Yuan Multi2SDI User manual

Multi2SDI
BOX
User Manual
Rev1.3

Content
Feature ...................................................................................3
Front Panel...............................................................................4
Rear Panel................................................................................4
Top Panel.................................................................................5
Side Panel ................................................................................5
Button/LED Indicate ....................................................................6
Installation ............................................................................. 17
Package Contents ..................................................................... 17
Specifications.......................................................................... 18
Firmware Upload ...................................................................... 19
Appendix Table A ..................................................................... 21
Update List............................................................................. 22

Feature
SDI Supports HD formats :
720p50 & 60
1080i50 & 60
1080p24, 25, 30, 50 & 60
SDI Support 525i & 625i SD D1 format
Auto 3G/HD/SD-SDI detection
Can be split one 3G-SDI displays simultaneously.
Frame rate conversion(1.000/1.001)
External Button Configuration
Firmware is upgradable in the field using the integrated USB port
The converter is Plug-and-Play
Support DVI-D, DVI-A, Component, CVBS and S-Video Input

Front Panel
NO
Component
Function
1
SDI Output Port
From your SDI Display Device plug into this ports
2
Mode Buttons
Select Format/Output Port
3
Power Jack
The Power adapter plug into here
Rear Panel
NO
Component
Function
1
Phone Jack
Form you Audio Device plug into this port
2
Component/CVBS/S-Video
Input Port
From your YPbPr/CVBS/S-Video Device plug
into this port
3
DVI-D/DVI-A Input Port
From your DVI-D/DIV-A Device plug into this
port
1
3
1
3
2
2

Top Panel
NO
Component
Function
1
Input Source LED
The LEDs are indicate Input source
2
Power and Lock LED
The LEDs is indicate power and signal locked.
3
Main Format LED
The LEDS are indicate output format
Side Panel
NO
Component
Function
1
USB Port
Upgrade firmware/Control Box From PC
1
1
2
3

Button/LED Indicate
1. Firmware Mode:
Hold on the 1 and 2 button, the display is showed firmware version on display of
left upper.
FIRMWARE VERSION
0.1.0.1
2. Default Mode:
Pull all button (1, 2 and 3) at same time, the box auto reset to default.
3. Audio Mode
Pull all button 2 to setting audio Mode..
DVI-D
Embadded Audio (Default)
External Audio
Mute
DVI-A
Mute
YPbPr
Composite
External Audio
SVIdeo

4. Output Format Mode:
Pull button 1 change to format mode, frame rate and Fraction by button 2 and 3.
Button 1
Button 2
Button 3
720x480
59.94i
720x576
50i
1280x720
60p
59.94p
50p
30p
25p
1920x1080
60i
59.94i
50i
60p
59.94p
50p
30p
29.97p
25p
24p
23.98p
720x480 59.94i
1
2
3

720x576 i50
1280x720 p60
12080 x720 p59
1280x720 p50

1280x720 p30
1280x 720 p25
1920x1080 i60
1920x1080 i59

1920x1080 i50
1920x1080 p60
1920x1080 p59
1920x1080 p50

1920x1080 p30
1920x1080 p29
1920x1080 p25
1920x1080 p24

1920x1080 p23
4. Aspect Ratio Mode:
Check the button 3 , the box will be seting to Aspect Ratio Mode.
Mode
Display
16:9
(Default)
4:3
1:1
(dot by dot)

5. Function Button Mode:
Hold on the button 4 until show the Func button Mod
6. Auto Phase Mode:
When input souce is DVI-A (VGA) and Hold on the button 1 will be start auto phase
function. ( about 3 sec )
7. Input Source Mode:
Pull button 4 change to input source mode. The button 3 and 4 can be switch
output source.
DVI-D/DVI-A
Pb/CVBS
Y/Y
Pr/C
DVI-D
●
○
○
○
DVI-A
●
○
○
○
YPbPr
○
●
●
●
CVBS
○
●
○
○
S-VIDEO
○
○
●
●
FUNCTION BUTTON
UN-LOCK/LOCK

1. DVI-D + L/R Audio:
DVI-D + L/R Audio
2. DVI-A+ L/R Audio:
DVI-A + L/R Audio

3. YPbPr + L/R Audio:
YPbPr + L/R Audio
4. Composite (CVBS) + L/R Audio:
Composite(CVBS) + L/R Audio

5. S-VIDEO + L/R Audio
Composite(CVBS) + L/R Audio

Installation
MULTI2SDI installation consists of the following:
1. Disconnect +12DC adaptor to converter.
2. Connect Video Source to the Input Connector.
3. Connect Display Equipment to the output’s connector
4. Connect the +12DC adaptor to the converter.
Package Contents
The MULTI2SDI -S package contains the following items:
User Manual x 1
+12 DC Adapter x 1
MULTI2SDI Converter x 1

Specifications
DESCRIPTION
SDI Format
SD-SDI, HD-SDI & 3G-SDI
SDI Transition Rate
2.970Gb/s, 10485Gb/s and 270Mb/s
Audio Support
8-Channel (L/R Audio only 2 channel splitter to 8
channel)
Re-Sample Clock
Auto Resample audio clock to 48Khz
Coaxial Cable Type
RG6/RG59(75Ω)
Cable Equalization
3G: 100m of RG6 / 86m of RG59
HD: 170m of RG6 / 120m of RG59
SD: 400m of RG6 / 280m of RG59
*1 RG6: CANARE L-5CFB Cable / RG59: Belden 9275 Cable
*2 Cable Length Performance: Depending on SDI Signal and
Cable Quality
Input Format Support
Appendix Table A
Output Format Support
Appendix Table A
Firmware Updates
Via Mini-USB
Output Connector
1 x BNC [SDI]
Input Connector
1 x BNC [SDI]
1 x DVI-I [DVI-D + DVI-A]
3 x BNC [YPbPr or YC + CVBS ]
1 x Phone Jack
BNC Connector
3G 75 Ωinter-locked socket
USB Connector
Mini-USB
Bottom
Output Format/Audio Source/TV Ratio
Housing
SECC
Dimension
L:153mm x W:63.3mm xH:26mm
Power Source
Power Adapter: AC 100 ~ 240 V/DC (+6 ~ 15 V)
Operation Temperature
0~50°C [32~114°F]
Storage Temperature
-20~+60°C

Firmware Upload
Firmware is upgradable in the field using the integrated USB port
How to Firmware upgrade:
Step1.
Open Upload Firmware Program tools.exe and connect box to PC by USB Cable.
Step2.
Plug and un-plug “DC adapter” to power on/off the converter box (the
connection check status will be changed to “Connect”)

Step3.
Plug and un-plug “DC adapter” again (the connection check status will be
changed to “Connected”) and Please click the Open File button to select the
firmware bin file.
Step4.
Please click “Start’ Button to proceed with new firmware programming. The
PASS message will appear when the procedures finished.
Step5.
Close Upload Firmware Program tools