YUNKE CHINA DCWL-7962OT User manual

DCWL-7962OT Outdoor AP Installation
Manual
DCWL-7962OT 室外型无线接入点产品
安装指导
Manual Version: v1.1

DCWL-7962OT Outdoor AP
Installation Manual Content
1
Content
CHAPTER 1 DEVICE INTRODUCTION....................................1-1
CHAPTER 2 PREPARATION FOR INSTALLATION ................2-1
2.1 INSTALLATION PRECAUTIONS ...............................................................2-1
2.2 INSTALLATION ENVIRONMENT REQUIREMENTS.......................................2-1
2.3 EQUIPMENT ACCESSORIES...................................................................2-1
2.4 INSTALLATION TOOLS ..........................................................................2-2
CHAPTER 3 AP INSTALLATION..............................................3-1
3.1 INSTALLATION PROCESS ......................................................................3-1
3.2 CHECKING BEFORE INSTALLATION ........................................................3-2
3.3 ENSURE THE INSTALLATION POSITION...................................................3-2
3.4 INSTALL DCWL-7962OT(R5) .............................................................3-2
3.4.1 Column Holding Installation ................................................................3-2
3.4.2 Wall Hanging Installation .....................................................................3-4
3.5 CONNECT CABLES ..............................................................................3-6
3.5.1 Connect Network Cables......................................................................3-6
3.5.2 Connect Ground Cables.......................................................................3-7
3.5.3 Connect RF Cables...............................................................................3-7
3.6AP POWER.........................................................................................3-8
3.6.1 Checking before Power........................................................................3-8
3.6.2 PoE Power.............................................................................................3-8
3.6.3 Checking after Power ...........................................................................3-8
3.7 CONNECT AP TO INTERNET..................................................................3-8

DCWL-7962OT Outdoor AP
Installation Manual Chapter 1 Device Introduction
1-1
Chapter 1 Device Introduction
DCWL-7962OT(R5) outdoor AP is shown as below:
Fig 1-1 DCWL-7962OT（R5）AP
The ports explanation of DCWL-7962OT outdoor AP is as below:
Table 1-1 ports explanation
No. Name Explanation

DCWL-7962OT Outdoor AP
Installation Manual Chapter 1 Device Introduction
1-2
1 5G-1 5G antenna interface 1
2
5G-2 5G antenna interface 2
3 2.4G-1 2.4G antenna interface 1
4 2.4G-2 2.4G antenna interface 2
5 PoE PoE interface, PoE power and Ethernet interface
6 GND Ground point
7 Reset AP reset hole
The basic configuration of DCWL-7962OT outdoor AP is as below:
Table 1-2 basic configuration
Product Model Applicable Protocols
Antenna Maximum Power
DCWL-7962OT(R5) • IEEE802.11a/b/g/n
• Double Radiofrequency
Provide external
antenna 24W
The shape size and weight of DCWL-7962OT outdoor AP is as below:
Table 1-3 the shape size and weight
Product Model Shape Size Weight
DCWL-7962OT(R5)（W × D × H）220 × 220 × 100mm 3.80kg

DCWL-7962OT Outdoor AP
Installation Manual Chapter 2 Preparation for Installation
2-1
Chapter 2 Preparation for Installation
2.1 Installation Precautions
Only allow the professionals installing and disassembling the device and its annex.
Before the installation and configuration, please read the related security introduction
carefully.
Adopt the appropriate security measures to avoid the personal injury and
equipment damage.
Please put the device on the dry and flat place and ensure the anti-skid
measures.
Keep the device clean without dirt.
Do not put the device and the installation tools in the walking area.
2.2 Installation Environment Requirements
Before the installation, please check the installation conditions of the device to make
sure that the device is in the good operating environment in a long time. Check this with
the following aspects.
The temperature and humidity environment requirements of the device are as below:
Table 2-1 The temperature and humidity index
Items Range
Standard working environment temperature (outdoor) -40℃～60℃
Storage temperature -45℃～70℃
Working humidity (non-condensing) 5%～95%
2.3 Equipment Accessories
Please refer to the packing list.

DCWL-7962OT Outdoor AP
Installation Manual Chapter 2 Preparation for Installation
2-2
2.4 Installation Tools
When installing DCWL-7962OT outdoor AP, the following tools may be used
(user-owned).
Horizontal
ruler Permanent marker Knife Wire stripper Network pliers
Impact drill (1)
and some
supporting drills
Rubber
hammer
Phillips
screwdriver
Ladder

DCWL-7962OT Outdoor AP
Installation Manual Chapter 3 AP Installation
3-1
Chapter 3 AP Installation
Because the installation position of DCWL-7900 series indoor AP is high normally, the
maintenance personal cannot maintain and debug through the console port to login the
device after installation. We suggest user conducting the basic configuration according to
need before installing the AP to the appointed position.
3.1 Installation Process
Fig 3-1 AP installation flow diagram

DCWL-7962OT Outdoor AP
Installation Manual Chapter 3 AP Installation
3-2
3.2 Checking before Installation
Please check the following items before the AP installation:
Please power to the AP first and connect the AP to the Ethernet, then check the
LED status to make sure the AP can work normally.
Please ensure to complete the wiring in the position of AP installation.
DCWL-7962OT (R5) outdoor AP supports 802.3at standard PoE (Power over
Ethernet) power.
Please record AP’s MAC address and serial number (MAC address and serial
number are on the back of the AP) first for convenient to find and use.
3.3 Ensure the Installation Position
The rules of installation position are as below:
Cut back the obstacles (such as walls) between AP and the user terminal device
as much as possible.
Make the AP’s position far away from the electrical device that can bring the RF
noise (such as the microwave).
The installation position should be hidden as much as possible to prevent
disturbing the inhabitants.
3.4 Install DCWL-7962OT(R5)
The following two installation methods are supported for DCWL-7962OT (R5) outdoor
AP:
Column holding installation
Wall hanging installation
3.4.1 Column Holding Installation
When install the DCWL-7962OT (R5) outdoor AP on the column, the steps are as
below:
1. Install the backplane at the bottom of DCWL-7962OT (R5), and screw the 4pcs
short screws with the phillips screwdriver. Make the long screw stick passing through the
holes of the backplane and put the flat pad, spring shim and the screw nut on it in proper
order; do not lock it tight.

DCWL-7962OT Outdoor AP
Installation Manual Chapter 3 AP Installation
3-3
Fig 3-2 Install the backplane of DCWL-7962OT (R5) AP
2. Lock the 2PCS stainless tight hoop strip on the stick by passing through the
mounting bracket and lock the fastening screws.
Fig 3-3 Column holding installation of DCWL-7962OT(R5) AP
3. Install the device with the backplane to the mounting kit on the column and fix the
device and mounting kit together by using 2pcs short screws and 1pcs long screws.

DCWL-7962OT Outdoor AP
Installation Manual Chapter 3 AP Installation
3-4
Fig 3-4 fixed installation of DCWL-7962OT(R5) AP
3.4.2 Wall Hanging Installation
When install the DCWL-7962OT (R5) outdoor AP with wall hanging method, the
steps are as below:
1. As shown in the fig 3-1, install the backplane at the bottom of DCWL-7962OT (R5)
first;2. Make the AP wall mounting kit flat against the wall and mark the holes that the
crews needs to be installed into, and then punch four holes with the impact drill; Insert the
expansion bolt into the holes and use the rubber hammer beating it until the expansion
bolt got into the wall completely;

DCWL-7962OT Outdoor AP
Installation Manual Chapter 3 AP Installation
3-5
Fig 3-5 Wall drilling
3. Correspond the screw holes to the expansion bolt holes on the wall, and make the
crews pass through the installation holes of the wall mounting kit; Lock the wall mounting
kit to the wall;
Fig 3-6 Install the wall mounting kit
4. Install the device with the backplane to the mounting kit on the column and fix the
device and mounting kit together by using 4pcs short screws and 1pcs long screws.

DCWL-7962OT Outdoor AP
Installation Manual Chapter 3 AP Installation
3-6
Fig 3-7 Wall hanging installation of AP
3.5 Connect Cables
3.5.1 Connect Network Cables
The DCWL-7962OT (R5) outdoor AP supports the 802.3at PoE power. The power
and the network cables should be isolated with water. Please install the waterproof kit
onto the network cables as the sequence in the following figure.
Fig 3-8 The installation sequence of the waterproof kit
After installed, insert the cables into the AP and screw the waterproof kit as the
sequence.

DCWL-7962OT Outdoor AP
Installation Manual Chapter 3 AP Installation
3-7
Fig 3-9 Install the waterproof kit
3.5.2 Connect Ground Cables
Please install the ground cables onto the ground point.
3.5.3 Connect RF Cables
Please install the RF cables or antenna onto the RF interface. The cables interface
cannot be installed with a mistake. The 5G cable should be connected in the 5G RF
interface and the 2.4G cable should be connected in the 2.4G RF interface. After
connection, wrap 3 layers of waterproof tape on the connection point. The waterproof tape
should be elongated first to make its width turn into the half of the original width; and then
wrap it.
Fig 3-10 Install the antenna

DCWL-7962OT Outdoor AP
Installation Manual Chapter 3 AP Installation
3-8
3.6 AP Power
3.6.1 Checking before Power
After installing the AP, user should check it before power every time as below:
When AP use the 802.3at standard PoE power, please ensure the power is
connected normally to ground.
3.6.2 PoE Power
User can use the Ethernet cable to connect the Ethernet interface of the AP and the
switch which supports PoE function to power to the AP.
3.6.3 Checking after Power
Check if the LED of AP works normally after connecting the power. The explanation of
LED status is seen in the product spec.
3.7 Connect AP to Internet
In the actual use, AP can be uplink connected to the Internet or MAN through the
Ethernet port. Connect the Ethernet port of the AP to the switch port to achieve the uplink
connection.

DCWL-7962OT 室外型无线接入点产品安装指导 目录
1
目录
第1章设备简介......................................................................1-1
第2章安装准备......................................................................2-1
2.1 安全注意事项....................................................................................2-1
2.2 检查安装条件....................................................................................2-1
2.3 设备附件...........................................................................................2-1
2.4 安装工具...........................................................................................2-2
第3章安装 AP.......................................................................3-1
3.1 安装流程...........................................................................................3-1
3.2 安装前检查 .......................................................................................3-2
3.3 确定安装位置....................................................................................3-2
3.4 安装 DCWL-7962OT(R5) .................................................................3-2
3.4.1 抱柱安装方式 .........................................................................................3-2
3.4.2 壁挂安装方式 .........................................................................................3-4
3.5 连接线缆...........................................................................................3-6
3.5.1 连接网线.................................................................................................3-6
3.5.2 连接接地线 .............................................................................................3-6
3.5.3 连接射频线 .............................................................................................3-6
3.6AP 供电 ............................................................................................3-7
3.6.1 上电前检查 .............................................................................................3-7
3.6.2 PoE 供电.................................................................................................3-7
3.6.3 上电后检查 .............................................................................................3-7
3.7 将AP 连接到网络.............................................................................3-8

DCWL-7962OT 室外型无线接入点产品安装指导 第1章设备简介
1-1
第1章设备简介
DCWL-7962OT(R5)室外型无线接入点产品如下图：
图1-1 DCWL-7962OT（R5）AP
DCWL-7962OT 室外型 AP 端口说明如下表。
表1-1 产品端口说明列表
序号 名称 说明

DCWL-7962OT 室外型无线接入点产品安装指导 第1章设备简介
1-2
1 5G-1 5G的天线接口1
2
5G-2 5G的天线接口2
3 2.4G-1 2.4G的天线接口1
4 2.4G-2 2.4G的天线接口2
5 PoE PoE接口，PoE供电和以太网接口
6 GND 接地点
7 Reset AP复位孔
DCWL-7962OT 室外型 AP 基本配置如下表。
表1-2 产品基本配置列表
产品型号 产品适用协议和特点 天线 最大功耗
DCWL-7962OT(R5) • IEEE802.11a/b/g/n
• 双射频
另配外置天线 24W
DCWL-7962OT 室外型 AP 的外形尺寸及重量如下表。
表1-3 外形尺寸及重量
产品型号 外形尺寸 重量
DCWL-7962OT(R5)（W × D × H）220 × 220 × 100mm 3.80kg

DCWL-7962OT 室外型无线接入点产品安装指导 第2章安装准备
2-1
第2章安装准备
2.1 安全注意事项
仅允许专业人员进行设备及其附件的安装和拆卸工作，进行安装和操作前必须仔细阅读
设备提供的相关安全介绍。
采取适当的安全措施避免人身伤害和设备损坏。
请将设备放置在干燥、平整的地方，并且做好防滑措施。
保持设备洁净无灰尘。
请不要将设备和安装工具放在行走区域内。
2.2 检查安装条件
在准备安装之前，还应该对设备的安装条件进行检查，以保证设备长期处于良好的运行
环境之中。 可从以下方面对安装条件进行检查。
设备工作的温度、湿度环境要求如下：
表2-1 设备工作温度、湿度指标
项目 取值范围
标准工作环境温度（室外） -40℃～60℃
存储温度 -45℃～70℃
工作湿度（非凝露） 5%～95%
2.3 设备附件
DCWL-7962OT(R5) 室外型 AP 随机发货的附件参考装箱清单。

DCWL-7962OT 室外型无线接入点产品安装指导 第2章安装准备
2-2
2.4 安装工具
在安装 DCWL-7962OT(R5)室外型 AP 时，可能需要用到下列的工具（以下工具需要
用户自备）。
水平尺 记号笔 小刀 剥线钳 网线钳
冲击钻（1个）以
及配套钻头
若干
橡胶锤 十字螺丝刀 梯子

DCWL-7962OT 室外型无线接入点产品安装指导 第3章安装 AP
3-1
第3章安装 AP
由于 DCWL-7962OT(R5)室外型 AP 的安装位置通常较高，AP 安装好后维护人员无法
通过 Console口登录设备进行维护和调试，所以建议用户在把 AP设备安装到指定位置之前，
根据客户需求，进行相关基础配置。
3.1 安装流程
图3-1 AP 设备安装流程图