Zippity Baskenridge Vinyl Gate Kit w/ Fence Wings User manual

Check Box for These Contents
In the event of missing or defective parts please call our customer service department at 1 877 778 5733 (Mon. to Fri. 8:00 AM to 4:00 PM EST).
1.
Post Caps (6)
2. Horizontal Rails (4) - 1½“ x 1½” x 7 3/8“
3. Posts ( 4) - 7/8” x 1½“ x 44”
4. Gate Posts (2) - 7/8” x 1½“ x 34”
5. Gate Horizontal Rails (1) - 1½” x 1½” x 36“
6. Gate Spindles (8) - ¼” x 1¼“ x 31 ¼”
7. Gate Hardware Kit with Fasteners (1)
8. Corner Brackets (4)
9. 3/4“ Stainless Steel Screws (40) (Bag A)
10. 1“ Self-Tapping Stainless Steel Screws (8) (Bag B)
11. Zippity Connector Brackets (4)
12. 1/8”Drill Bit (1)
Tools You Will Need
• Cordless Drill
• Level
• Shovel
Baskenridge Vinyl Gate Kit w/ Fence Wings
(Unassembled) 51 3/8” Wide x 36” Tall
Please read through before starting assembly.
ASSEMBLY INSTRUCTIONS
1
Not to Scale
IMPORTANT: CHECK THE INSIDE OF THE LARGER PIECES IN YOUR BOX FOR OTHER MATERIALS
PACKED INSIDE.
Ver 1.0/010319
7
This Gate is designed to be integrated with our 36” High Baskenridge Fence
8 9 11
1
5
2
4
6
3
12
1 1/2 in
36 in
36 in
32 1/4 in
31 1/2 in
2 1/4 in
51 3/8 in
8 1/2 in
38 3/4 in
10

2Baskenridge Vinyl Gate Kit w/ Fence Wings Instructions
Baskenridge Vinyl Picket Gate
GENERAL INFORMATION
1 - Read Over Fence Instructions First
Your gate and fence will work better together as an integrated
fence instructions.
2 - Pre-Assemble the Gate Frame
3 - Ideally, Install Your Gate Posts Before Your Fence Posts
Your fence panels will be more forgiving for a custom t than your gate. Ideally, position and install your
gate posts before you do anything else, or very early on in the process of setting up your fence run.
4 - Ideally, Do Not Hang Your Gate System By Itself (With no
other fence panels)
Your gate will perform better and last longer if the fence assembly that supports the hinge side of the gate
is connected in-line with another fence assembly. See illustration below. The weight strain will be transferred
unto two posts versus just one. Installing fence panels on both sides of your gate is the ideal in all situations.
This will ensure three things:
a) That you have everything necessary to complete the gate.
b) That you will have assembled the gate in the correct order.
It’s easier to troubleshoot when things are not screwed together.
d) The gate height and width measure similar to drawing on Page 1.

Use Zippity clips to attach the gate to the fence panel posts.


Assemble the Gate Frame
Orientate the gate posts so the tab is facing up as illustrated.
Insert the post down through one of the gate horizontal rails
as illustrated.
Note: the routed holes for the spindles should be facing down.
Align the pre-drilled holes in the horizontal rail with the pre-
drilled holes in the vertical posts and fasten together with
a total of four 3/4”screws.
Insert spindles into the routed holes in the horizontal rail until
they all click into place.
1
2
STEP ONE
1
3
3
Baskenridge Vinyl Gate Kit w/ Fence Wings Instructions
Note: Routed holes for
spindles should be
facing down.
Tab

2
Align
3

STEP ONE
Assemble the Gate Frame (Cont’d...)
Align and slide a second gate horizontal rail over the posts and
spindles as shown.
Fasten horizontal rail to posts using four 3/4” screws as shown.
Starting with one inside corner, place the corner bracket
against the horizontal and vertical gate posts as shown.
Fasten corner bracket with two 3/4” screws into the horizontal
rail.
Fasten with two more 3/4” screws into the vertical posts.
Repeat for all four inside corners.
4
4Baskenridge Vinyl Gate Kit w/ Fence Wings Instructions
5
5
4
Align
6
7
8
76

5
Baskenridge Vinyl Gate Kit w/ Fence Wings Instructions
STEP TWO
Post Caps, Hinges, and Latch Installation
W
Pressure fit the two caps down over the posts. The post caps
will lock into place.
Align the hinges on the top and bottom horizontal rails as
shown.
Pre-drill two holes on the face of the horizontal rails for each
hinge as shown. Holes should be approximately 1/4” from the
edge of the rail as shown.
Fasten each hinge with two black screws.
Align the finger latch to the top horizontal rail and pre-drill
four holes into the rail as shown.
Fasten four black screws to lock the finger latch in place.
1
2
3
4
5
1
6
5
3
6
4
1/4 in

6Baskenridge Vinyl Gate Kit w/ Fence Wings Instructions
1
2
1
3
Assemble the Gate Wings
Orientate the posts so the tab is facing up as illustrated.
Insert the post down through the two horizontal rails as
illustrated.
Align the pre-drilled holes in the horizontal rails with the
pre-drilled holes in the vertical posts and fasten together with
four 3/4” screws for the bottom rail and four 3/4” screws for
the top rail.
Repeat for second gate wing.
STEP THREE
2
Note the direction
of the spears.
Tab
Align
Align
Align
Align

7
Baskenridge Vinyl Gate Kit w/ Fence Wings Instructions
x
x
x
x
STEP FOUR
Install Gate wings into Ground
1
2
4
3
1
Move the gate wings to their final location and identify the location
of posts.The distance between the posts should be 38 11/16” or
40 3/16“ center-to-center
.
Loosen the top 6” to 8” of the ground using a claw hammer
and screw driver (or something equivalent) as illustrated.
Add water to loosen soil if necessary.
Use a block of wood to the protect the top of post and
gently hammer each post into the ground equally until
bottom rails are about 2”above the ground.
2
3
4
Block of Wood
x
x
x
x
38 11/16”
40 3/16 in
38 11/16 in
x
x
x
x
38 11/16”

8Baskenridge Vinyl Gate Kit w/ Fence Wings Instructions
STEP FOUR
Install Gate wings into ground - continued
Level the assembled unit and backfill and compact dirt around
the base of each post to strengthen the unit.
Finish the assembly by pushing the post caps down over the
top of posts as illustrated. The post caps will lock into place.
5
6
5
6
Level

STEP FIVE
Gate Installation
Align the gate hinges against the horizontal rails of the gate
wing as illustrated.
Mark and pre-drill two holes for each hinge.
Fasten each hinge with two screws.
Align the catch as shown and pre-drill two more holes
into the gate wing horizontal rail.
Fasten two screws to lock the catch in
place.
1
2
3
2
3
99
Baskenridge Vinyl Gate Kit w/ Fence Wings Instructions
5
4
4
5

6935 Reames Rd. Ste. K. Charlotte, NC 28216
Toll Free Phone: [phone] Fax: [phone]
www.zippity-outdoor.com
STEP SIX
10
Fence Panels installation
Follow the instructions included in your Baskenridge Fence kit.
Connect the top and bottom rails of the gate and fence
panels using the supplied zippity clips and 1” self-tapping screws
as shown.
1
2