Zeta PREMIER EX8 User manual

PREMIER EX8 EXTINGUISHING PANEL USER MANUAL
COMBINED FIRE & EXTINGUISHING CONTROL PANEL
COMPLIES WITH BS EN 12094 PART 1 & EN54 PARTS 2 & 4
USER MANUAL
Approved Document No: GLT.MAN-132
Issue : 1.2 Author: NRPJ Date: 06/10/2010

Extinguishing Panel - USER MANUAL
Approved Document No: GLT.MAN-132 PAGE 2
Issue : 1.2 Author: NRPJ Date: 06/10/2010
INDEX
INDEX .......................................................................................................................................2
INTRODUCTION......................................................................................................................3
INDICATIONS & CONTROLS................................................................................................4
Indications..............................................................................................................................4
Controls..................................................................................................................................6
PANEL OPERATION ...............................................................................................................7
Normal Operation...................................................................................................................7
Fire Alarm Condition (Peripheral Zones) ..............................................................................7
What to do in the event of a fire.........................................................................................7
Resetting from an alarm condition.....................................................................................7
First Stage Alarm ...................................................................................................................8
Second Stage Alarm...............................................................................................................8
Hold / Abort a Second Stage Alarm......................................................................................8
Manual Mode .........................................................................................................................8
Reset.......................................................................................................................................9
Faults......................................................................................................................................9
DISABLEMENT......................................................................................................................10
To Programme an Input or Output as Disabled....................................................................10
LOG BOOK .............................................................................................................................11
MAINTENANCE WORK ...................................................................................................11
FALSE ALARMS................................................................................................................12
ALL OTHER EVENTS .......................................................................................................13

Extinguishing Panel - USER MANUAL
Approved Document No: GLT.MAN-132 PAGE 3
Issue : 1.2 Author: NRPJ Date: 06/10/2010
INTRODUCTION
The Premier EX 8 is a combined 2 zone , 1 area extinguishing panel, and 4 zone
conventional fire alarm panel.
It has 2 zones dedicated to the extinguishing section. These are known as crossed or
co-incidence zones. Both circuits will need to be triggered in order to activate the
extinguishing circuit. This kind of operation also referred to as “double – knock”
It has 4 zones for fire detection (referred to as peripheral zones, or fire zones). These
will not trigger the extinguishing circuit.
The Extinguishing section is designed to BSEN12094-1:2003.
The fire alarm section is designed to EN54-2:1998 A1 + A2.
The Power Supply section is designed to EN54-4:1998 A1 + A2
This design allows the same panel to protect an extinguishing area, and also monitor
the rest of the site for a fire.
The panel has an integral Manual Release call point fitted to the front of the panel.
The panel has monitored inputs for field connections, such as manual release,
emergency hold, etc.
The panel has relay outputs for first & second stage alarms, fault & gas fired.
The panel has remote inputs for Start/Stop Sounders, Silence & Reset, to allow the
panel to be controlled remotely.
The panel has Open collector repeat outputs for most panel status indications (eg 1st
stage alarm, 2nd stage alarm, Automatic mode, Manual mode etc)
The panel has a connection for a serial repeater unit (4 wire)
The Premier EX8 can be in any of the following conditions:-
Quiescent condition –ie System Normal
Fire condition –ie a fire on one of the peripheral zones
oThe Premier EX8 will enter the fire condition within 1 second of a
detector on a peripheral zone signalling an alarm.
Fault condition
Disabled condition
Test condition
Pre-activated condition
oThe Premier EX8 will enter the pre-activated condition (first stage
alarm) within 1 second of a detector on one of the crossed zone
signalling an alarm.
Activated condition
oThe Premier EX8 will enter the activated (second stage alarm)
condition within 1 second of the second crossed zone signalling an
alarm.
Released condition
oThe Premier EX8 will enter the released condition (bottle output
activated) within 1 second of establishing the activated condition, OR
after the delay configured in the bottle output timer.
WARNING: Access to live components inside this fire alarm enclosure. The key
to open the door to gain internal access should be held by authorised
personnel only.

Extinguishing Panel - USER MANUAL
Approved Document No: GLT.MAN-132 PAGE 4
Issue : 1.2 Author: NRPJ Date: 06/10/2010
INDICATIONS & CONTROLS
Indications
Here is the fascia for the Premier EX8 panel.
COMBINED FIRE & EXTINGUISHING CONTROL PANEL
COMPLIES WITH BS EN 12094 PART 1:2003 CLASSA& EN54 PARTS 2 & 4
START/STOP
1stSTAGE
SOUNDERS
DISABLED
PANEL EXTINGUISHING SYSTEM
BUZZER by GLT Exports Ltd
MADE IN THE UK
SC
R
OLL
SC
ROLL
SUPPLY
SILENCE FIRE
Each function has its own indication LED. There are Alarm (Active), Fault, Test &
Disablement LEDs for most panel inputs & outputs. Some of these indications are not
applicable for certain functions (EG a fault on the 1st or 2nd stage relays). In such
cases, the LEDs are not present on the matrix (See white outlines above)
For most functions, more than one LED will light (eg zone 1 fire & COMMON
ALARM)
The second stage sounder is pulsed, and it`s sounder active LED will also pulse in
time with the actual sounder output.
The panel also has a 3 digit 7 segment display. This is used to display the countdown
timers during a second stage alarm.

Extinguishing Panel - USER MANUAL
Approved Document No: GLT.MAN-132 PAGE 5
Issue : 1.2 Author: NRPJ Date: 06/10/2010
The Premier EX8 has the following LED indicators:-
LED
COLOUR
FUNCTION / MEANING
POWER
GREEN
The panel is supplied with power, either battery, mains or both
COMMON FIRE
RED
There is an alarm on the system. Check which zone caused the alarm
COMMON FAULT
YELLOW
There is a fault on the system. Another LED(s) will be lit to indicate the specific fault
BATTERY FAULT
YELLOW
There is a problem with the batteries. Rectify or replace.
CHARGER FAULT
YELLOW
The panel is not charging the batteries (usually mains fail or low mains)
LOW BATTERY
YELLOW
The batteries are below their final voltage & should be replaced
EARTH FAULT
YELLOW
Problem in system wiring. At least one cable is shorting to earth.
EXT.FAN DISABLE
YELLOW
The external equipment relay has been disabled
SYSTEM FAULT
YELLOW
The CPU has crashed, (Or CPU reset has been pressed & held)
REMOTE FAULT
YELLOW
The panel has received a fault input from external equipment
REPEATER FAULT
YELLOW
The panel has lost communication with the repeater panel
GEN S/C FAULT
YELLOW
Indicated that a line fault is caused by a short circuit
EXTINGUISHANTRELEASED
RED
The bottle output has been activated & the gas released
RELEASEIMMINENT
RED
The panel has started the release timer and will activate bottle imminently
HOLD/ABORT
YELLOW
An emergency hold OR emergency abort input has been activated.
MANUALRELEASE
RED
A manual release call point has been activated
1ST STAGEALARM
RED
One of the crossed zones is in alarm
2ND STAGEALARM
RED
Both of the crossed zones are in alarm
LOWPRESSURE
YELLOW
A drop in bottle pressure has been detected
FLOODINGZONEFAULT
YELLOW
There is a fault relating to the flooding zone1 (ie the extinguishing section of the panel)
MANUALMODE
YELLOW
The panel is in manual only mode (ie will not be triggered by detectors)
AUTOMATICMODE
GREEN
The panel is in automatic or manual mode
GENERALDISABLEMENT
YELLOW
Lights when any section of the system is disabled
GENERALTEST
YELLOW
Lights when any section of the panel is in test mode
CONTROLSACTIVE
YELLOW
Lights when controls enabled keyswitch is on
ZONE1-6FIRE
RED
Lights when one of the detection zones is in alarm
ZONE1-6FAULT
YELLOW
Lights when one of the detection zones has a fault
ZONE1-6TEST
YELLOW
Lights when one of the detection zones is in test mode
ZONE1-6DISABLED
YELLOW
Lights when one of the detection zones is in disablement mode
1ST STAGESNDRACTIVE
RED
Lights when the first stage sounder is on
1ST STAGESNDRFAULT
YELLOW
Lights when the first stage sounder has a wiring fault
1ST STAGESNDRTEST
YELLOW
Lights when the first stage sounder is in test mode
1ST STAGESNDRDISABLED
YELLOW
Lights when the first stage sounder is disabled
2ND STAGESNDRACTIVE
RED
Lights when the second stage sounder is on
2ND STAGESNDRFAULT
YELLOW
Lights when the second stage sounder has a wiring fault
2ND STAGESNDRTEST
YELLOW
Lights when the second stage sounder is in test mode
2ND STAGESNDRDISABLED
YELLOW
Lights when the second stage sounder is disabled
BOTTLEOUTPUTACTIVE
RED
Lights when the bottle output is on
BOTTLEOUTPUTFAULT
YELLOW
Lights when the bottle output has a wiring fault
BOTTLEOUTPUTDISABLED
YELLOW
Lights when the bottle output is disabled
1ST STAGERELAYACTIVE
RED
Lights when the first stage relay is on
1ST STAGERELAYTEST
YELLOW
Lights when the first stage relay is in test mode
1ST STAGERELAYDISABLED
YELLOW
Lights when the first stage relay is disabled
2ND STAGERELAYACTIVE
RED
Lights when the second stage relay is on
2ND STAGERELAYTEST
YELLOW
Lights when the second stage relay is in test mode
2ND STAGERELAYDISABLED
YELLOW
Lights when the second stage relay is disabled
MAN.LRELEASEINPUTACTIVE
RED
A manual release call point connected to the remote input has been activated
MAN.RELEASEINPUTFAULT
YELLOW
Fault in wiring to Manual release call point
MAN.RELEASEINPUTDISABLED
YELLOW
Manual release call point circuit is disabled
GASFIREDINPUTACTIVE
RED
The panel has received a signal from the cylinder to say the gas has been released.
GASFIREDINPUTFAULT
YELLOW
There is a wiring fault to the bottle`s sensor
EMERG.HOLDINPUTACTIVE
YELLOW
The emergency hold input has been activated
EMERG.HOLDINPUTFAULT
YELLOW
Fault in wiring to Emergency hold switch
EMERG.ABORTINPUTACTIVE
YELLOW
The emergency abort input has been activated
EMERG.ABORTINPUTFAULT
YELLOW
Fault in wiring to Emergency abort switch
AUTO/MANUALINPUTACTIVE
YELLOW
The panel has been set to manual mode by a remote input
AUTO/MANUALINPUTFAULT
YELLOW
Fault in wiring to Auto / Manual switch
PRESS.SWITCHINPUTACTIVE
YELLOW
The bottle`s pressure switch output has been activated
PRESS.SWITCHINPUTFAULT
YELLOW
Fault in wiring to bottle`s pressure switch
BOTTLESCALESINPUTACTIVE
YELLOW
The bottle`s scales switch has been activated
BOTTLESCALESINPUTFAULT
YELLOW
Fault in wiring to bottle`s scales switch
ACCESSLEVEL3
YELLOW
Access level 3 selected
GASRELEASECOUNTER
YELLOW
Gas release counter is being displayed on 3 digit display
RELEASEDURATIONTIME
YELLOW
Release duration time is being displayed on 3 digit display
RESETINHIBITTIME
YELLOW
Reset inhibit time is being displayed on 3 digit display

Extinguishing Panel - USER MANUAL
Approved Document No: GLT.MAN-132 PAGE 6
Issue : 1.2 Author: NRPJ Date: 06/10/2010
Controls
The Premier EX8 has the following controls:-
LABEL
USE
START/STOP 1st
STAGE SOUNDER
Used to silence the sounders in an alarm, or to manually start the FIRST
STAGE sounders to evacuate building
SILENCE BUZZER
Used to silence the panel`s internal buzzer in a fault or alarm condition.
RESET FIRE
PANEL
Used to reset the Fire detection section of the Control panel (Ie Zones 1 to 6)
RESET
EXTINGUISHING
SYSTEM
Used to Reset the extinguishing section of the Control panel.
LED TEST
To check that all indicator LEDs are working. Use as part of the daily / weekly
fire alarm inspection.
DISABLE
Used to access Disablement mode
DISABLE –
SELECT
Used to scroll to select which part of the system to disable
DISABLE –
CONFIRM
Used to confirm disablement of the highlighted part of the system.
TEST
Used to access test mode
TEST –SELECT
Used to scroll to select which part of the system to test
TEST –CONFIRM
Used to confirm test mode of the highlighted part of the system.
AUTO / MANUAL
Used to toggle between automatic & manual only mode
GAS RELEASE
COUNTER
Used to view or alter Gas Release Counter
RELEASE
DURATION TIME
Used to view or alter Release Duration Time Counter
RESET INHIBIT
TIME
Used to view or alter Reset Inhibit Time Counter
0-9
To enter access code & timer values
ENTER
To confirm new timer setting
CANCEL
To Save an edited time and exit from the timer set-up.
TERMINATE
DURATION TIMER
Used to terminate the release duration timer (Bottle output Active). Internal
button. Used during commissioning only.
Note that the controls can only be used after the keyswitch has been turned to the
CONTROLS ENABLED (ON) position.
As the Premier EX8 is a combined Extinguishing & fire alarm control panel, it is
possible that both the extinguishing section, and the fire alarm section are in alarm at
the same time. If this occurs, the reset Fire Panel button can be used to reset the
Zone alarms, leaving the extinguishing section active. After the pre-programmed
Reset Inhibit delay, the reset Extinguishing System button can then be used to reset
the extinguishing section.
If the Extinguishing system has been through it`s release cycle, and the zones that
triggered the release are still in alarm, the reset fire panel button must be pressed
first to reset the zones in alarm, before the reset extinguishing system button can be
pressed.

Extinguishing Panel - USER MANUAL
Approved Document No: GLT.MAN-132 PAGE 7
Issue : 1.2 Author: NRPJ Date: 06/10/2010
PANEL OPERATION
Normal Operation
With the “CONTROL” Key in the “OFF” position and under normal conditions the
system will be silent and the green “POWER LED” illuminated.
The system may either be in “Automatic” or “Manual” mode of operation. This will be
evident by the illumination of either the “Automatic” or “Manual” LED. In Manual
Mode, the bottle output will not be activated automatically. It must be started
manually by pressing a manual release call point.
Fire Alarm Condition (Peripheral Zones)
The Premier EX8 signals an alarm by the following:-
Turn on the General Fire LED
Turn on the Zonal Fire Indicator
Turn on internal buzzer
Start any sounders connected to the panel`s sounder circuits
Activate the fire relay
What to do in the event of a fire.
1. Follow the building evacuation procedure, and check that everyone has left
the building safely.
2. The building fire officer or suitably trained responsible person should
CAREFULLY enter the building, and locate the area of the alarm from the fire
alarm panel.
3. Investigate to determine the cause of the alarm. Look for the detector in the
zone in alarm that signalled the fire. The detector that signalled an alarm will
have its RED ALARM LED on.
4. If a small fire is found, a suitably trained person could tackle this with a
suitable fire extinguisher.
5. If a larger fire is found, leave the building immediately, and contact the fire
brigade.
6. If no fire is found, make a note of the detector that signalled fire, and look for
anything nearby that could be the cause of the activation, eg cooking, or use
of a hot air gun etc.
7. Record findings in the fire alarm log book.
Resetting from an alarm condition
After the relevant action has been taken, the Premier EX8 fire alarm panel can be reset by the
following:-
1 Press Start/Stop sounder button, This will silence the external sounders.
2 Press Silence Fault Tone button. This will silence the panel`s internal buzzer.
3 Press the Reset button. This will return the panel to it`s normal condition.
If the panel goes straight back into alarm, then the cause of the alarm has not been cleared. This
could be a detector still exposed to smoke, or a call point still in the active position. Press
Start/Stop Sounder button, followed by silence buzzer button on the panel, then investigate for a
call point, or detector that still has it`s RED ALARM LED on. Reset the call point, or clear the
smoke. If the problem persists, contact an engineer.

Extinguishing Panel - USER MANUAL
Approved Document No: GLT.MAN-132 PAGE 8
Issue : 1.2 Author: NRPJ Date: 06/10/2010
First Stage Alarm
On detection of a “FIRE” in either Zone 1 or Zone 2, the zone fire LED will be
illuminated and the internal buzzer will be on. The first stage LED and first stage
sounder will be on. The first stage relay output will be active.
To silence the sounder, turn the keyswitch to ON position, and press silence button.
The panel’s internal tone and fire LEDs will remain active until the cause of the alarm
has been removed, and the panel has been reset
A first stage alarm can be created manually by turning the keyswitch to the on
position and pressing the 1st STAGE ALARM button.
A first stage alarm can be silenced & reset when the panel is in automatic or manual
mode.
Second Stage Alarm
As soon as a “FIRE” is detected in the second Zone, the second stage alarm is
initiated. The second stage sounder will be pulsed on for 1 second, then off for 1
second. This will be repeated as the timer counts down. The two-zone alarm LEDs
will be illuminated as well as first stage alarm, second stage alarm and Gas Imminent
LEDs. The second stage cannot be silenced and after a delay period, (Set by the the
installer) the extinguishing output will be initiated releasing the extinguishing agent,
and the second stage sounder will now be on constantly. This will be followed by the
“GAS FIRED” indication, indicating that the extinguishing agent has been released.
Once the second stage alarm has been initiated, it is advisable to evacuate and Seal
the protected area prior to the release of the extinguishing agent.
Also, the operation of the Yellow “Manual Release” call point will initiate the second
stage alarm. To do this, lift the flap and push the operating element.
A second stage alarm can only be silenced & reset when the panel is in manual
mode.
Hold / Abort a Second Stage Alarm
If the hold input is activated during a second stage alarm, the second stage sounder
will now pulse on for 0.5 seconds, then be off for 2 seconds, and will repeat. The
counter will be reset to it`s programmed value and the panel will restart it`s
programmed countdown when the input is released. If an abort input is used, the
panel will abort the gas release, and the panel will need to be reset.
Manual Mode
In this mode operation, Zone Fire and Fault alarms are still in operation, and first &
second stage sounders will operate, but the bottle output to the extinguishing agent
will not operate.

Extinguishing Panel - USER MANUAL
Approved Document No: GLT.MAN-132 PAGE 9
Issue : 1.2 Author: NRPJ Date: 06/10/2010
Reset
To reset panel from an alarm condition, press Start/Stop Sounders, Silence Buzzer,
then Reset. If the panel enters the second stage alarm (while in automatic mode), the
panel cannot be reset until the reset inhibit timer has finished it`s countdown.
The panel can NOT be reset from a fault condition. All faults are non latching, so
when a fault clears from the panel it will be automatically cleared from the display.
Faults
The relevant LED will illuminate and the internal tone will sound. Pressing the
“Silence buzzer” button, with the control key “ON”, will silence the tone. If there are
any faults, call an Engineer.

Extinguishing Panel - USER MANUAL
Approved Document No: GLT.MAN-132 PAGE 10
Issue : 1.2 Author: NRPJ Date: 06/10/2010
DISABLEMENT
The Premier EX8 allows any of the following to be disabled to aid commissioning and assist routine
maintenance work:-
Crossed zones
Peripheral Zones
First stage sounders
Second stage sounders & Bottle output (Disabled together)
First Stage Relay
Second Stage Relay
External Equipment Relay
When an zone is disabled, the panel will not respond to any fault or fire signals it receives from that
input. When an output is disabled, the panel will not activate that output.
This might be used if the system requires routine maintenance, and the customer needs the system to
continue running, but doesn’t want spurious false alarms or fault signals.
The panel will respond in the usual manner to any events in any non-disabled inputs.
To Programme an Input or Output as Disabled
Any number of inputs or outputs can be disabled, but it is good practice to only disable the minimum
requirement at a time.
Insert and turn control key to enabled position;
Press DISABLE button and the GENERAL DISABLEMENT LED will come on (flashing fast, 4 flashes
then off, repeated);
Press SELECT button. The GENERAL DISABLEMENT LED will light steady, and the Crossed Zone 1
Disabled LED will flash 4 quick flashes & off. The panel is now in SELECT DISABLEMENT MODE.
The select button is used to highlight (flash) the section that needs to be disabled. Press select button
until the correct LED is flashing, then press confirm. The LED will now flash 4 quick flashes & on, to
indicate that this section is disabled.
If more than one section needs to be disabled, then press SELECT button again until the required
zone is selected. (The previously disabled section will now have its disabled LED lit steady.)
If the panel needs to be taken out of SELECT DISABLEMENT MODE (eg to silence a fault on another
part of the system), turn the keyswitch off, then back on again.
Once all the work has been done the zones need to be enabled again. If the panel is not in SELECT
DISABLEMENT MODE, turn the keyswitch to controls enabled, press DISABLE button.
Press the scroll button until the disabled section has been selected. Press CONFIRM button to re-
enable. Scroll to any other disabled section and enable in the same way. When all sections are
enabled again, turn the keyswitch to off to return the system to normal.
NOTE: During a Disabled condition, sections of the fire alarm system will be
inoperative. Extra caution should be used in the disabled part of the premises.

Extinguishing Panel - USER MANUAL
Approved Document No: GLT.MAN-132 PAGE 11
Issue : 1.2 Author: NRPJ Date: 06/10/2010
LOG BOOK
MAINTENANCE WORK
DATE
TIME
ZONE / LOCATION
REASON FOR WORK
WORK CARRIED OUT
ADDITIONAL WORK REQUIRED
SIGNED

Extinguishing Panel - USER MANUAL
Approved Document No: GLT.MAN-132 PAGE 12
Issue : 1.2 Author: NRPJ Date: 06/10/2010
FALSE ALARMS
DATE
TIME
ZONE /
LOCATION
CAUSE (IF KNOWN)
OR ACTIVITIES IN
ALARM AREA
MAINTENANCE
VISIT NEEDED
(YES/NO)
MAINTENANCE
FINDINGS
CATEGORY OF
FALSE ALARM
FURTHER
ACTION
REQUIRED
SIGNED

Extinguishing Panel - USER MANUAL
Approved Document No: GLT.MAN-132 PAGE 13
Issue : 1.2 Author: NRPJ Date: 06/10/2010
ALL OTHER EVENTS
DATE
TIME
ZONE / LOCATION
DETAILS OF EVENT
(INCLUDING CAUSE IF KNOWN)
ACTION
REQUIRED
DATE
COMPLETED
INITIALS