Zennio Presentia C v2 User manual

Presentia C v2
Presence Detector with Luminosity Sensor
for Ceiling Mounting
ZPDC30LV2
USER MANUAL
Application program version: [1.4]
User manual edition: [1.4]_b
www.zennio.com

Presentia C v2
https://www.zennio.com/ Technical Support: https://support.zennio.com/
2
CONTENTS
Contents........................................................................................................................................ 2
1 Introduction .......................................................................................................................... 3
1.1 Presentia C v2................................................................................................................ 4
1.2 Installation..................................................................................................................... 5
1.3 Start-Up and Power Loss............................................................................................... 6
2 Configuration......................................................................................................................... 7
2.1 General.......................................................................................................................... 7
2.2 Presence Detector......................................................................................................... 9
2.3 Logic Functions............................................................................................................ 10
ANNEX I. Communication Objects............................................................................................... 11

Presentia C v2
https://www.zennio.com/ Technical Support: https://support.zennio.com/
3
DOCUMENT UPDATES
Version
Changes
Page(s)
[1.4]_b
Changes in the document:
•Correction of error in the objects table.
-
[1.4]_a
Changes in the application program:
•Optimisation of Logic Functions and Presence
Detector modules.
-

Presentia C v2
https://www.zennio.com/ Technical Support: https://support.zennio.com/
4
1INTRODUCTION
1.1 PRESENTIA C v2
Presentia C v2 from Zennio is a device that aims at, among other functions, the
detection of presence, the measurement and control of the room luminosity and the
detection of occupancy within the room where it has been installed. It has been
designed for ceiling or false ceiling mounting by means of the bundled accessories.
The most outstanding features of Presentia C v2 are:
4 sensorswith configurable sensitivities.
4 LEDs to indicate motion.
Presence detection:
➢6 presence detection channels.
➢Luminosity-dependent presence detection (optional).
➢Periodic and delayed sendings (binary, scene, HVAC, percentage).
Occupancy detection:
➢1x occupancy detection channel.
➢Master / slave configuration.
➢Trigger upon door opening or closing.
➢Periodic and delayed sendings (binary, scene, HVAC, percentage).
Luminosity measurement:
➢Configurable correction factor and offset.
➢Periodic sending or upon value change.
2 constant light control channels with configurable setpoints.
10 customisable, multi-operation logic functions.
Heartbeat or periodic “still alive” notification.
Day / night configuration.

Presentia C v2
https://www.zennio.com/ Technical Support: https://support.zennio.com/
5
1.2 INSTALLATION
Presentia C v2 connects to the KNX bus through the on-board KNX connector.
Once the device is provided with power from the KNX bus, both the individual address
and the associated application program may be downloaded.
This device does not need any additional external power since it is entirely powered
through the KNX bus.
Figure 1. Presentia C v2. Elements
The main elements of the device are described next.
Programming button (5): a short press on this button sets the device into
the programming mode, making the associated LED (2) light in red.
Note: if this button is held while plugging the device into the KNX bus, the
device will enter the safe mode. In such case, the LED will blink in red every
0.5 seconds.
Detection notification LEDs (3): each of them emits a light flash whenever
the sensor associated to that zone observes motion.
1. Orientation marks.
2. Test/Prog. LED.
3. Detection notification LEDs.
4. Base.
5. Test/Prog. button.
6. Retaining spring.
7. KNX connector.

Presentia C v2
https://www.zennio.com/ Technical Support: https://support.zennio.com/
6
To get detailed information about the technical features of this device, as well as on the
installation process and on security procedures, please refer to the corresponding
Datasheet, bundled with the original packaging of the device and also available at
www.zennio.com.
1.3 START-UP AND POWER LOSS
During the start-up of the device, the Test/Prog. LED will blink in blue colour for one
minute before the motion sensors are ready.
Depending on the configuration, some specific actions will also be performed during
the start-up. For example, the integrator can set whether the detection channels should
start up enabled or disabled. Please consult the next sections of this document for
further details.
On the other hand, when a bus power failure takes place, the device will interrupt any
pending actions, and will save its state so it can be recovered once the power supply is
restored.

Presentia C v2
https://www.zennio.com/ Technical Support: https://support.zennio.com/
7
2CONFIGURATION
2.1 GENERAL
After importing the corresponding database in ETS and adding the device into the
topology of the desired project, the configuration process begins by entering the
parameters window of the device.
ETS PARAMETERISATION
From General screen it is possible to activate/deactivate all the required functionality.
Figure 2. General
Presence Detection [enabled]
1
: enables the “Presence Detector” tab in the
tree on the left. For more information, see section 2.2.
Logic Functions [enabled/disabled] enables or disables the “Logic
Functions” tab in the tree on the left. For more information, see section 2.3.
Heartbeat (Periodic Alive Notification) [enabled/disabled]: incorporates a
one-bit object to the project (“[Heartbeat] Object to Send ‘1’”) that will be
sent periodically with a value of “1” to notify that the device is still working (still
alive).
Figure 3. Heartbeat
1
The default values of each parameter will be highlighted in blue in this document, as follows:
[default/rest of options].

Presentia C v2
https://www.zennio.com/ Technical Support: https://support.zennio.com/
8
Note: the first sending after download or bus failure takes place with a delay of
up to 255 seconds, to prevent bus overload. The following sendings match the
period set.

Presentia C v2
https://www.zennio.com/ Technical Support: https://support.zennio.com/
9
2.2 PRESENCE DETECTOR
Presentia C v2 incorporates six independent presence detection channels, two more
for constant light control and one for occupancy detection.
Presence detection consists in sending objects to the bus whenever the
device observes a moving body (or no longer observes it) in the environment
of the room where it has been installed.
Constant light control consists in sending KNX orders to the dimmer device
that controls the in-room luminaries so the ambient light level remains
constant even if other light sources are present.
Occupancy detection is an algorithm that allows determining, through a
multiple sensor configuration, whether a particular space is under occupation
no matter if the occupant moves or not (i.e., no matter if the device is
detecting presence in the room or not).
Please refer to the specific manual “Presence Detector” available in Presentia C v2
product section at the Zennio website (www.zennio.com) for detailed information about
the functionality and the configuration of the related parameters.

Presentia C v2
https://www.zennio.com/ Technical Support: https://support.zennio.com/
10
2.3 LOGIC FUNCTIONS
This module makes it possible to perform numeric and binary operations to incoming
values received from the KNX bus, and to send the results through other
communication objects specifically enabled for this purpose.
Presentia C v2 can implement up to 10 different and independent functions, each of
them entirely customisable and consisting of up to 4 consecutive operations.
The execution of each function can depend on a configurable condition, which will be
evaluated every time the function is triggered through specific, parameterisable
communication objects. The result after executing the operations of the function can
also be evaluated according to certain conditions and afterwards sent (or not) to the
KNX bus, which can be done every time the function is executed, periodically or only
when the result differs from the last one.
Please refer to the “Logic Functions” user manual available under the Presentia C v2
product section at the Zennio homepage (www.zennio.com) for detailed information
about the functionality and the configuration of the related parameters.

Presentia C v2
https://www.zennio.com/ Technical Support: https://support.zennio.com/
11
ANNEX I. COMMUNICATION OBJECTS
“Functional range” shows the values that, with independence of any other values permitted by the bus according to the object size, may be of any use or have
a particular meaning because of the specifications or restrictions from both the KNX standard or the application program itself.
Number
Size
I/O
Flags
Data type (DPT)
Functional Range
Name
Function
1
1 Bit
C - - T -
DPT_Trigger
0/1
[Heartbeat] Object to Send '1'
Sending of '1' Periodically
2
1 Byte
I
C - W - -
DPT_SceneNumber
0 - 63
Scene Input
Scene Value
3
1 Byte
C - - T -
DPT_SceneControl
0-63; 128-191
Scene Output
Scene Value
4
2 Bytes
I/O
C R W - -
1.xxx
0/1
Correction Factor - Internal Sensor
[0, 80] x0.1
5
2 Bytes
I/O
C R W - -
1.xxx
0/1
Offset - Internal Sensor
[-200, 200] Luxes
6
2 Bytes
O
C R - T -
DPT_Value_Lux
Luminosity - Internal Sensor
Luxes
10
1 Bit
I
C - W - -
DPT_DayNight
0/1
Day/Night
0 = Day; 1 = Night
1 Bit
I
C - W - -
DPT_DayNight
0/1
Day/Night
0 = Night; 1 = Day
11
1 Bit
I
C - W - -
DPT_Enable
0/1
Detection LEDs
0 = Disable; 1 = Enable
1 Bit
I
C - W - -
DPT_Enable
0/1
Detection LEDs
0 = Disable; 1 = Enable Only During
the Day
12
1 Bit
O
C R - T -
DPT_Switch
0/1
Occupancy: Output (Binary)
Binary Value
1 Bit
C - - T -
DPT_Start
0/1
Occupancy: Slave Output
1 = Motion Detected
13
1 Byte
O
C R - T -
DPT_Scaling
0% - 100%
Occupancy: Output (Scaling)
0-100%
14
1 Byte
O
C R - T -
DPT_HVACMode
1=Comfort
2=Standby
3=Economy
4=Building
Protection
Occupancy: Output (HVAC)
Auto, Comfort, Standby, Economy,
Building Protection
15
1 Bit
I
C - W - -
DPT_Window_Door
0/1
Occupancy: Trigger
Binary Value to Trigger the Occupancy
Detection
16
1 Bit
I
C - W - -
DPT_Start
0/1
Occupancy: Slave Input
1 = Detection from slave device
17
2 Bytes
I
C - W - -
DPT_TimePeriodSec
0 - 65535
Occupancy: Waiting Time
0-65535 s.
18
2 Bytes
I
C - W - -
DPT_TimePeriodSec
0 - 65535
Occupancy: Listening Time
1-65535 s.
19
1 Bit
I
C - W - -
DPT_Enable
0/1
Occupancy: Lock
0 = Unlock; 1 = Lock
1 Bit
I
C - W - -
DPT_Enable
0/1
Occupancy: Lock
0 = Lock; 1 = Unlock
20
1 Bit
O
C R - T -
DPT_Occupancy
0/1
Occupancy: Occupancy State
0 = Not Occupied; 1 = Occupied
21
1 Byte
I
C - W - -
DPT_Scaling
0% - 100%
Sensor 1 Sensitivity
1-100%
22
1 Byte
I
C - W - -
DPT_Scaling
0% - 100%
Sensor 2 Sensitivity
1-100%
23
1 Byte
I
C - W - -
DPT_Scaling
0% - 100%
Sensor 3 Sensitivity
1-100%
24
1 Byte
I
C - W - -
DPT_Scaling
0% - 100%
Sensor 4 Sensitivity
1-100%

Presentia C v2
https://www.zennio.com/ Technical Support: https://support.zennio.com/
12
25, 35, 45, 55, 65, 75
1 Bit
I
C - W - -
DPT_Start
0/1
[Cx] External Motion Detection
1 = Motion detected by an external
sensor
26, 36, 46, 56, 66, 76
1 Bit
O
C R - T -
DPT_Switch
0/1
[Cx] Output (Binary)
Binary Value
27, 37, 47, 57, 67, 77
1 Byte
O
C R - T -
DPT_Scaling
0% - 100%
[Cx] Output (Scaling)
0-100%
28, 38, 48, 58, 68, 78
1 Byte
O
C R - T -
DPT_HVACMode
1=Comfort
2=Standby
3=Economy
4=Building
Protection
[Cx] Output (HVAC)
Auto, Comfort, Standby, Economy,
Building Protection
29, 39, 49, 59, 69, 79
1 Bit
I
C - W - -
DPT_Enable
0/1
[Cx] Lock Status
0 = Unlock; 1 = Lock
1 Bit
I
C - W - -
DPT_Enable
0/1
[Cx] Lock Status
0 = Lock; 1 = Unlock
30, 40, 50, 60, 70, 80
1 Bit
I
C - W - -
DPT_Start
0/1
[Cx] Force State
0 = No Detection; 1 = Detection
31, 41, 51, 61, 71, 81
1 Bit
I
C - W - -
DPT_Start
0/1
[Cx] External Switch
0 = No Detection; 1 = Detection
32, 42, 52, 62, 72, 82
2 Bytes
I/O
C R W - -
DPT_TimePeriodSec
0 - 65535
[Cx] Length of Detection
1-65535 s.
85, 101
1 Bit
I
C - W - -
DPT_Start
0/1
[CLCx] External Motion Detection
1 = Motion detected by an external
sensor
86, 102
1 Bit
I
C - W - -
DPT_Enable
0/1
[CLCx] Lock Status
0 = Unlock; 1 = Lock
1 Bit
I
C - W - -
DPT_Enable
0/1
[CLCx] Lock Status
0 = Lock; 1 = Unlock
87, 103
1 Bit
I
C - W - -
DPT_Start
0/1
[CLCx] Force State
0 = No Detection; 1 = Detection
88, 104
1 Bit
I
C - W - -
DPT_Start
0/1
[CLCx] External Switch
0 = No Detection; 1 = Detection
89, 105
2 Bytes
I
C - W - -
DPT_Value_Lux
[CLCx] Setpoint
Setpoint Value (1-2000)
2 Bytes
I
C - W - -
DPT_Value_Lux
[CLCx] Setpoint During Day
Setpoint Value (1-2000)
1 Byte
I
C - W - -
DPT_Scaling
0% - 100%
[CLCx] Setpoint
Setpoint Value (1-100)%
1 Byte
I
C - W - -
DPT_Scaling
0% - 100%
[CLCx] Setpoint During Day
Setpoint Value (1-100)%
90, 106
2 Bytes
I
C - W - -
DPT_Value_Lux
[CLCx] Setpoint During Night
Setpoint Value (1-2000)
1 Byte
I
C - W - -
DPT_Scaling
0% - 100%
[CLCx] Setpoint During Night
Setpoint Value (1-100)%
91, 107
1 Byte
O
C R - T -
DPT_Scaling
0% - 100%
[CLCx] Dimming Value
Dimming Value (%)
92, 108
2 Bytes
I/O
C R W - -
DPT_TimePeriodSec
0 - 65535
[CLCx] Length of Detection
1-65535 s.
94, 110
1 Bit
I
C - W - -
DPT_Switch
0/1
[CLCx] Manual Control: On/Off (Input)
1-Bit Control
95, 111
4 Bit
I
C - W - -
DPT_Control_Dimming
0x0 (Stop)
0x1 (Dec. by 100%)
...
0x7 (Dec. by 1%)
0x8 (Stop)
0xD (Inc. by 100%)
...
0xF (Inc. by 1%)
[CLCx] Manual Control: Relative
Dimming (Input)
4-Bit Control
96, 112
1 Byte
I
C - W - -
DPT_Scaling
0% - 100%
[CLCx] Manual Control: Absolute
Dimming (Input)
1-Byte Control
97, 113
1 Bit
O
C R - T -
DPT_Switch
0/1
[CLCx] Manual Control: On/Off (Output)
1-Bit Control
98, 114
4 Bit
O
C R - T -
DPT_Control_Dimming
0x0 (Stop)
0x1 (Dec. by 100%)
...
[CLCx] Manual Control: Relative
Dimming (Output)
4-Bit Control

Presentia C v2
https://www.zennio.com/ Technical Support: https://support.zennio.com/
13
0x7 (Dec. by 1%)
0x8 (Stop)
0xD (Inc. by 100%)
...
0xF (Inc. by 1%)
99, 115
1 Bit
I
C - W - -
DPT_Enable
0/1
[CLCx] Manual Control
0 = Disable; 1 = Enable
100, 116
1 Bit
O
C R - T -
DPT_Enable
0/1
[CLCx] Manual Control (Status)
0 = Disabled; 1 = Enabled
117, 118, 119, 120,
121, 122, 123, 124,
125, 126, 127, 128,
129, 130, 131, 132,
133, 134, 135, 136,
137, 138, 139, 140,
141, 142, 143, 144,
145, 146, 147, 148
1 Bit
I
C - W - -
DPT_Bool
0/1
[LF] (1-Bit) Data Entry x
Binary Data Entry (0/1)
149, 150, 151, 152,
153, 154, 155, 156,
157, 158, 159, 160,
161, 162, 163, 164
1 Byte
I
C - W - -
DPT_Value_1_Ucount
0 - 255
[LF] (1-Byte) Data Entry x
1-Byte Data Entry (0-255)
165, 166, 167, 168,
169, 170, 171, 172,
173, 174, 175, 176,
177, 178, 179, 180
2 Bytes
I
C - W - -
DPT_Value_2_Ucount
0 - 65535
[LF] (2-Byte) Data Entry x
2-Byte Data Entry
DPT_Value_2_Count
-32768 - 32767
DPT_Value_Tempo
-273, 00 - 670760, 00
181, 182, 183, 184,
185, 186, 187, 188
4 Bytes
I
C - W - -
DPT_Value_4_Count
-2147483648 - 2147483647
[LF] (4-Byte) Data Entry x
4-Byte Data Entry
189, 190, 191, 192,
193, 194, 195, 196,
197, 198
1 Bit
O
C R - T -
DPT_Bool
0/1
[LF] Function x - Result
(1-Bit) Boolean
1 Byte
O
C R - T -
DPT_Value_1_Ucount
0 - 255
[LF] Function x - Result
(1-Byte) Unsigned
2 Bytes
O
C R - T -
DPT_Value_2_Ucount
0 - 65535
[LF] Function x - Result
(2-Byte) Unsigned
4 Bytes
O
C R - T -
DPT_Value_4_Count
-2147483648 - 2147483647
[LF] Function x - Result
(4-Byte) Signed
1 Byte
O
C R - T -
DPT_Scaling
0% - 100%
[LF] Function x - Result
(1-Byte) Percentage
2 Bytes
O
C R - T -
DPT_Value_2_Count
-32768 - 32767
[LF] Function x - Result
(2-Byte) Signed
2 Bytes
O
C R - T -
9.xxx
-671088.64 - 670433.28
[LF] Function x - Result
(2-Byte) Float

Join and send us your inquiries
about Zennio devices:
http://support.zennio.com
Zennio Avance y Tecnología S.L.
C/ Río Jarama, 132. Nave P-8.11
45007 Toledo (Spain).
Tel. [phone].
www.zennio.com
[email protected]