Zintra BEAMS CLOSED RAFTER User manual

PAGE 1
ZINTRA BEAMS
CLOSED RAFTER
zintraacoustic.com
5 X 5
4 X 5
3 X 5
2 X 5
1 X 5

PARTS AND HARDWARE
8in MAIN BEAMS ( 96in / 72in / 48in / 24in )
FOR A TYPICAL ASSEMBLY
PAGE 2
ZINTRA BEAMS
CLOSED RAFTER
zintraacoustic.com
4in CONNECTING BEAM
8in EXTENTION BEAM
8in CORNER BEAM
8in BEAM CONNECTOR
BEAMS CLIP
5 X 5 4 X 5 3 X 5 2 X 5 1 X 5
x8 x5 x4 x3 x2
CLOSED RAFTER VERSION / QTY
x2
x2
x2
x20 x14 x12 x8 x4
x8 x6 x4 x2
x4 x4 x4 x4 x4
x16 x14 x12 x10 x6
x104 x86 x68 x48 x28

PAGE 3
ZINTRA BEAMS
CLOSED RAFTER
zintraacoustic.com
STEP 1
ASSEMBLE INDIVIDUALS PARTS AS PER PURCHASED PACKAGE.
BEAMS ASSEMBLY
FOLD 8IN MAIN BEAM AND SECURE IT BY INSERTING BEAMS CLIPS INTO PRE-CUT RECTANGULAR HOLES.
*BEAMS CLIPS QTY FOR 8IN MAIN BEAMS: *IMPORTANT: DO NOT INSERT CLIPS INTO
FIRST AND LAST HOLES OF THE MAIN BEAM
FOLD 4IN CONNECTING BEAM AND SECURE IT BY INSERTING BEAMS CLIPS INTO PRE-CUT RECTANGULAR HOLES.
*BEAMS CLIPS QTY FOR 4IN CONNECTING BEAM - x2
FOLD 8IN EXTENTION BEAM AND SECURE IT BY INSERTING BEAMS CLIPS INTO PRE-CUT RECTANGULAR HOLES.
*BEAMS CLIPS QTY FOR 8IN EXTENTION BEAM - x1 *IMPORTANT: DO NOT INSERT CLIPS INTO
FIRST AND LAST HOLES OF THE MAIN BEAM
FOLD 8IN CORNER BEAM AND SECURE IT BY INSERTING BEAMS CLIPS INTO PRE-CUT RECTANGULAR HOLES.
*BEAMS CLIPS QTY FOR 8IN CORNER BEAM - x1 *IMPORTANT: DO NOT INSERT CLIPS INTO
FIRST AND LAST HOLES OF THE MAIN BEAM
96IN BEAM - x6; 72IN BEAM - x5; 48IN BEAM - x4; 24IN BEAM - x2.
FOLD 8IN BEAM CONNECTOR AND SECURE IT BY INSERTING INTO PRE-CUT RECTANGULAR HOLES.

PAGE 4
ZINTRA BEAMS
CLOSED RAFTER
zintraacoustic.com
STEP 3
4IN CONNECTING BEAMS INSTALL
3.1 INSERT THE 4IN CONNECTING BEAMS INTO THE
CORRESPONDING PRE-CUT RECTANGULAR HOLES IN
THE 8IN MAIN BEAM.
3.2 AFTER INSERTING, PUSH 4IN CONNECTING BEAM
DOWN TILL YOU HEAR LOCKING SOUND AND TOP
SURFACES ARE FLUSH.
3.3 REPEAT STEPS 3.1 - 3.2 FOR EACH 4IN CONNECTING
BEAM UNTIL THE ASSEMBLY AS SHOWN HAS BEEN
COMPLETED.
STEP 2
DEPENDING ON THE ASSEMBLY DETERMINE HOW MANY BEAMS ARE GOING INSIDE AND HOW MANY OUTSIDE THE ASSEMBLY.
PREPARING 8IN MAIN BEAMS BEFORE ASSEMBLY
2.1 FOR OUTSIDE BEAMS REMOVE PRE-CUT
RECTANGULAR HOLES JUST ON ONE SIDE.
TIP* REMOVE PRE-CUT RECTANGULAR HOLES BY PUSHING THEM INSIDE.
2.2 FOR INSIDE BEAMS REMOVE PRE-CUT
RECTANGULAR HOLES ON BOTH SIDES.
“CLICK”
“CLICK”

PAGE 5
ZINTRA BEAMS
CLOSED RAFTER
zintraacoustic.com
STEP 4
8IN BEAMS CONNECTOR INSTALL
4.1 INSERT 8IN BEAMS CONNECTORS INTO
THE ENDS OF 8IN MAIN BEAMS AS SHOWN.
4.2 WITH THE HELP OF FINGER RISE THE TOP
OF 8IN MAIN BEAM FOR EASY INSERT.
4.3 INSERT THE 8IN BEAMS CONNECTOR INTO
THE CORRESPONDING PRE-CUT RECTANGULAR
HOLES IN THE 8IN MAIN BEAM.
4.4 REPEAT STEPS 4.1 - 4.3 FOR EACH 8IN BEAMS
CONNECTOR UNTIL THE ASSEMBLY AS SHOWN HAS BEEN
COMPLETED.
STEP 5
FINISING INSTALL
REPEATING STEPS 3.1 - 4.4 INSTALL REST
OF THE PARTS OF THE ASSEMBLY AS SHOWN.