ZIGBEE ROB 200-035-0 User manual

16A ZigBee In-wall Switch 09.ZG09SAPB.04736
Function introduction
Important: Read All Instructions Prior to Installation
“Reset” Key: for
network pairing,
touchlink, factory
reset of the switch
• ZigBee in-wall switch based on latest ZigBee 3.0 protocol
• 100-240VAC wide input and output voltage
• Supports resistive loads and capacitive loads
• 1 channel output, max. load 16A
• Input and output with screw terminals, safe and reliable
• Enables to control ON/OFF of connected load
• ZigBee end device that supports Touchlink commissioning
• Can directly pair to a compatible ZigBee remote via Touchlink without coordinator
• Supports self-forming zigbee network without coordinator and add other devices to the network
• Supports find and bind mode to bind a ZigBee remote
• Supports zigbee green power and can bind max. 20 zigbee green power switches
• Compatible with universal ZigBee gateway products
• Can be controlled by toggle on/off switches
• Active power and energy metering functionality
• Mini size, easy to be installed into a standard size wall box
• Radio frequency : 2.4GHz
• Waterproof grade: IP20
Input Voltage Output Voltage Output Current
Product Data
Size(LxWxH)
100-240VAC 16A max 100-240VAC 45.5x45x20.3mm
• DO NOT install with power applied to device.
• DO NOT expose the device to moisture.
Safety & Warnings
Operation
1.Do wiring according to connection diagram correctly.
Step 1: Remove the device from previous zigbee network if it has already been added to, otherwise pairing will
fail. Please refer to the part "Factory Reset Manually".
Step 2: From your ZigBee Controller or hub interface, choose to add lighting device and enter Pairing mode as
instructed by the controller.
Step 4: Connected light will blink 5
times and then stay solid on, then the
device will appear in your controller's
menu and can be controlled through
controller or hub interface.
2.This ZigBee device is a wireless receiver that communicates with a variety of ZigBee compatible systems. This
receiver receives and is controlled by wireless radio signals from the compatible ZigBee system.
ZigBee Clusters the device supports are as follows:
Input Clusters
• 0x0000: Basic • 0x0003: Identify • 0x0004: Groups • 0x0005: Scenes • 0x0006: On/off
• 0x0702: Simple Metering • 0x0b04: Electrical Measurement • 0x0b05: Diagnostics
Output Clusters
• 0x0019: OTA
• When load current is over 16.1A for over 10 seconds, the relay will be forced to off and protected.
• When load power is over 3700W for over 5 seconds, the relay will be forced to off and protected.
Over Current Protection
LED indicator: stays off if the device
is not added to a Zigbee network,
stays solid on after the device is
added to a network. Same indication
as connected load when commissioning
the device: network pairing, touchlink,
factory reset
AC 100-240V power input
1 CH load output
Switch input
NC
S
Zigbee In-Wall Switch
Compatible Load Types
Load Symbol Load Type Maximum Load Remarks
Due to variety of LED lamp
designs, maximum number
of LED lamps is further
dependent on power factor
result when connected to
switch.
Maximum permitted number
of drivers is 1220W divided
by driver nameplate power
rating.
LED lamps with transformers
LED drivers
Incandescent lighting,
HV Halogen lamps
Low voltage halogen
lighting with electronic
transformers
1220W @ 230V
580W @ 110V
3680W @ 230V
1760W @ 110V
1220W @ 230V
580W @ 110V
580W @ 110V
1220W @ 230V
Electrical appliances
such as television,
refrigerator, water
heating etc.
1760W @ 110V
3680W @ 230V
L
N
NC
S
Zigb ee I n- Wall Switc h
3. Zigbee Network Pairing through Coordinator or Hub (Added to a Zigbee Network)
Step 3: Reset power of the device from
master breaker to set it into network
pairing mode (connected light flashes
twice slowly), the network pairing mode
will last until the device is added to a
zigbee network.

5. Removed from a Zigbee Network through Coordinator or Hub Interface
From your ZigBee controller or hub
interface, choose to delete or reset the
lighting device as instructed. The
connected light blinks 3 times to indicate
successful reset.
Step 4: There shall be
indication on the remote for
successful link and connected
light will flash twice.
Zigbee
Remote < 10cm
Step 2: Bring the remote or
touch panel within 10cm of the
lighting device.
Step 3: Set the remote or touch
panel into Touchlink
commissioning,
please refer to corresponding
remote or touch panel manual
to learn how.
Note: 1) Directly TouchLink (both not added to a ZigBee network), each device can link with 1 remote.
2) TouchLink after both added to a ZigBee network, each device can link with max. 30 remotes.
3) To control by both gateway & remote, add remote and device to network first then TouchLink.
4) After TouchLink, the device can be controlled by the linked remotes.
6. Factory Reset Manually
Step 2: Connected light
will blink 3 times to
indicate successful reset.
Step 1: Short press “Reset.”
key for 5 times continuously
or reset power of the device
for 5 times continuously if
the “Reset” key is not
accessible.
Note: 1) If the device is already at factory
default setting, there is no indication
when factory reset again .
2) All configuration parameters will
be reset after the device is reset or
removed from the network.
7. Factory Reset through a Zigbee Remote (Touch Reset)
Note: Make sure the device already added to a network, the remote added to the same one or not added to any
network.
Step 1: Reset power of the
device to start TouchLink
Commissioning, 180
seconds timeout, repeat
this step.
Step 4: There shall be
indication on the remote and
connected light flashes 3
times for successful reset.
Zigbee
Remote < 10cm
Step 2: Bring the remote or touch
panel within 10cm of the lighting
device.
Step 3: SSet the remote or touch
panel into Touch Reset procedure
to reset the device, please refer to
corresponding remote or touch
panel manual to learn how.
8. Find and Bind Mode
Step 1: Short press “Reset.”
button 3 times (Or reset
power of the device (initiator
node) 3 times) to start Find
and Bind mode (connected
light flashes slowly) to find
and bind target node, 180
seconds timeout, repeat this
step.
Zigbee
Remote
Step 2: Set the remote or touch
panel (target node) into find
and bind mode, and enable it
to find and bind initiator, please
refer to corresponding remote
or touch panel manual.
Step 3: There shall be
indication on the remote or
touch panel that it bind the
device successfully and can
control it then.to learn how.
Note: Make sure the device and remote already added to the same zigbee network.
9. Learning to a Zigbee Green Power Switch
Step 1: Short press
“Reset.” button 4 times
(Or reset power of the
device 4 times) to start
Learning to GP switch
mode (connected light
flashes twice), 180
seconds timeout, repeat
this step.
Zigbee
Green Power
Switch
Step 2: Set the green power
switch into Learning mode,
please refer to its manual.
Step 3: Connected light will
flash twice to indicate
successful learning. Then the
switch can control the device.
Note: Each device can learn to max. 20 zigbee green power switches.
L
N
NC
S
Zigb ee I n- Wall Switc h
L
N
NC
S
Zigb ee I n- Wall Switc h
L
N
NC
S
Zigb ee I n- Wall Switc h
L
N
NC
S
Zigb ee I n- Wall Switc h
L
N
NC
S
Zigb ee I n- Wall Switc h
4. TouchLink to a Zigbee Remote Step 1: Method 1: Short press
“Reset” button 4 times (or reset
power of the device 4 times from
master breaker) to start Touchlink
commissioning immediately under
any circumstances, 180S timeout,
repeat this step.
Method 2: Add the device to a
network, touchlink commissioning
will start immediately after it’s
added to the network, 180S
timeout. Once timeout, reset
power of the device to start
touchlink commissioning again.

L
N
NC
S
Zigb ee I n- Wall Switc h
11. Setup a Zigbee Network & Add Other Devices to the Network (No Coordinator Required)
Step 1: Short press “Reset.”
button 4 times (Or reset
power of the device 4 times)
to enable the device to setup
a zigbee network (connected
light flashes twice) to
discover and add other
devices, 180 seconds
timeout, repeat this step.
Zigbee
Remote
Step 2: Set another device or remote or touch panel into network pairing mode and pair to the network, refer to
their manuals.
Step 3: Pair more devices and remotes to the network as you would like, refer to their manuals.
Step 4: Bind the added devices and remotes through Touchlink so that the devices can be controlled by the
remotes, refer to their manuals.
< 10cm
TouchLink
10. Delete Learning to a Zigbee Green Power Switch
Step 1: Short press “Reset.”
button 3 times (Or reset
power of the device 3 times)
to start delete Learning to GP
switch mode (connected light
flashes slowly), 180 seconds
timeout, repeat this step.
Zigbee
Green Power
Switch
Step 2: Set the paired green
power switch into Learning
mode, please refer to its manual.
Step 3: Connected light will
flash 4 times to indicate
successful deleting.
Note: 1) Each added device can link and be controlled by max. 30 added remotes.
2) Each added remote can link and control max. 30 added devices.
12. OTA
The device supports firmware updating through OTA, and will acquire new firmware from zigbee controller or
hub every 10 minutes automatically.
Wiring Diagram
Notes for the diagrams:
L - terminal for live lead
N - terminal for neutral lead
L1 - output terminals of the device (controlling connected light source)
S - terminal for external switch
NC - No Connection
L
N
1) With Light Load
NC
S
Zigb ee In-Wall Swit ch
L
N
2) Connect With Socket
NC
S
Zigb ee In-Wall Swit ch
GND
NC
S
Zigb ee I n-Wall S wi tch
L
N
NC
S
Zigb ee I n- Wall Switc h

Product Dimension
45.5 mm
20.3 mm
45 mm