Zippity ZP19001 User manual

www.zippity-outdoor.com 1
ASSEMBLY
INSTRUCTIONS
MADISON VINYL PICKET FENCE
KIT 2-PACK
60 MINapproximate assembly
time
2 1/2 in
40 in
14 1/8 in14 1/8 in
56 1/2 in
8 1/2 in
16 1/2 in
24 in
2 in
30 in
10 in 28 1/4 in
This fence can easily be trimmed horizontally to t your
custom space. Use a ne-toothed circular saw or hack
saw.
@
6935 Reames Rd. Ste. K. Charlotte, NC 28216
[e-mail]
704-892-5222 / 877-234-6196
zippity-outdoor.com
Want to see a video on how to
assemble this product? Scan
the code below!
Ver. 072320

www.zippity-outdoor.com
2
IMPORTANT
• Please read through before starting assembly.
• Important: Check the inside of the larger pieces in your box for other materials packed inside.
• When assembling components, place on a non-abrasive surface (i.e. shipping box) to avoid scratching.
• We recommend an area approx 5’x 8’ for unobstructed assembling.
• You should not need to use excessive force when assembling components.
VISIT OUR WEBSITE FIRST SO WE CAN HELP YOU RIGHT AWAY!
EMAIL:
WEBSITE:
[e-mail]
nychgroup.com\parts
PHONE: [phone]
To help you quickly and accurately, please have reference item number ZP19001
found on the next page. It is helpful if you can provide the batch lot which is a stamped number on the end of the box.
If you are having problems with the assembly or installation of this product, we are happy to assist you with the process, so
please give us a call at 704-892-5222 / 877-234-6196.
return the product, you will need to initiate the return from the company you originally purchased from.
Although great care has been taken to ensure proper packaging and handling of this product, occasionally problems occur.
If you discover any missing, damaged or defective parts, please visit our website to order replacement parts. If you experi-
ence any further trouble with your product, please contact our customer service department.
Customer service agents are available to take calls weekdays from 8am-5pm EST. If you
call outside of business hours, please leave a voicemail.
GENERAL INFORMATION
MISSING OR DAMAGED PARTS?
NEED ASSEMBLY HELP?
NEED TO RETURN?

www.zippity-outdoor.com 3
STEP 1: LAY OUT MATERIALS
A
C
E F G
D
I
B H
Post Cap (4)
Joiner Clip (4)
0.75” Steel Screw
(24)
Post (4)
⅞” x 1½” x 39½”
Bottom Rail (2)
1½” x 1½” x 56½”
Top Rail (2)
1½” x 1½” x 56½”
Picket #1 (8)
¼” x 1¼” x 25¼”
Picket #2 (8)
¼” x 1¼” x 23”
Picket #3 (8)
¼” x 1¼” x 22”

www.zippity-outdoor.com
4
STEP 2: ASSEMBLE FENCE FRAME
STEP 2.1 Position the two rails as illustrated
and slide two posts (B) through
the large holes in the top (C) and
bottom (D) rails until the pre-drilled
holes in both rails are aligned with
the pre-drilled holes in both posts.
Secure the rails to the post
with screws (I) on both sides
of the rails as illustrated.
Note: Underside of bottom rail is
blank compared to top rail which
has holes on both sides.
Tip: Shine a ashlight down the
end of the posts to help identify
alignment of pre-drilled holes.
Note: Orient the bottom of posts
as illustrated.
C
D
B
STEP 2.2
kçí ÉW=^äáÖå=e çäÉë
Note: Align holes.
I

www.zippity-outdoor.com 5
STEP 3: INSTALL PICKETS
STEP 4: INSTALL FENCE INTO GROUND
Pickets are identied 1 (E),
2 (F), and 3 (G) to create a
scallop pattern as illustrated.
Slide each one down through
the top rail and into the bottom
rail.
Move the fence to its destination,
and identify the location of the
posts.
Attempt to push the product into
the ground as illustrated.
STEP 4.1
STEP 3.1
STEP 4.2
Note: The tabs on the bottom of the pickets
are intended to go into the bottom rail to
lock the picket into place.
Note: To remove a
picket, gently insert
a butter knife into the
bottom rail as shown,
and slowly pull up
the picket.
1
G
FE
x
x
x
x

www.zippity-outdoor.com
6
STEP 4.3 STEP 4.4
STEP 4.5
x
x
Step 4.3 is only to be completed
if ground is too hard.
Option 1: (recommended) Use a
block of wood to protect the top of
the post and gently hammer each
post into the ground.
Option 2: Add water to loosen soil.
Option 3: loosen top 4” of the
ground with a claw hammer as
illustrated.
Level the assembled
unit, and compact dirt
around the base of
each post.
Push the post caps
down over the tops of
the posts as illustrated.
The post caps will lock
into place.
1
2
3
Block of wood
i Éî Éä
Level
x
x

www.zippity-outdoor.com 7
Fasten joiner clips (H) by screwing
them into place on the top of the
rail and the bottom of the rail as
illustrated. Screws are self-drilling.
Fasten the opposite end of the
joiner clip as illustrated.
Top rail
Top rail
Bottom rail
Bottom rail
STEP 5: FASTEN JOINER CLIPS
STEP 5.1
STEP 5.2
H

www.zippity-outdoor.com
8
45 degree application
@
6935 Reames Rd. Ste. K. Charlotte, NC 28216
[e-mail]
704-892-5222 / 877-234-6196
zippity-outdoor.com