ZENEC Z-E6150 User manual

1
Z-E6150
INSTALLATION MANUAL
EN

22
COMPATIBILITY LIST
1. Ifyourvehiclehasabasicfactory-tted
radio(similartotheonepicturedhere),
youneedtoacquireasuitableToyota
coverforyourvehiclebeforeyoucan
installyourZ-E6150.
2. Ifyourvehiclehasahigh-quality
factory-ttedradio(asshownhere
H=100mm,B=200mm),youcan
easilyswaptoaZ-E6150.
1 2
NOTE
● Theinformationinthecompatibilitylistissubjecttocorrection.Dependingontheequipmentttedin
yourvehicle,youmayrequireanadditionaloriginalToyotacover.Theseareavailableonlineorfromyour
Toyotadealer.
ThefollowingsectionshowshowtotellthedifferenceonthebasisofaToyotaAvensis3G(TypeT27).
Manufacturer Model Model type Model year
Toyota Auris 1GTypeE150 2006–2012
Toyota Avensis 1GTypeT22 2001–2003
Toyota Avensis 2GTypeT25 2003–2009
Toyota Avensis 3GTypeT27 2009–2015
Toyota AvensisVerso – 2001–2005
Toyota Camry 5GTypeXV30 2001–2006
Toyota Celica 7GTypeT23 1999–2005
Toyota Corolla 9GTypeE120 2001–2007
Toyota Corolla 10GTypeE14/15 2007–2013
Toyota CorollaVerso 2GTypeZER/ZZE 2004–2009
Toyota GT86 – from2012
Toyota Hilux 7GTypeT25 2005–2015
Toyota Previa/Estima 2GTypeXR30/XR40 2000–2006
Toyota RAV4 2GTypeACA20/21ZCA25/26 2001–2006
Toyota RAV4 3GTypeCA30W 2006–2013
Toyota Ya r is 2GTypeXP9 2006–2011
Subaru BRZ – from2012

3
ATTENTION
● TheZENECsystemshouldbeinstalledbyanauthorisedretailer.Specicknowledgeandtoolsare
 requiredforinstallation.IncorrectinstallationcandamagethevehicleandtheZENECsystem.
● Fault-freeoperationcanonlybeguaranteedifyouusetheequipmentsupplied,ortheoptionalZENEC
originalaccessories.TheZENECsystemandoriginalaccessoriesmustneverbemodiedoralteredin
anyway.
IncorrecthandlingcandamagethevehicleandtheZENECsystem.
NOTE
● TheZENECZ-E6150isequippedwithanintegratedDAB+receiver.Touseit,youneedasuitableDAB
antenna(notsupplied),whichmustbeconnectedtotheZENECsystem.
● IfthetargetvehicleisttedwithanoriginalDABantenna,itcanstillbeusedinconjunctionwiththe
ZENECsystem.
● ZENECsystemsoftwareupdatesareinstalledusingaUSBdatastick.Youmustthereforeensure
thattheUSBconnectionontheZENECsystemremainsaccessibleduringinstallation(installationof
USBextension).
● IfyouhaveanyqueriesorproblemswiththeZENECsystem,pleasecontacttheretailerwhereyou
purchasedit.
SUPPLIED ITEMS
No. Item Quantity
1ZENECsystem 1
2MainpowercableforToyota 1
3 20-pincable(AUX-IN/SWC) 1
4 28-pincable(AUX-IN/SWC/Rev.) 1
5 24-pinconnectioncable(4.2,Cam,MZone,Mic) 1
No. Item Quantity
6 FMISOantennainterfaceforToyota 1
7 1mUSBextensioncable 1
8 Cableforhandbrakecontact 1
9 GPSantennawithcableandFakraplug 1
10 Mainunitmanual 1
TOOLS REQUIRED
●Ratchetwith10mmhexnut
●Cross-headscrewdriver(PhillipsPH2)
●Plasticlevertool
●Insulatingtape
OPTIONAL INSTALLATION ACCESSORIES
●DABantennawithSMBplug(e.g.Z-EACC-DAB1orZ-EACC-DAB2)
●Externalmicrophone(N-ZENC-MIC)

4
Example of installation: Toyota Avensis 3G (Type T27)
Disassembly and preparation:
NOTE
1. Removetheignitionkeyandleaveitoutsidethevehicleforthedurationofinstallation.
2. Startwiththeuninstallationoftheoriginalunit.
3. Donotswitchtheignitionbackonuntilallthepointsintheassemblymanualhavebeencompleted
andtheZENECsystemhasbeenfullyinstalled.
1. Levertheplasticcoverontherightofthecen-
treconsoleoutofitsxture,asshowninthe
diagram.Yourequireaplasticlevertoolforthis
step.
2. Levertheplasticcoverontheleftofthecentre
consoleoutofitsxture,asshowninthedia-
gram.Yourequireaplasticlevertoolforthis
step.
3. Tobeginwith,levertheradiocover/airventnoz-
zleupwardsoutofitsxture.Slidethelevertool
aroundtheplasticframeoncefromrighttoleft.
4. Removethelowersectionofthecoverfromits
xture.Thereisaconnectionforthehazardlight
switchontherearofthecover.Youmustdis-
connectthisbeforeremovingtheplasticframe
completely.
1
3
2
4

5
5. UnscrewandremovethefourPhillips(PH2)or
hex(10mm)screwsfromtheoriginalunit.
6. Carefullypulltheoriginalunitoutoftheradiobay.
Thenunplugallcablesontherearoftheunit.
7. Transfertheoriginalradiobrackets(leftand
right)toyourZENECsystem.
8. (Nopicture)
 InstalltheGPSantenna(No.9)inasuitable
position,makingsurethattheGPSreceptionis
notadverselyaffectedbyunwantedshieldingof
metallicvehicleparts(thermalinsulationglazing,
etc.).Thenroutetheconnectioncableintothe
radiobay.
9. (Nopicture)
 IfyouhavepurchasedtheoptionalexternalBlue-
toothmicrophone(N-ZENC-MIC),installitnow
andtheninserttheconnectioncableintotheradio
bay.Dependingonyourpreference,andwhether
youselectaninternalorexternalmicrophone,the
microphonesourceforBluetoothmodemustbe
setaccordinglyintheunitmenu.
10. (Nopicture)
 RoutetheUSBextensioncable(No.7)fromthe
radiobaytoyourpreferredposition.
Installation:
7
5
6

6
11. Connectthemainconnectioncable(No.2)ofthe
ZENECsystem(No.1)tothetworadioplugson
the vehicle.
 Dependingonyourvehicle,youmustuseeither
the20-pin(No.3)orthe28-pinconnector(No.4)
tooperatetheAUXconnectorandthesteering
wheelremotecontrol.Youmustconnecttheseto
themainconnectioncable.
 Thereversegearsignalissupportedonlybythe
28-pinconnector(No.4).Ifyourvehicleistted
witha20-pinconnector(No.3),youneedtouse
agaugetosearchforthereversegearsignaland
connectitdirectlytothemainconnectioncable
(No.2).
 IfyoucannotndanISOantennapluginyour
vehicle,itismostlikelythatyourvehicleisusing
aspecialToyotaantennaplug.Ifthisisthecase,
thesetincludesaFMISOantennainterface(No.
6)whichyoucansimplyconnecttotheoriginal
unit.Iftheantennaisactive,youmustalsocon-
nectthebluephantompowercabletothemain
connectioncable(No.2).
12. Removebothscrewsfromthetransportlock
priortoinstallingtheZENECsystem(No.1).
13. (Nopicture)
Connectallcablespreviouslyinstalledinthe
radiobaytotheZENECsystem(No.1).
14.Carefullyroutethevariousconnectioncablesof
theZENECsysteminthelowersectionofthe
radiobay.ThenslidetheZENECsystemcareful-
lyintotheradiobaybyapplyingcontrolledforce.
ScrewitbackintopositionwiththefourPhillips
(PH2)orhex(10mm)screws.
11
14
12

7
15. Youmustreattachtheradiocoveronceyou
havexedtheZENECsystembackintoposition.
Remembertoreconnecttheplugforthehazard
lightstotherearoftheradiocover.Tonishin-
stallation,simplyattachtheplasticcoverstothe
leftandrightofthecentreconsole.
NOTE
● Ensurethatalltheplugsontherearoftheunithavesufcientclearanceandarenotkinked.
● Anyplug-inconnectionswhichdonothaveasecuringmechanismmustalsobesecuredwith
insulatingtape.
STARTUP
Finally,carryoutageneralfunctiontestandperformthebasicsettingsandvehicle-specicsettings(steering
wheelremotecontrol,etc.).Alsomakesurethatnoerrormessagesaredisplayedinthevehicle.
15

8
F3
F2
F1
F
B24 B2
B23 B1
G
E14 E1
E28 E15
*
E
C6 C3
C2 C1
C
D20 D11
D10 D1
*
B
B4 B1
B10 B5
D
20PINCONNECTOR
(DEVICEBACKSIDE)
A1
A11
A10
A20
A
Z-E6150
DAB HDMI
USB 2
GPS
UKW/
FM
USB 1
CONNECTION DIAGRAM
USB1:
•AppleMFI
•USBMediaPlayback-SmartlinkDirect-SoftwareUpdates
USB2
•AppleMFI
•USBMediaPlayback-SmartlinkDirect-SoftwareUpdates
A1 N.A.
A2 Reverse
A3 KL15/Switched+12VPWR
A4 Illumination
A5 AnalogWheelKEY2
A6 AnalogWheelKEY1
A7 SpeakerRearLeft(-)
A8 SpeakerRearLeft(+)
A9 SpeakerFrontLeft(-)
A10 SpeakerFrontLeft(+)
D6 N.A.
D7 Reverse
D8 KL15/Switched+12VPWR
D15 AUXright
D16 AUXGND
D17 AUXleft
E1 AUXleft
E2 AUXGND
E3 AUXright
E6 AnalogWheelKEYGND
E7 AnalogWheelKEY2
E8 AnalogWheelKEY1
E27 Reverse
B1 RearMonitorOut
B2 FCameraIN
B3 RCameraIN
B4 VideoIN
B5 AUXINL
B6 AUXINR
B7 LineOutRearL
B8 LineOutRearR
B9 LineOutFrontL
B10 LineOutFrontR
B11 LineOutSubWoofer
B12 LineOutSubWoofer
B13 MIC
B14 FrontCamera12Vmax300mA
B15 IR/IN
B16 GND
B17 GND
B18 RearCamera12Vmax300mA
B19 N.A.
B20 N.A.
B21 N.A.
B22 N.A.
B23 N.A.
B24 N.A.
B1 SpeakerFrontRight(+)
B2 SpeakerFrontLeft(+)
B3 KL15/Switched+12VPWR
B4 KL30/Constant+12VPWR
B5 SpeakerFrontRight(-)
B6 SpeakerFrontLeft(-)
B7 KL31/PowerGND
B8 P.ANT
B9 N.A.
B10 Illumination
C1 SpeakerRearRight(+)
C2 SpeakerRearLeft(+)
C3 SpeakerRearRight(-)
C4 N.A.
C5 N.A.
C6 SpeakerRearLeft(-)
F1 P.ANT
F2 N.A.
F3 FMAntenna
A11 N.A.
A12 P.ANT+12V**(Antenna)
A13 P.CNTR+12V**(Amplier)
A14 Parking
A15 KL31/PowerGND
A16 KL30/Constant+12VPWR
A17 SpeakerRearRight(-)
A18 SpeakerRearRight(+)
A19 SpeakerFrontRight(-)
A20 SpeakerFrontRight(+)
**300mAmaxcurrent
*Connectionofthe20-pinor28-pin
plugdependsonvehicle
*
Connectionofthe20-pinor28-pin
plugdependsonvehicle
A
G

9
E D
AG
F
DAB
USB1
USB2
HDMI
28Pin 20Pin
P.ANT
B C
AUX-INR AUX-INL AUX-INR AUX-INL
Rev.
AnalogWheelKEY(KEY1/KEY2/GND)
B13 B12 B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 B1
B15
B14
B17 B16 B18
“E”or“D”con-
nectioncable
dependson
the vehicle!

Technicalmodificationsexcepted.Noliabilityforprintingerrors. ©Copyright2017·RevA/copydeadline:Q4-2017 ·English
ZENEC·Bohrturmweg1·CH-5330BadZurzach·Schweiz/Switzerland·Mail:[e-mail]·www.zenec.com