Zempire NEO Series User manual

NEO SERIES
O
NE
10
EQUIPMENT
CAMPING
For a detailed description of all the features and specifi cations
of this product please visit our website.
Tested in New Zealand. Made with care in China
Care Instructions
1. Ensure guy ropes are out at all times during use
2. Never pack your tent away wet. If you must take your tent down when wet, ensure that it is dried
completely as soon as possible to prevent mildew forming
3. If mildew does form on your tent, wash off with warm water and a soft brush to prevent further growth,
do not use soap or detergents
4. Do not use an open fl ame inside your tent. The fabric has been treated with a fi re retardant but is in no
way fi re proof
5. Clean all pegs and poles before storing
6. This tent is not designed to withstand storm conditions. During strong winds, it is recommended that the
tent be taken down
7. Do not leave your tent pitched unnecessarily for extended periods of time, UV light damages the fl y and
will shorten the life of your tent
Condensation
It is important that lower vents are opened at all times to reduce the risk of condensation. During humid or damp
conditions, it is recommended that inner door cover is opened to expose the mesh layer to allow additional
airfl ow throughout your tent.
Do not use foam swabs or non bonded mats directly on the tent fl oor. This will cause condensation between the
mat and fl oor and if not dried out can lead to mildew forming.
2 Year Tent Guarantee
Please take time to read about the protection we off er you
All our tents come with a guarantee designed to protect you as our valued customer. Flow Imports Ltd, the
makers of Zempire Camping Equipment tents, will repair or replace this tent, at their discretion, should it fail due
to faulty materials or manufacture for a period of 2 years from the date of sale.
The Guarantee is subject to the following conditions:
1. The Guarantee only applies to an original purchaser who purchased this tent from an approved retail
outlet
2. The Guarantee does not apply if the tent has been used for anything other than reasonable personal
camping use. Commercial use (e.g. rental) or continuous use as a residence are expressly excluded
3. Damage due to normal wear and tear, accident, acts of God, negligence (other than by Flow Imports Ltd),
failure by the purchaser to ensure instructions for setting up and care are observed, deterioration due to
abnormal exposure to ultraviolet light, insect or mildew attack, or any other cause reasonably beyond the
control of Flow Imports Ltd are not covered
4. If redress is sought under the terms of this Guarantee, then the tent must be returned by the purchaser to
the outlet from where it was purchased within the Guarantee period, in a clean, dry state and with proof
of purchase
5. All transport costs and any other indirect costs are excluded from the Guarantee.
6. Flow Imports Ltd reserves the right to make a reasonable charge for repairs which it determines are not
within the scope of the Guarantee
7. The Guarantee does not limit, modify or exclude any rights under any law if doing so would contravene
that law or make any part of this Guarantee invalid. However, Flow Imports Ltd:
a) excludes (to the extent permitted by applicable law) all conditions and warranties that might otherwise
be implied; and
b) limits its liability for breach of any such condition or Guarantee that it cannot exclude together with its
liability under the Guarantee, to repairing or replacing the Goods or paying the cost of having the Goods
repaired or replaced (at Flow Imports’ option).
This tent has been made with meticulous care and attention to detail. Providing it’s properly looked after and
correctly stored, it will help you enjoy all that nature has to off er for years to come.
Get out more - you owe it to yourself.

7. Pull the fly over the inner tent. The
Zempire logo should be at the front
and rear of the tent. Connect the
velcro loops inside the fly around the
cut outs on the corresponding pole
sleeve.
6. Peg out all the peg points
around the inner tent. The peg
points at the base of each pole
should be pegged through the
webbing loop rather than the
ring.
2x
2x
2x
4. Thread the GREEN poles through the
pole sleeve on either side of the central
dome. The repeat with the YELLOW
poles at each end of the tent. Insert the
pole ends into the pin located below
each pole sleeve.
8. Attach the elastic loop over the
existing inner pegs. Where there is
no existing peg, peg the fly directly
into the ground ensuring there is
significant space between the inner
and fly.
9. It is recommended that guy ropes are
pegged out at all times and windows
are opened whenever possible to allow
adequate ventilation. Try to have the
guy ropes at 45 angle to the ground.
3. Thread the RED poles through the
pole sleeves that run diagonally across
the center of the tent. Insert the ends
of the poles into the pin located below
each pole sleeve. Attach the C Clips
onto the poles.
1. Clear your site making sure there are no
sharp objects where you are going to pitch
your tent. Try to get a site that is as flat as
possible. Lay out the inner (white) tent, the
round door is located at the front and rear.
The tent is symmetrical.
2x
2. Assemble the 8 pole sections. Ensure
that the poles are inserted fully into the
steel connectors. It is important that the
poles are fully inserted into the ferrules.
If not connected correctly they can
cause damage when tensioned.
5. Thread the BLUE poles through the
pole sleeve at the front and rear of the
tent. Insert the pole ends into the pin
located below each pole sleeve.
steel ring.
Insert the pole
ends into the pins located on the steel
rings at the base of the tent. Attached
the c-clips around the poles.
Insert
the pole ends into the pins located on
the steel rings at the base of the tent.
Attached the c-clips around the poles.
5. Thread the BLUE poles through the
pole sleeve at the front and rear of
the tent. Insert the pole ends into the
pins located on the steel rings at the
base of the tent. Attached the c-clips
around the poles.