Zebra-Tech MEASURING BOARD User manual

MEASURING BOARD
OPERATION MANUAL
H/S
Drw Number
3.2 Ra UNLESS SPECIFIED
of
Part / Assem Description
Rev DATE
Material
TOLERANCE UNLESS SPECIFIED
Part Number
*DO NOT SCALE / IF IN DOUBT ASK*
DRW Sheet
SURFACE FINISH
*THIS INFORMATION IS THE PROPERTY OF ZEBRA-TECH LTD. ALL RIGHTS RESERVED.*
*BREAK ALL EDGES UNLESS SPECIFIED*
DESCRIPTION Scale REV
*ALL UNITS IN MM/DEGREES UNLESS SPECIFIED*
CHK
Linear Angular
0.000
`0.005 `0.005
0.00
`0.01 `0.01
0.0
`0.1 `0.1
0
`0.5 `0.5
English. 11/2016.V1.20

TABLE OF CONTENTS
1. Introduction.......................................................................... 3
2. Operation............................................................................. 4
Overview...................................................................................................... 4
Mode options...............................................................................................5
3. Menu.................................................................................... 7
Menu system................................................................................................7
Delete last entry........................................................................................... 7
Tare...............................................................................................................7
Enable bluetooth..........................................................................................8
Clear storage................................................................................................8
Status...........................................................................................................8
Config...........................................................................................................9
4. Data recording.....................................................................10
5. Maintenance........................................................................11
6. Battery replacement............................................................12
Logger batteries..........................................................................................12
Button battery............................................................................................. 12
7. Specifications......................................................................13
8. Mobile application...............................................................14
Overview..................................................................................................... 14
Mobile configuration................................................................................... 15
9. Overall dimensions..............................................................16
10. Further assistance.............................................................17

The Zebra-Tech Measuring Board is a tough portable battery
powered device that is designed to take measurements of objects
and organisms in harsh environments.
The measurements are logged internally and then downloaded to a
mobile device using the Zebra-Tech app. The measurement can
also be transmitted wirelessly to the Zebra-Tech Deck Logger for
logging in real time.
The Measuring Board has been specifically designed to operate in
wet and muddy conditions. It is ideal for field measurements of
shellfish, fish and other organisms.
A range of user select operating modes are available which enables
a variety of measurement methods. For example; logging 2 distinct
species, or making length and width measurements.
3
1. INTRODUCTION

OVERVIEW
The Measuring Board is fully splash proof but it should not be
completely submerged underwater.
To switch on simply slide the moving jaw. The Measuring Board will
automatically shut down after 1 minute of inactivity (no jaw
movement or button press).
There are two buttons which each have a different function
depending on the operating mode.
If the wireless link with the Zebra-Tech Deck Logger is to be used,
the Deck Logger needs to be configured so that it will pair with
your unique Measuring Board. Please refer to your "Deck Logger
Custom Application Manual" for details on how to do this.
2. OPERATION
4
Item Number Quantity Description Part Number Comment
1 1 MB Bed P-00380-M201 Machined
2 1 MB Base P-003 0-M000 Machined
4 2 MB Rail P-00388-M100 Machined
5 1 MB Rail Plate Floating P-00404-M100 Machined
6 1 MB Bed Plate P-00386-M100 Laser cut
7 1 Measuring Board Fixed Jaw Assembly MB-04 Approved for construction
8 1 MB Moving Jaw Assembly MB-050 Approved for construction
4 M8 X 25 316 CHEESE SLOT M/SCREW Slot / SMCHM608025 / 316SS Anzor
11 2 M4 X 20 316 DOWEL PIN Dowel / DPM604020 / 316SS Anzor
12 2 M5 X 8 316 CSK SOCKET SCREW CSK / SSHCKM605008 / 316SS Anzor
13 1 M8 X 30 316 BUTTON SOCKET SCREW Button / SSHBM608030 / 316SS Anzor
14 2 M6 X 12 316 BUTTON SOCKET SCREW
Button Head / SSHBM606012 / 316SS
Anzor
15 4 4 guage by quarter 316 Pan Pozi Self Tap Not on Anzor ?????
16 1 O ring 4. 7 x 1.78 044 N70 Seal Imports
17 1 300mm Magneto Pot MP1-L-0300-103-5%-RH DigiKey
18 1 Battery Holder 2xAA Add Part # Keystone
1 1 MB Battery Sticker P-00603-M000 Sportswise S&G
20 1 MB Rope Handle P-00383-M000 Burnsco
21 12 M5 X 16 316 PAN SLOT M/SCREW Slot / SMPM605016 / 316SS Anzor
22 1 MB Tube Handle P-003 7-M000 Fluid Power Solutions
23 1 MB Rail Plate Fixed P-00403-M100 Machined
SURFACE FINISH
2
Part / Assem Description
Part Number
CHK
3.2 Ra UNLESS SPECIFIED
Material
Scale
H/S
Sheet
Drw Number
0
DATE
*THIS INFORMATION IS THE PROPERTY OF ZEBRA-TECH LTD. ALL RIGHTS RESERVED.*
2
*DO NOT SCALE / IF IN DOUBT ASK*
TOLERANCE UNLESS SPECIFIED
*ALL UNITS IN MM/DEGREES UNLESS SPECIFIED*
DESCRIPTION DRW Rev
*BREAK ALL EDGES UNLESS SPECIFIED*
REV of
MB-038
MB-038-C
Measuring Board General Assembly
Approved for construction
2
9/08/2016
H
2
Various improvements 09/08/2016
H H/J/S/Z
1
Stainless Mounts added 05/05/2016
H H/J/S/Z
Linear Angular
0.000
`0.005 `0.005
0.00
`0.01 `0.01
0.0
`0.1 `0.1
0
`0.5 `0.5
Function
buttons

MODE OPTIONS
•Mode 1
This is for logging the measurement made by each single A or B
button press. The button ID associated with the measurement is
recorded in the data file.
Example: Two species of shellfish could be measured with a button
assigned to each species.
•Mode 2
This requires 2 button presses to occur in a fixed sequence –A
followed by B. The data is not logged or transmitted until both
measurements have been made.
Example: The length and width of a shellfish could be measured
with length assigned to button A and width assigned to button B.
•Mode 3
This requires 3 button presses to occur in an A,B,B sequence. The
data is not logged or transmitted until all 3 measurements have
been made.
Example: The length,width and height of a shellfish could be
measured with length assigned to button A , width assigned to
button B first press and height assigned to button B second press.
5

•Mode 4
This mode enables button presses to be used to increment a
secondary manual measurement following the jaw measurement. It
can be used in 2 ways;
1) If no additional secondary measurement is required, simply press
button A.
2) If a secondary measurement is required, button B is pressed (jaw
measurement is logged) and then subsequent button B presses
increment the secondary measurement. Pressing A then logs both
measurements.
Example: The length of mussels are being measured by pressing
button B, which saves the measurement. The visual quality of the
mussels are being rated on a scale of 1 to 3. Pressing button B
again will increment the value required. Pressing button A will then
log the initial length measurement and the number chosen to
represent visual quality. Note that the manually chosen value is
arbitary. It could represent a measurement such as an estimation of
Abalone hump size or a general value such as in the above
example.
6

7
MENU SYSTEM
To enter the menu system both buttons must be pressed
simultaneously while the Measuring Board is turned on.
The menu is navigated by pressing the A button if the current menu
option is required, or the B button to advance onto the next menu
option.
DELETE LAST ENTRY
Selecting this causes the last logged measurement to be deleted
from the on-board data storage.
Note that the measurement is not deleted if it has
already been transmitted to a nearby Zebra-Tech Deck
Logger.
TARE
This zero’s the sliding jaw measurement. Before selecting Tare,
ensure that the jaws are pushed together.
3. MENU

8
ENABLE BLUETOOTH
Data stored on the Measuring Board can be offloaded to an
Android device using the Zebra-Tech app. Please refer to the
Mobile application section for details. Select "Enable Bluetooth"
whenever data is to be offloaded using the app.
CLEAR STORAGE
This deletes all the data in the on-board storage.
STATUS
•SN: The Measuring Board’s individual serial number which will
match the serial number etched on the bed.
•Store: Amount of available data storage.
•Ver: Current firmware version number.
•Batt: Internal battery voltage.

CONFIG
Selecting this enables the configuration setup menu to be
accessed.
•Measuring mode
Mode 1 to 4 can be selected –refer to description above.
•Set time
When selected, the internal clock time and date can be set. This is
done by pressing button A to select the field to adjust, then sliding
the movable jaw until the correct value is displayed, then setting by
pressing button A. Fields can be skipped by pressing button B.
•Units
The units displayed can be set to mm, inch or raw. Note that
regardless of the selected units, the logged data is always mm.
•Exit
Return to normal operation.
9

The Measuring Board logs all measurements in its internal
non-volatile data storage. This data is retained even if the battery
goes flat. There is sufficient capacity to store 10,000 single
measurements or 5,000 double measurements.
Each measurement is logged with the time and date and also the
button number that was pressed to trigger the measurement.
The user is alerted if the data memory becomes full. No further
measurements are possible until the data is deleted.
Data can be offloaded using the Zebra-Tech mobile application –
available for Android. See Mobile application section.
Measurement data is also wirelessly transmitted every time a
measurement is made. If a Zebra-Tech Deck Logger is nearby it will
display and log the Measuring Board data if it has been configured
to pair with the Measuring Board.
1 0
4. DATA RECORDING