Seat Frame (M) onto the Sofa Mechanisms (O and P) and rest onto the
Front Lower Side Rail (C). Make sure that the mounting holes overlap the threaded sockets properly and
the handles face upward.
14. Insert four 5/16” Bolts (4) through the mounting holes on the Sofa Mechanisms (O and P) and securely
screw into the Seat Frame (M).
④ x 4
M
O
P
O / P
4
M

15
ASSEMBLY INSTRUCTIONS
15. Align and attach the Back Frame (L) to the Sofa Mechanisms (O and P) with four 5/16” Bolts (4).
④ x 4
O
P
L
O / P
L
4

16
ASSEMBLY INSTRUCTIONS
16. Lift the handles on the Seat Frame (M) and swing the Back Frame (L) backward until rest them onto the
Lower Side Rails (C).
17. Secure both Back Frame (L) and Seat Frame (M) to the Sofa Mechanisms (O and P) with four 3/4” Bolts
(1).
① x 4
L
M
O
P
O / P
M
L
1
1

17
ASSEMBLY INSTRUCTIONS
18. Go back and fasten all the bolts with the provided hex wrench.
19. Tie down the adjacent tubes of the Back Frame (L) and Seat Frame (M) with five Steel Cables (5) as
shown.
⑤ x 5
L
M
M
L
5

18
ASSEMBLY INSTRUCTIONS
20. Align and attach the Ladder (J) to the Upper Footboard Cross Assembly (G) and Lower Side Frame (H)
with four 1 ¼” Bolts (2).
21. Lift the Seat Frame (M) and Back Frame (L) slightly and swing the Back Frame (L) to the inclined
position to form a sofa.
② x 4
G
H
J
2

19
ASSEMBLY INSTRUCTIONS
22. Lift the Seat Frame (M) and swing the Back Frame (L) backward until rest them onto the Lower Side
Rails (C) to form a bed.
23. Attach the Adhesive Strap (6) to the inside of Lower Front Side Rail (C) with one 3/4” Bolt (1).
24. Tie down the Lower Front Side Rail (C) and one adjacent tube of the Seat Frame (M) with the Adhesive
Strap (6) to prevent the Seat Frame (M) from being lifted randomly which may cause possible bodily
harm.
⑥ x 1
① x 1
6
C
M
6
C
M
1
6
C
C
M
L
M
C

20
OPTIONAL CONFIGURATION
NOTE: The Upper headboard and footboard cross assembly (F and G) are interchangeable so that the
ladder can be attached either side.
25. Depending on the layout of your room, you can change the Ladder (J) to the right side.
(1) Unscrew the bolts to remove the Ladder (J).
(2) Unscrew the bolts to remove the Upper Headboard Cross Assembly (F) and Upper Footboard Cross
Assembly (G) and reverse the location.
(3) Align and attach the Ladder (J) to the Upper Footboard Cross Assembly (G) and the Right Lower
Side Frame (I).
G
J
F
G
J
F