Ziegler & Brown ZG3GCARTK Installation guide

ZIEGLER & BROWN
TRIPLE GRILL
MOBILE CART
ASSEMBLY INSTRUCTIONS
CART CODE: ZG3GCARTK
Tool Required:
1 x Phillips Head Screwdriver

ASSEMBLY INSTRUCTIONS
PARTS LIST
FIRST CHECK THAT YOU HAVE ALL THE PARTS:
ITEM PART NAME QTY PICTURE SPARE PART CODE
A LEFT FRONT LEG 1 ZGTG0304A
B LEFT BACK LEG 1 ZGTG0303A
CRIGHT FRONT LEG
(WITH AXLE HOLE) 1 ZGTG0304B
DRIGHT BACK LEG
(WITH AXLE HOLE) 1 ZGTG0303B
E BOTTOM MESH 1 ZGTG0306
F TABLE 1 ZGTG030101
G HUBCAP 2 ZGTG001A0310
H WHEEL 2 ZGTG0302F
IAXLE 1 ZGTG0309
J CONDIMENT TRAY 1 ZGTG0305
K CYLINDER HOOK 1 ZGTG0314
XLEG SUPPORT FRONT
LEFT & REAR RIGHT 2
YLEG SUPPORT FRONT
RIGHT & REAR LEFT 2
Z WHEEL WITH LOCK 2

ASSEMBLY INSTRUCTIONS
FASTENERS
MARK ITEM DESCRIPTION PICTUREQTY.
L
M
N
O
P
Q
R
S
T
M6 x 20mm Bolt
Allen Key Head
M6 x 50mm Bolt
Allen Key Head
M6 Nut
Spacer
Split Pin
M6 Allen Key
Spanner
Spanner
Self Tapping Screws
17
4
13
2
1
1
1
1
5

ASSEMBLY INSTRUCTIONS
Turn the TABLE (F) upside down onto a stable at surface. Insert the four LEGS
(A), (B), (C), (D) as shown so that the legs all lean outwards. The RIGHT SIDE
LEGS (C) AND (D) with axle holes need to be both on the same side as shown.
Secure each leg with one M6 X 50mm BOLT (M) and one M6 NUT (N). Don’t fully
tighten yet.
Step 1
LEFT BACK LEG (B)
RIGHT BACK LEG (D)
(WITH AXLE HOLE)
LEFT FRONT LEG (A)
RIGHT FRONT LEG (C)
(WITH AXLE HOLE)
FRONT
M6 X 50mm BOLT (M) 4 PCS SPANNER (R) 1 PC
ALLEN KEY (Q) 1 PC
M6 NUT(N) 4 PCS
TABLE (F)

Step 2
LEG SUPPORT (X)
LEG SUPPORT (Y)
CYLINDER HOOK (K)
M6 NUT(N) 5 PCS
M6 X 20mm BOLT ALLEN KEY HEAD(L) 9 PCS
Fit the four LEG SUPPORTS (X & Y) as shown to brace the legs to the table us-
ing eight M6 x 20mm Bolts (L) and four M6 Nuts (N).
Bolt the cylinder hook in place as shown using one M6 x 20mm Bolt (L) and one
M6 Nut (N).

Fit the BOTTOM MESH (E) using four M6 X 20mm BOLTS (L).
Once all bolts are in place, fully tighten using a Phillips Head Screwdriver.
Now tighten the bolts and nuts from the previous steps as well
Step 3
M6 X 20mm BOLT ALLEN KEY HEAD(L) 4 PCS
BOTTOM MESH (E)

Thread the AXLE (I) FIRST rst through a WHEEL (H), then through a SPACER
(O), then through the legs, then through another SPACER (O), then through
another WHEEL (H).
Now t the SPLIT PIN (P) into the axle, and clip the HUBCAPS (G) to the wheels.
On the other two leg, t WHEEL WITH LOCK (Z) on this leg and tighten rmly
using SPANNER (S).
Step 4
AXLE (I)
HUBCAP (G)
SPLIT PIN (P)
WHEEL (H)
SPACER (O)
SPACER (O) 2PCS
SPLIT PIN (P) 1PCS
WHEEL WITH LOCK (Z)
SPANNER (S)
SPANNER (S) 1PCS

Turn the cart correct way up and lock each leg in place with one M6 X 20mm
BOLT (L) as shown. Tighten rmly using the ALLEN KEY (Q). Do not overtighten,
the assembly will be very strong if these bolts are rm
Step 5
M6 X 20mm BOLT ALLEN KEY HEAD(L) 4PCS
ALLEN KEY (Q) 1 PC

Hook the CONDIMENT TRAY (J) into place and secure rmly with ve SELF
TAPPING SCREWS (T).
Step 6
CONDIMENT TRAY (J)
FRONT
(INSIDE VIEW)
SELF TAPPING SCREWS (T) 3PCS

Set all four leg locking pins to their “open” position by gently pulling outwards and
twisting the rings to their “open” horizontal position as shown below.
Place your Ziegler and Brown Triple Grill (SOLD SEPARATELY) in place on the
table with the control panel at the front, cart wheels on the right as shown below.
Set all four leg locking pins to their “locked” position by turning the ring to vertical
as shown below.
Make sure the pins engage into the barbeque legs.
Step 7
LEG LOCKING PINS “OPEN”
LEG LOCKING PINS “LOCKED”

Step 8 Refer to your Ziegler and Brown Triple Grill instruction manual for details on
attaching and safety connecting the gas supply.

More Information?
Need more information or assistance in any way?
You can call your Barbeque Galore store where barbeque experts will be happy
to help you.
Just phone [phone] for your nearest store.
Or visit our website at: www.barbequesgalore.com.au
OPTIONAL ACCESSORIES STORAGE INSTRUCTIONS
First Second
Third
Fourth
Complete