Zeta ZIOU User manual

DOC: GLT.MAN-126
ISSUE: 1
www.gltexports.com DATE: 14/4/08
ALARM SYSTEM
S
ADDRESSABLE INTERFACE UNITS
ZIOU – ADDRESSABLE INPUT OUTPUT UNIT
5
0
4
9
6
1
3
8
7
2
5
0
4
9
6
1
3 8
7
2
5
0
4
9
6
1
3 8
7
2
D
Connections & Address Setting
The ZIOU has the following connections:-
Loop IN +
Loop IN – (2 connections)
Loop OUT +
Loop out –
MON I/P (2 connections)
AUX RELAY (3 connections, NO, CM, NC)
Normally the loop cables will be connected one pair of +/- to the IN terminals (use either IN-
terminal), and the other pair of cables to the OUT terminals. If the isolator needs to be
PERMANENTLY bypassed, connect the – OUT to the spare –IN terminal. To temporarily bypass
the isolator (eg for a DVM cable continuity check), fit a shorting link to position J1.
The ZIOU is now addressed by 3 rotary switches, one for 100`s one for 10`s, one for units. Select
an address between 1 & 126. (The picture shows 037)
PCB Identification
The same PCB is used for The
ZIU (input only), ZIOU (Input
with volt free relay output), and
ZSCC (sounder circuit
controller). Each PCB will have
an Identification mark (tick or
“X”) to show which model it is.
Description
The Zeta addressable Input Output Unit (ZIOU) is used to
interface external equipment to any Zeta Analogue
Addressable fire alarm system. It has a switch monitoring
input with a 47k end of line resistor, and a Volt Free SELV
relay output.
The unit has a built in loop short circuit isolator to help
keep the unit operational in the event of a problem on the
addressable loop wiring.
It has 3 indication LEDs on the front of the unit. One for
Ala
r
m
,
one for local fault and one for addressable loo
p
fault
(
Isolator active
)
.

DOC: GLT.MAN-126
ISSUE: 1
www.gltexports.com DATE: 14/4/08
ALARM SYSTEM
S
ADDRESSABLE INTERFACE UNITS
ZIOU – ADDRESSABLE INPUT OUTPUT UNIT
Technical Data
OPERATING VOLTAGE 17 – 33V DC
QUIESCENT CURRENT 900uA
ALARM CURRENT 10.6mA
FAULT CURRENT 2.8mA
ISOLATING CURRENT 7.3mA
INPUT END OF LINE 47K
DEVICE NORMAL RESISTANCE (RETURN VALUE 16) 10K to 75K
DEVICE OPEN CCT FAULT RESISTANCE (RETURN VALUE 4) 85K to open circuit
DEVICE ALARM RESISTANCE (RETURN VALUE 64) 0K to 5K
RELAY RATING 1 AMP SELV ONLY
OPERATING TEMPERATURE 0oC to 50oC
MAX HUMIDITY 95% RH Non Condensing
IP RATING IP43
SIZE 127 x 88 x 59 mm
WEIGHT 220
g
Short Circuit Isolator Specification
MAXIMUM LINE VOLTAGE 33V DC
MINIMUM LINE VOLTAGE (NON ISOLATING) 17V DC
MAXIMUM RATED CONTINUOUS CURRENT 1 Amp
MAXIMUM RATED SWITCHING CURRENT 3 Amp
MAXIMUM LEAKAGE CURRENT (ISOLATING) 0.7 mA
MAXIMUM SERIES IMPEDENCE 0.2 Ohm
ISOLATION VOLTAGE 15.6V +/- 0.5V
ISOLATION RESPONSE TIME 25 us to 300 us
RECONNECTION VOLTAGE 18.5V +/- 0.5V
RECONNECTION TIME UP TO 2 SEC
Troubleshooting
DEVICE NOT SEEN BY PANEL CHECK ADDRESS SETTING
CHECK WIRING TO DEVICE (FOR CONTINUITY & POLARITY)
CHECK FOR LOOP VOLTAGE AT DEVICE + & - TERMINALS
DEVICE REPORTS A FAULT (ANALOGUE VALUE 4) CHECK WIRING FROM DEVICE TO MONITORED CONTACT
CHECK FOR CORRECT END OF LINE
DEVICE REPORTS AN ALARM (ANALOGUE VALUE 64) CHECK IF MONITORED CONTACTS ARE OPERATING CORECTLY
CHECK FOR SHORT CIRCUIT ON WIRING
CHECK THAT A NORMALLY CLOSED CONTACT IS NOT USED
ANALOGUE VALUE UNSTABLE CHECK FOR DOUBLE ADDRESS FAULTS
CHECK FOR LOOP DATA CORRUPTION WITH LOOP TEST TOOL
LOOP FAULT (ISOLATING) LED ON CHECK FOR SHORT CIRCUIT ON LOOP
CHECK FOR WRONG POLARITY CONNECTION TO LOOP DEVICES
CHECK FOR TOO MANY DEVICES BETWEEN ISOLATORS
RELAY NOT OPERATING IN ALARM PREMIER AL: - CHECK RELAY HAS BEEN PROGRAMMED
CORRECTLY
PREMIER AD:- RELAY MAY BE CONFIGURED AS ZONAL IF
DETECTORS ARE ADDRESSED IN THE SAME ZONE
CHECK RELAY RATING HAS NOT BEEN EXCEEDED
DISCONNECT LOAD & CHECK THAT RELAY SWITCHES
Protocol usage
The ZIOU addressable interface unit`s relay is controlled by command bit 0 from the control panel. It`s operation will depend on whether the
control panel has pre-configured outputs (EG Simplicity), or programmable outputs (EG Premier AL)
All it`s indication LEDs are under its own control.
In the event of an alarm
,
it will set in
p
ut bit 0 to an active condition
,
as well as settin
g
it’s analo
g
ue value to 64 to indicate it’s activation.
Other information
Like all electronic equipment, at the end of it`s working life this unit should not be disposed of in a refuse bin.
It should be taken to a local reprocessing site as per the guidelines of the WEEE directive, for correct disposal.
Input/Output section designed to EN54-18:2005
Short Circuit Isolator section designed to EN54-17:2005