Yutrax TX210 User manual

Operator's Manual
TX210
UTV Jump Seat
OMTX210
Rev. Date 9/17/10
© 2010 Ardisam, Inc.
All Rights Reserved.

Owner's Manual
TX210 UTV Jump Seat
Check for parts online at www.yutrax.com or call 800-345-6007 M-F 8-5 CST
Owner's Manual
TX210 UTV Jump Seat
Check for parts online at www.yutrax.com or call 800-345-6007 M-F 8-5 CST
Yutrax oers a full line of Engineered Outdoor Gear. We appreciate your
purchase of our world class UTV Jump Seat. Follow these few simple in-
structions and your product will be sure to give you many years of trouble
free pleasure. Instructions should be kept in a safe place and reviewed at
least annually.
If for any reason you have a problem with your product, DO NOT return to
the retailer, contact the Yutrax customer service department M-F from 8
a.m. to 5 p.m. at 800-345-6007 for assistance.
ASSEMBLY INSTRUCTIONS:
Tools needed – two 7/16” wrenches, two 1/2”wrenches, 21/64" drill bit
IMPORTANT ASSEMBLY TIP: Do not tighten any nut and bolt com-
binations completely until all parts are assembled together! Finger
tighten plus one turn of a wrench only! This will temporarily hold
the lock nut on the bolt while helping alignment of all parts! After
all parts are assembled together, all nut & bolt combinations can
be completely tightened.
NOTE: This UTV Jump Seat was universally designed to t most
brands of UTV’s.
1. Study and measure the width of your UTV box. This UTV Jump Seat has
been designed to t most brands of UTV’s. The upright frames (A682)
can be mounted at 26”, 28”or 30”widths. DO NOT tighten all nut & bolt
assemblies completely!
NOTE: There are multiple hole locations in backrest frame, seat stop
tube and seat frame.
It all depends on the mounting positioning of Jump Seat in relation to
your UTV box. Study your UTV box to determine the best mounting
locations that will not interfere with any frame rails of the UTV.
2. Attach the backrest frame (A681) to the two upright frames using (4)
provided 1/4-20 x 2” hex head bolts, 1/4" steel washers, and locknuts.
SEE FIGURE 1A.
3. Attach the two seat belt receivers (48798) to the two upright frames using
(2) provided 5/16-18 x 1-3/4”hex head bolts, (6) 5/16" steel washers, and
locknuts. SEE FIGURE 1B. Receivers should both be mounted on what
would be the“outer”sides of the upright frames when unit is completely
assembled.
Figure 1A
locknuts
upright frames
backrest
frame
1/4-20 x 2” bolts
steel washers
Figure 1B
steel washers
locknut
5/16-18 x 1-3/4” bolt
seat belt receiver
upright frame
WARNING
READ, UNDERSTAND AND FOLLOW ALL ASSEMBLY, IN
SPECTION, MAINTENANCE & USE INSTRUCTIONS PRO
VIDED BEFORE EACH USE. FAILURE TO FOLLOW ALL
WARNINGS AND INSTRUCTIONS COULD RESULT IN SERI
OUS INJURY OR DEATH.
BE SURE TO FOLLOW ALL INSTRUCTIONS PROVIDED. IF
ANY INSTRUCTIONS ARE NOT UNDERSTOOD OR IF YOU
HAVE A PARTS ISSUE CALL 8003456007 BEFORE USING.
DOUBLE CHECK ASSEMBLY STEPS TO BE CERTAIN YOU
HAVE CORRECTLY ASSEMBLED THIS PRODUCT.

Owner's Manual
TX210 UTV Jump Seat
Check for parts online at www.yutrax.com or call 800-345-6007 M-F 8-5 CST
Figure 2A
Figure 3
4. Attach the seat stop tube (A684) to the top side of upright frames using (2)
provided 1/4-20 x 2-1/4”hex head bolts, locknuts and 1/4”steel washers.
SEE FIGURE 2A .
5. Attach the two seat pivot tubes (A683) to the“inside”of the upright frames
using (2) provided 1/4-20 x 2-1/2” hex head bolts, locknuts and (6) 1/4”
steel washers. SEE FIGURE 2B.
6. Attach the seat frame (A678), mesh side up, to the top of previously
mounted seat pivots using (4) provided 1/4-20 x 2-1/4” hex head bolts,
locknuts and 1/4” steel washers. SEE FIGURE 2B.
NOTE: Mount the seat frame so the hole in the side of frame are towards
the front of the unit, away from the backrest.
7. Attach the two armrests (A685) to the outside of backrest frame using (2)
provided 1/4-20 x 2”hex head bolts, locknuts and (4) 1/4” steel washers.
SEE FIGURE 3.
NOTE: Mount the longer side of armrests to the backrest.
8. Place spring lock pin through each armrest, into the seat frame and
securely latch. You may now tighten all nut & bolt assemblies. Be sure
not to over tighten or crush tubing when tightening!
steel washers
locknuts
1/4-20 x 2-1/4” bolts
Figure 2B
steel washers
locknuts
1/4-20 x 2-1/2” bolts
1/4-20 x 2-1/4” bolts
steel washers
locknuts
1/4-20 x 2” bolts
steel washers
locknuts
spring lock pins
seat stop tube
upright frames
upright frames
seat pivot tubes
seat frame
armrests
steel washers
WARNING
BE CERTAIN SPRING LOCK PINS ARE LATCHED TO PREVENT
ACCIDENTAL REMOVAL.
BE SURETO PERIODICALLY CHECK ALL NUT AND BOLTS FOR
TIGHTNESS. OVER TIME, NUTS AND BOLTS MAY BECOME
LOOSE FROM VIBRATION.
BE SURE YOUR SLIP KNOT IS CORRECTLY AND SECURELY
ATTACHED.
NEVER MOUNT THE JUMP SEAT TO THE REAR OF THE UTV
BED, NEARTHETAILGATE. ALWAYS MOUNT ITTOTHE FRONT
END OF UTV BED, FACING THE REAR OF THE UTV WITH
BACKREST AGAINST UTV CAB.

Owner's Manual
TX210 UTV Jump Seat
Check for parts online at www.yutrax.com or call 800-345-6007 M-F 8-5 CST
Owner's Manual
TX210 UTV Jump Seat
Check for parts online at www.yutrax.com or call 800-345-6007 M-F 8-5 CST
Figure 4A
Figure 5
9. Attach the seat belt strap (48815) to the seat stop tube by wrapping
around the seat stop tube, forming a loop, and threading both ends of
the seat belt strap through the loop. Pull each end of the strap tight. This
action forms a slip knot, which should be made in the center of the seat
belt strap.This permanently attaches the seat belt strap to the Jump Seat.
You may temporarily buckle the male ends to the seat belt receivers. SEE
FIGURES 4A & 4B.
10. Attach the two mounting channels (A686) to the bottoms of upright
frames using (4) provided spring lock pins. SEE FIGURE 5. Be sure to latch
the lock pins securely. Place the assembled Jump Seat with channels
attached into the bed of the UTV. With the Jump Seat facing the back of
the vehicle, and backrest against the cab of UTV, mark the 4 locations
to drill holes for permanent attachment of the channels. Remove Jump
Seat after hole locations are marked.
11. Using a 21/64”drill bit, drill the 4 marked locations in the bed of UTV.
12. Attach the mounting channels to the UTV bed using (4) provided 5/16-
18 x 1” or 5/16-18 x 1-1/4” or 5/16-18 x 1-3/4” hex head bolts, 5/16” steel
washers, large fender washers and locknuts. SEE FIGURE 5. Tighten
securely! Reattach the Jump Seat to the channels using the provided
spring lock pins.
large fender washers
locknuts
5/16-18 x 1” or 1-1/4" or
1-3/4” bolts
mounting channels
spring lock pins
steel washers
upright frames
Figure 4B
WARNING
NEVER ATTACH THE JUMP SEAT FACING FORWARD,
TOWARDS THE CAB. ALWAYS MOUNT IT FACING THE REAR
OF THE UTV.
BE CERTAIN SPRING LOCK PINS ARE LATCHED TO PREVENT
ACCIDENTAL REMOVAL.
NEVER USE THE JUMP SEAT WITH OUT THE SAFETY CAM
STRAPS SECURED CORRECTLY.
TEST THE STRAPS TO BE SURE YOU HAVE THREADED THE
STRAP THROUGH THE CAM BUCKLE IN THE CORRECT
DIRECTION.
DOUBLE CHECK TO BE SURE LATCH ON TILT BED OF UTV
IS SECURED CORRECTLY. NEVER UNLOCK THE BED LATCH
WHILE PASSENGERS ARE SEATED ON JUMP SEAT.

Owner's Manual
TX210 UTV Jump Seat
Check for parts online at www.yutrax.com or call 800-345-6007 M-F 8-5 CST
Figure 6
13. a.With entire unit xed to the UTV, secure the Jump Seat to the UTV frame
using the (2) safety cam straps (48851) provided. Wrap the loop end of
the short strap around the upright frame, just below the welded joint.
Thread the cam buckle through the sewn loop and pull tight forming a
slip knot.This action makes it permanently attached. Repeat for opposite
side of Jump Seat.
b.Wrap the loop end of the long strap around the frame of the UTV. Thread
the long tail through the sewn loop and pull tight forming a slip knot.
This action makes it permanently attached.This strap must be attached in
an area where the strap will not slide. It must be able to be attached and
stay in a stationary location. SEE FIGURE 6 FOR POSSIBLE MOUNTING
LOCATION. Repeat for opposite side of Jump Seat.
c. Thread the long strap through the cam buckle by pressing lever and
pulling through. Pull the long strap tight. Repeat for opposite strap.
This is a safety feature to keep the UTV bed down incase it becomes
unlatched.
14. Attach the padded seat to the top side of seat frame and snap the side
release buckles together. Pull straps tight so seat is not loose. Attach
padded backrest to backrest frame and secure with Velcro.
15. You will nd a side release buckle with a short strap and long strap
sewn to it. Take the short strap and wrap the loop end of strap around
the rim of the seat frame (center of the front side). Thread the release
buckle through the sewn loop and pull tight forming a slip knot. This
action makes it permanently attached. Do the same for the long strap,
by attaching it to the center of bottom rail on backrest frame. Pull the
strap tight. This feature secures the seat in the ip up position if desired.
SEE FIGURE 7.
NOTE: In order to ip seat up, you must remove the spring lock pins
from the armrests. Armrests will pivot back freely.
16. Attach the (2) provided 9”arm pads to the armrests by wrapping around
tubing and securing Velcro together.
safety cam straps
UTV frame
Figure 7
WARNING
NEVER USE IN EXCESS OF 10 MPH WHILE PASSENGERS ARE
RIDING IN THIS UTV JUMP SEAT. WHEN PASSENGERS ARE
IN THE UTV JUMP SEAT, YOU SHOULD ONLY USE YOUR UTV
FOR TRAIL RIDING, NOT HIGH SPEEDS.
RIDERS MUST BE 18 YEARS OF AGE OR OLDER.
NEVER DRIVE ON UNEVEN TERRAIN. WEIGHT LOADS CAN
SHIFT CAUSING YOU TO LOOSE CONTROL OF YOUR UTV.
DRIVE ON LEVEL TERRAIN ONLY.

Owner's Manual
TX210 UTV Jump Seat
Check for parts online at www.yutrax.com or call 800-345-6007 M-F 8-5 CST
Owner's Manual
TX210 UTV Jump Seat
Check for parts online at www.yutrax.com or call 800-345-6007 M-F 8-5 CST
JUMP SEAT PARTS
10
2
11
17
8 9
7
17
20
3
12
4
13
1
6
5
13
18
14
16
21
22
23
23

Owner's Manual
TX210 UTV Jump Seat
Check for parts online at www.yutrax.com or call 800-345-6007 M-F 8-5 CST
WARRANTY
Yutrax, a division of Ardisam Incorporated, oers a one year limited
warranty to be free from defects in materials and workmanship for
the service life of the product, not to exceed twelve consecutive
months from the date of purchase. This warranty applies to the
original owner with a proof of purchase and is not transferable.
This warranty applies only to products which have not been
subjected to negligent use, misuse, alteration, accident or if repairs
have been made by anyone outside our factory. This warranty
supersedes all other warranties either expressed or implied and
all other obligations or liabilities on our part. Ardisam, Inc., does
not assume, and does not authorize any other person to assume
for us, any liability in connection with the sale of our products.
Warranty work must be sent directly to Ardisam, Inc. or one of
our authorized service centers and performed by them. To obtain
warranty service and/or replacement instructions, you must have
prior approval from Ardisam, Inc. before shipping your package to
us by calling our customer service department at 800-345-6007 or by
writing to: Ardisam, Inc., P.O. Box 666, 1690 Elm Street, Cumberland,
WI 54829 for a return material authorization number (RMA#). All
items must be shipped prepaid. Ardisam, Inc. will at no charge,
repair or replace, at their discretion, any defective part which falls
under the conditions stated above. Ardisam retains the right to
change models, specications and price without notice.
For replacement parts, phone [phone]
or go online to www.GetYukonTracks.com.
ALWAYS…
• Use as a UTV Jump Seat only.
• Inspect before each & every use to be sure there is no product
damage or loose/missing bolts & hardware.
• Keep body extremities inside of UTV bed.
• Wear seat belts while seated in the jump seat.
NEVER…
• Use a damaged UTV Jump Seat.
• Drive in excess of 10 MPH while passengers are in this UTV
Jump Seat. Only use for trail riding when passengers are in UTV
Jump Seat.
• Drive on hilly terrain- weight loads can shift.
• Attach the Jump Seat facing forward, towards the cab. Always
mount it facing the rear of the cab.
• Mount the Jump Seat to the rear of the UTV bed, near the
tailgate. Always mount it to the front end of UTV bed, facing
the rear of the UTV with backrest against UTV cab.
• Use when intoxicated or using over-the counter medication or
prescription drugs.
• Use more than two passengers.
• Use carelessly- Think Safety!
KEY # PART # DESCRIPTION QTY.
1 A682 UPRIGHT FRAME 2
2 A681 BACKREST FRAME 1
3 A684 SEAT STOP 1
4 A683 PIVOT SEAT 2
5 A678 SEAT FRAME 1
6 A686 CHANNEL MOUNT 2
7 A685 ARM REST 2
8 48798 RECEIVER, SEAT BELT 2
9 48261B WASHER, BLK 1/4" 20
10 48752B NUT, FLANGED, TOP LOCK 1/420 14
11 48153B BOLT 1/4-20 X 2 HHCS BLK ZN P-T 6
12 48271B BOLT, HHCS, GR5 BLK
1/420 X 21/4"
6
13 48017 SPRING LOCKPIN, ROUNDED
RETAINER 1/4 X 2"
6
14 1401B BOLT, HHCS GR5 BLK
5/1618 X 11/4"
4
15 1921333 BOLT, HHCS GR5 5/1618 X 1" 4
16 48753B NUT, HEX FLANGED TOP LOCK
BLK 5/1618
6
17 WF516B WASHER, FLAT 5/16" STANDARD 10
18 1960044 WASHER, FLAT
.33 ID X 1.25 OD X .07 THK
4
19 48270B BOLT, HHCS GR5 BLK
1/420 X 21/2"
2
20 8655B BOLT, HH BLK 5/16-18 X 1-3/4" 6
21 200302 SEAT, PADDED 1
22 200303 BACKREST, PADDED 1
23 200304 ARMREST PADDED BLACK 9” 2
 48815 SEAT BELT STRAP 1
 48851 SAFETY CAM STRAP 2
 48828 STRAP ASSEMBLY, FEMALE 1
 48829 STRAP ASSEMBLY, MALE 1
JUMP SEAT PARTS LIST

Check for parts online at www.yutrax.com or call 800-345-6007 M-F 8-5 CST
YUTRAX™, Division of Ardisam, Inc.
1160 8th Avenue, PO Box 666
Cumberland, WI 54829
800-345-6007 | Fax [phone]
Email: [e-mail]