Ziegler & Brown ZG3GCARTC User manual

ZIEGLER & BROWN
TRIPLE GRILL
MOBILE CART
ASSEMBLY INSTRUCTIONS
CART CODE: ZG3GCARTC
SUITS ZIGGY TRIPLE GRILL

ASSEMBLY INSTRUCTIONS
PARTS LIST
FIRST CHECK THAT YOU HAVE ALL THE PARTS:
ITEM PART NAME QTY PICTURE SPARE PART CODE
ALEFT FRONT LEG 1 ZG3G010304AC
BLEFT BACK LEG 1 ZG3G010303AC
C
RIGHT FRONT LEG
(WITH AXLE HOLE) 1 ZG3G010304BC
D
RIGHT BACK LEG
(WITH AXLE HOLE) 1 ZG3G010303BC
E BOTTOM MESH 1 ZG3G010306
FCART TABLE +
PIN ASSEMBLY 1 ZG3G030101
G HUBCAP 2 ZGTG001A0310C
H WHEEL 2 ZGTG0302F
IAXLE 1 ZG3G010307
J CONDIMENT TRAY 1 ZG3G010305
K CYLINDER HOOK 1 ZGTG0314
XLEG SUPPORT FRONT
LEFT & REAR RIGHT 2 ZG3G010309
YLEG SUPPORT FRONT
RIGHT & REAR LEFT 2 ZG3G010310
Z CASTOR WITH LOCK 2 ZG3G010308
1JJ FRONT PANEL
BLACK
BLACK
BLACK
BLACK
ZG3G0203401

ASSEMBLY INSTRUCTIONS
FASTENERS
MARK ITEM DESCRIPTION PICTUREQTY.
L
M
N
O
P
Q
R
S
T
M6 x 20mm Bolt
Allen Key Head
M6 x 50mm Bolt
Allen Key Head
M6 Nut
Spacer
Split Pin
M6 Allen Key
Spanner
Spanner
Allen Keyhead
Self Tapping Screws
17
4
9
2
1
1
1
1
5
(COMPLETE BOLT PACK SPARE PART CODE ZG3GCARTBP)

ASSEMBLY INSTRUCTIONS
Turn the TABLE (F) LEGS
(A), (B), (C), (D) as shown so that the legs all lean outwards. Matching the colour
RIGHT SIDE LEGS (C) AND (D)
holes need to be both on the same side as shown. Secure each leg with one
M6 X 50mm BOLT (M) and one M6 NUT (N). Don’t fully tighten yet.
Step 1
LEFT BACK LEG (B)
RIGHT BACK LEG (D)
(WITH AXLE HOLE)
LEFT FRONT LEG (A)
RIGHT FRONT LEG (C)
(WITH AXLE HOLE)
FRONT
M6 X 50mm BOLT (M) 4 PCS SPANNER (R) 1 PC
ALLEN KEY (Q) 1 PC
M6 NUT(N) 4 PCS
TABLE (F)
coded stickers makes this easier. The with axle

Step 2
LEG SUPPORT (X)
LEG SUPPORT (Y)
CYLINDER HOOK (K)
M6 NUT(N) 5 PCS
M6 X 20mm BOLT ALLEN KEY HEAD(L) 9 PCS
Fit the four LEG SUPPORTS (X & Y) as shown to brace the legs to the table us-
ing eight M6 x 20mm Bolts (L) and four M6 Nuts (N). Matching the colour coded
using one M6 x 20mm Bolt (L) and one M6 Nut (N).
stickers makes this easier. Use the Allen Key and the Spanner (R) together to
help hold the nut while you turn the bolt. Bolt the cylinder hook in place as shown

Fit the BOTTOM MESH (E) using four M6 X 20mm BOLTS (L).
Once all four bolts are in place, fully tighten using the M6 Allen Key (Q).
Step 3
M6 X 20mm BOLT ALLEN KEY HEAD(L) 4 PCS
BOTTOM MESH (E)

Figure 1
Figure 2
Pre-installed
JJ
Step 4 First unscrew all the six pre-installed bolts from the CART FRONT LEGS (Figure 1).
Then install the FRONT PANEL (JJ) onto the CART FRONT LEGS with the same
six bolts (Figure 2).
The brand name needs to be facing out as shown. Now go back and fully tighten all
nuts and bolts used in Steps 1, 2, 3 & 4.

Thread the AXLE (I) FIRST WHEEL (H), then through a SPACER
(O), then through the legs, then through another SPACER (O), then through
another WHEEL (H).
SPLIT PIN (P) into the axle, and clip the HUBCAPS (G) to the wheels.
one CASTOR WITH LOCK (Z) onto each leg and tighten
SPANNER (S).
Step 5
SPACER (O) 2PCS
SPLIT PIN (P) 1PCS
SPANNER (S) 1PCS

Turn the cart the correct way up and lock each leg in place with one M6 X 20mm
BOLT (L) ALLEN KEY (Q). Do not overtighten.
Step 6
M6 X 20mm BOLT ALLEN KEY HEAD(L) 4PCS
ALLEN KEY (Q) 1 PC

Hook the CONDIMENT TRAY (J) SELF
TAPPING SCREWS (T).
Step 7
SELF TAPPING SCREWS (T) 5PCS
(INSIDE VIEW)
CONDIMENT TRAY (J)