Zigen OFL-1000 User manual

OFL-1000
OFL-1000
Uncompressed 4K@60Hz 4:4:4
HDMI Extender over Fiber

Read this user manual carefully before using the product. Pictures shown in this manual
are for reference only. Different models and specifications are subject to real product.
This manual is only for operation instruction, please contact the local distributor for
maintenance assistance. The functions described in this version were updated on
March, 2019. In the constant effort to improve the product, we reserve the right to make
function or parameter changes without notice or obligation. Please refer to the dealers
for the latest details.
FCC Statement
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. It has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a commercial
installation.
Operation of this equipment in a residential area is likely to cause interference, in which
case the user at their own expense will be required to take whatever measures may be
necessary to correct the interference.
Any changes or modifications not expressly approved by the manufacture would void
the user’s authority to operate the equipment.
Preface

To ensure the best performance from the product, please read all instructions carefully
before using the device. Save this manual for further reference.
Unpack the equipment carefully and save the original box and packing material for
possible future shipment.
Follow basic safety precautions to reduce the risk of fire, electrical shock and injury
to persons.
Do not dismantle the housing or modify the module. It may result in electrical shock
or burn.
Using supplies or parts not meeting the specifications of product may cause
damage, deterioration or malfunction.
Refer all servicing to qualified service personnel.
To prevent fire or shock hazard, do not expose the unit to rain, moisture or install
this product near water.
Do not put any heavy items on the extension cable in case of extrusion.
Do not remove the housing of the device as opening or removing housing may
expose you to dangerous voltage or other hazards.
Install the device in a place with fine ventilation to avoid damage caused by
overheat.
Keep the module away from liquids.
Spillage into the housing may result in fire, electrical shock, or equipment damage. If
an object or liquid falls or spills on to the housing, unplug the module immediately.
Do not twist or pull by force ends of the optical cable. It can cause malfunction.
Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to
the device before cleaning.
Unplug the power cord when left unused for a long period of time.
Information on disposal for scrapped devices: do not burn or mix with general
household waste, and please treat them as normal electrical wastes.
Important Safety Instructions

Warranty Information
Powered Product Warranty
Zigen warrants its powered products against any defects in materials and
workmanship for a period of three years from the date of invoice. Touchscreen
displays carry a one year parts and labor warranty. If a malfunction occurs
during the warranty period, Zigen will repair or replace a product to its original
operating condition. A return authorization number must be obtained from
Zigen before products are returned for service.
Non-Powered and Cable Products - Lifetime Limited Performance Warranty
Zigen warrants that its non-powered products and cable products will be free
from defects in material and workmanship for as long as you or your customer
owns the product. All Zigen non-powered products and cables are designed
and engineered to meet and exceed performance specifications. If, at any time,
the product fails due to manufacturer defect, Zigen will repair or replace the
product to ensure that it meets original performance specifications. Reduced
performance due to normal wear and tear, or damages caused by misuse or
negligence will not be covered. Zigen will test and evaluate all non-powered
and cable products claimed defective. Products must be shipped to Zigen,
prepaid along with proof of purchase only after obtaining a Return Merchandise
Authorization (RMA) number from Zigen. This statement of policy is in lieu of
any other policy expressed or implied and no representative or person is
authorized to assume any other liability or adopt any other policy for Zigen
without our written consent.
Return Policy
If you would like to return a Zigen product, it can be done within 30 days of
purchase for a full refund, less shipping and handling. Zigen will not be
responsible for shipping and handling of product returns. Returns will only be
accepted of products with proof of purchase, products in the original packaging
with zero to minimal use and a Return Merchandise Authorization RMA number
provided by Zigen.

Contact Zigen
Technical Support
Tel: (818) 654-5252
Fax: (818) 654-5355
8:00AM - 5:00PM (PST)
Email
Web
www.zigencorp.com
Mailing Address
Zigen Corp.
c/o Customer Service
16135 Wyandotte Street
Lake Balboa CA 91406
USA

1. Product Introduction ...................................................................................................1
2. Specifications .............................................................................................................2
3. Transmitter Description .............................................................................................. 3
4. Receiver Description ..................................................................................................4
5. System Connection .................................................................................................5-7
6. Troubleshooting & Maintenance.................................................................................8
Table of Contents

1
The OFL-1000 is the latest innovative new product from Zigen. 4K/60Hz 4:4:4 HDMI
extender over single MM or SM fiber, with Bi-Directional IR, RS232, Toslink and ARC.
Robust and cost effective - the OFL-1000 is the right HDMI extender for all of your
projects requiring 24/7 flawless operation.
Uncompressed HDMI 2.0a/b 18-G signal up to 300m (1000-ft) from a transmitter to
receiver via multi-mode OM3 or 2km (6500-ft) via single-mode SM fiber. HDCP 2.2
complaint and supports 4K/UHD@60Hz with 4:4:4 chroma sampling, as well as data
rates beyond 18Gbps.
Features
Supports HDMI 2.0a/b and HDCP2.2.
True uncompressed transmission, beyond 18Gbps bandwidth support.
Supports video resolution up to 4K@60Hz with 4:4:4 chroma sampling.
4K@60Hz Dolby Vision, HDR10, HDR-10+ and HLG support.
EDID pass-through.
Full ARC support (up to four modes).
CEC pass-through.
Bi-directional IR and RS232 pass-through.
Up to 300m (1000ft) multi-mode or 2km (6500ft) single-mode on full 4K
Single fiber with LC connector.
Package List
1x Transmitter (Tx)
1x Receiver (Rx)
2x Tx Mounting Ears with 4 Screws
2x Rx Mounting Ears with 4 Screws
4x Plastic Cushions
4x Plastic Cushions
1x Tx Power Adapter (12V DC 1A)
1x Tx Power Adapter (12V DC 1A)
1x RS-232 (DB-9) Cable
1x RS232 (DB-9) Cable
1x User Manual
Note: Please contact your distributor immediately if any damage or defect in the
components is found.
Product Introduction

2
Transmitter (Tx)
Input
(1) HDMI In
Input Connector
(1) Type-A female HDMI
Output
(1) Toslink connector, (1) Audio Out
Output Connector
(2) LC connector; (1) Optical Out
Control 3.5mm
(1) IR In (1) IR Out
Control DB-9 Connector
(1) RS-232
Receiver (Rx)
Input
(1) Toslink connector (1) Audio In
Input Connector
(1) LC connector, (1) Optical In
Output
(1) HDMI Out
Output Connector
(1) Type-A female HDMI
Control 3.5mm
(1) IR In (1) IR Out
Control DB-9 Connector
(1) RS-232
General
Video Resolution
Up to 4Kx2K 60Hz 4:4:4 Dolby Vision
Audio Format
Supports PCM, Dolby Digital, DTS, DTS-HD, Dolby Atmos
HDMI Standard
2.0a/b
HDCP Version
2.2
HDR 10, HDR-10+, HLG
Supported
CEC pass-through
Supported
EDID Bypass
Supported
HPD
Supported
Transmission Distance
≤300m via multi-mode OM3/OM4 fiber cables.
Transmission Distance
≤2000m via single-mode fiber cables.
Operation Temperature
-5℃ ~ +55℃
Storage Temperature
-25℃ ~ +70℃
Relative Humidity
10%-90%
Power Supply
Input: AC 100~240V, 50/60Hz; Output: 12V DC 1A.
Power Consumption
9W (max)
Dimension (W*H*D)
135mm x 20.3mm x 90mm
Net Weight
TX/RX:175g
Specification

3
1. Power LED: The LED illuminates green when power is applied.
Link LED: The LED illuminates green when there is a valid fiber optic
connection with the receiver.
Status LED: The LED illuminates green when the signal data is transmitting
successfully between the transmitter and receiver.
HPD: The LED illuminates green when a source is connected to the
transmitter.
2. Optical Out: LC Fiber Optic output port to connect the Optical In port of
receiver by single-mode fiber or multi-mode fiber.
3. HDMI In: Type-A female HDMI input port to connect the source device.
4. Audio Out (ARC): Toslink digital audio output port for routing multi-channel
audio from receiver to audio amplifier.
5. Audio Mode Selection Switch:
ARC (Default): Switches audio mode to ARC.
Audio: Switches audio mode to audio pass-through (from receiver).
6. IR In: 3.5mm mini jack to connect IR receiver or IR system for IR pass-
through.
7. IR Out: 3.5mm mini jack to connect IR emitter for IR pass-through.
8. RS232: terminal block to connect the RS232 control device (e.g. PC) or a
third-party device to be controlled.
9. FW: Micro-USB port for firmware upgrade ONLY.
10. DC 12V: Locking power port for 12V DC power adapter connection (both Tx
and Rx must be powered individually).
Transmitter Description

4
1. Power LED: The LED illuminates green when power is applied.
Link LED: The LED illuminates green when there is a valid fiber optic
connection with the transmitter.
Status LED: The LED illuminates green when the signal data is transmitting
successfully between the transmitter and receiver.
HPD: The LED illuminates green when a display is connected to the receiver.
2. Optical In: LC Fiber Optic input port to connect the Optical Out port of
transmitter by single-mode fiber or multi-mode fiber.
3. HDMI Out: Type-A female HDMI output port to connect the display device.
4. Audio In (ARC): Toslink digital audio input port for routing multi-channel
audio to transmitter.
5. Audio Mode Selection Switch:
ARC (Default): Switches audio mode to ARC.
Audio: Switches audio mode to audio pass-through (to transmitter).
6. Audio In (ARC): Toslink digital audio input port for routing multi-channel
audio to transmitter.
7. IR In: 3.5mm mini jack to connect IR receiver or IR system for IR pass-
through.
8. IR Out: 3.5mm mini jack to connect IR emitter for IR pass-through.
9. RS232: terminal block to connect the RS232 control device (e.g. RTI XP6) or
a third-party device to be controlled.
10. FW: Micro-USB port for firmware upgrade ONLY.
11. DC 12V: Locking power port for 12V DC power adapter connection (both Tx
and Rx must be powered individually).
Receiver Description

5
Usage Precautions:
Make sure all components and accessories are included before installation.
System should be installed in a clean environment with proper temperature and
humidity.
All power plugs, sockets, and power cords should be insulated and safe.
All devices should be connected before powered on.
There are four ways to route digital audio with the extender system. Below is a chart
indicating the routing status based on the audio mode switch selections on the
transmitter and receiver.
Switch Status
Audio
Transmitter
Receiver
①
ARC
ARC
Audio signal transmitted from smart TV to AV
Receiver/ARC (HDMI In and Audio Out).
②
ARC
Audio
Audio signal transmitted from receiver (Audio In)
to transmitter (HDMI In and Audio Out).
③
Audio
ARC
Audio signal transmitted from receiver/ARC
display connection to transmitter (Audio Out)
only.
④
Audio
Audio
Audio signal transmitted from receiver (Audio In)
to transmitter (Audio Out) only.
Note: When the switch status is set as mode 1, 2 or 3, the amplifier and display must
support ARC and CEC.
System Connection

6
Switch Status ①: Transmitter - ARC; Receiver - ARC
Audio signal transmitted from smart TV to AV Receiver/ARC (HDMI In and Audio
Out).
Switch Status ②: Transmitter - ARC; Receiver - Audio
Audio signal transmitted from receiver (Audio In) to transmitter (HDMI In and Audio
Out).
System Connection

7
Switch Status ③: Transmitter - Audio; Receiver - ARC
Audio signal transmitted from TV to receiver/ARC (Audio Out) only.
Switch Status ④: Transmitter - Audio; Receiver - Audio
Audio signal transmitted to receiver (Audio In) to transmitter (Audio Out) only.
System Connection

8
Problems
Potential Causes
Solutions
Color loss or vague/
double image on display.
Poor quality optical fiber
cable.
OM3/OM4 cable needed.
Power led is off
Not being powered.
Check power source
Poor contact.
Make sure power adapter is
making good contact.
No output on the display.
Source or Display is off.
Check the source/ display.
Poor contact.
Check the HDMI cables one
by one to make sure they are
inserted properly.
The display doesn’t support
the resolution.
Connect the display to the
transmitter and capture its
EDID data before using.
ARC audio is not
received.
CEC or ARC is turned off.
Ensure both CEC and ARC is
enabled on both, display and
as well as AV Receiver.
Note: If you need further assistance, please contact Zigen support Team
Troubleshooting & Maintenance
Table of contents
Other Zigen Extender manuals

Zigen
Zigen ZIG-POC-70L User manual

Zigen
Zigen ZIG-AX Series User manual

Zigen
Zigen ZIG-CX-100 User manual

Zigen
Zigen ZIG-POC-70 User manual

Zigen
Zigen ZIG-HDMI-UCE User manual

Zigen
Zigen ZIG-POC-70U User manual

Zigen
Zigen ZIG-POC-100 User manual

Zigen
Zigen ZIG-PAX User manual

Zigen
Zigen ZIG-AVX-201 User manual