Zmotion ZMC308BE User manual

Foreword
The motion controller provides rich interface, and it has excellent motion control performance, which
can meet the expansion requirements of various projects.
This manual is copyrighted by Shenzhen Technology Co., Ltd., without the written permission of the
Zmotion Technology, no person shall reproduce, translate and copy any content in this manual. The
above-mentioned actions will constitute an infringement of the copyright of the company's manual, and
Zmotion will investigate legal responsibility according to law.
For details about the ZMC controller software and the introduction and routine of each command,
please refer to the ZBASIC software manual.
Information contained in this manual is only for reference. Due to improvements in design and
functions and other aspects, Zmotion Technology reserves the final interpretation! Subject to change
without notice!
Pay attention to safety when debugging the machine!
Please be sure to design an effective safety protection device in the machine, and add an error
handling program in the software, otherwise Zmotion has no obligation or responsibility for the loss
caused.
In order to ensure the safe, normal and effective use of the product, please be sure to read this
product manual carefully before installing and using the product.

Safety Statement
⚫This chapter describes the safety precautions required for the correct use of this product. Before
using this product, please read the instructions for use and correctly understand the relevant
information on safety precautions.
⚫This product should be used in an environment that meets the design specifications, otherwise
it may cause equipment damage or personal injury, and malfunctions or component damage
caused by failure to comply with relevant regulations are not within the scope of product quality
assurance.
⚫Zmotion will not take any legal responsibility for personal safety accidents and property losses
caused by failure to comply with the contents of this manual or illegal operation of products.
Safety Level Definition
According to the level, it can be divided into " Danger " and " Caution ". Failure to operate as required
may result in moderate injury, minor injury or equipment damage.
Please keep this guide in a safe place for reading when needed, and be sure to hand this manual to
the end user.
Install
Danger
◆When the controller is disassembled, all external power supplies used by the
system should be disconnected before operation, otherwise it may cause
misoperation or damage to the equipment.
◆It is forbidden to use in the following places: places with dust, oil fume, conductive
dust, corrosive gas and flammable gas; places exposed to high temperature,
condensation, wind and rain; places with vibration and shock. Electric shock, fire
and misuse can cause product damage and deterioration.
Notice
◆Avoid metal shavings and wire ends falling into the hardware circuit board during
installation.
◆After installation, ensure that there are no foreign objects on the hardware circuit
board.
◆When installing, make it tightly and firmly with the mounting frame.

◆Improper installation of the controller may result in misoperation, failure and fire.
Wiring
Danger
◆The specifications and installation methods of the external wiring of the
equipment shall comply with the requirements of local power distribution
regulations.
◆When wiring, all external power supplies used by the system should be
disconnected before operation.
◆When powering on and running after the wiring work is completed, the terminals
attached to the product must be installed.
◆Cable terminals should be well insulated to ensure that the insulation distance
between cables will not be reduced after the cables are installed on the terminal
block.
Notice
◆Avoid metal shavings and wire ends falling into the hardware circuit board during
installation.
◆The cable connection should be carried out correctly on the basis of confirming
the type of the connected interface.
◆It should be confirmed that the cables pressed into the terminals are in good
contact.
◆Do not bundle the control wires and communication cables with the main circuit
or power supply wires, etc., and the distance between the wires should be more
than 100 mm, otherwise noise may cause malfunction.
◆If the controller is not installed properly, it may cause electric shock or equipment
failure or malfunction.

ZMC308BE Motion Controller Hardware Manual V1.5
Content
Chapter I Production Information........................................................................................3
1.1. Product Information ..........................................................................................3
1.2. Function Features..............................................................................................3
1.3. System Frame ...................................................................................................4
1.4. Hardware Installment........................................................................................5
Chapter II Product Specification .........................................................................................7
2.1. Basic Specification............................................................................................7
2.2. Order Information..............................................................................................7
2.3. Interface Definition............................................................................................8
2.4. Work Environment ...........................................................................................10
Chapter III Wiring, Communication Configuration ............................................................11
3.1. Power Input .....................................................................................................11
3.1.1. Power Specification..............................................................................11
3.2. RS485, RS422, CAN Communication Interface...............................................11
3.2.1. RS485, RS422, CAN Communication Specification & Wiring...............12
3.2.2. Basic Usage..........................................................................................15
3.3. RS232 Serial Port ............................................................................................16
3.3.1. RS232 Communication Interface Specification & Wiring ....................17
3.3.2. Basic Usage..........................................................................................18
3.4. IN Digital Input & High-Speed Latch Port .......................................................19
3.4.1. Digital Input Specification & Wiring .....................................................20
3.4.2. Basic Usage..........................................................................................21
3.5. OUT Digital Output, PWM Terminal, Hardware Comparison Output...............22
3.5.1. Digital Output Specification & Wiring...................................................23
3.5.2. Basic Usage..........................................................................................24
3.6. AD/DA Analog Input & Output .........................................................................25

ZMC308BE Motion Controller Hardware Manual V1.5
3.6.1. Analog Input / Output Specification & Wiring ......................................26
3.6.2. Basic Usage..........................................................................................27
3.7. U Disk ..............................................................................................................27
3.8. ETHERNET .......................................................................................................28
3.9. EtherCAT Bus Interface ...................................................................................29
3.10. AXIS Differential Pulse Axis Interface .........................................................31
3.10.1. AXIS Interface Signal Specification & Wiring.......................................33
3.10.2. Basic Usage..........................................................................................35
Chapter IV Expansion Module ...........................................................................................37
4.1. CAN Bus Expansion.........................................................................................37
4.1.1. CAN Bus Expansion Wiring...................................................................37
4.1.2. CAN Bus Expansion Resource Mapping ..............................................39
4.2. EtherCAT Bus Expansion.................................................................................43
4.2.1. EtherCAT Bus Expansion Wiring...........................................................43
4.2.2. EtherCAT Bus Expansion Resource Mapping ......................................44
Chapter V Expansion Module ............................................................................................47
5.1. ZDevelop Software Usage...............................................................................47
5.2. PC Upper-Computer Program Application .....................................................52
Chapter VI Run and Maintain ............................................................................................55
6.1. Regular Inspection and Maintenance .............................................................55
6.2. Common Problems..........................................................................................56

ZMC308BE Motion Controller Hardware Manual V1.5
Chapter I Production Information
1.1. Product Information
ZMC is the abbreviation of the network motion controller model launched by Zmotion
Technology.
ZMC308BE high-performance multi-axis motion controller is a stand-alone motion
controller compatible with EtherCAT bus and pulse type. The controller itself supports
complex continuous trajectory control requirements of up to 16 axes.
ZMC3 series high-performance multi-axis motion controller can be applied in robots
(SCARA, Delta, 6 joints), electronic semiconductor equipment (testing equipment,
assembly equipment, locking equipment, soldering machine), dispensing equipment,
non-standard equipment, printing and packaging equipment, textile and garment
equipment, stage entertainment equipment, medical equipment, assembly line, etc.
1.2. Function Features
◆Motion control of up to 16 axes.
◆Pulse output mode: pulse / direction or dual pulses.
◆Maximum pulse frequency output of each axis: 10MHZ.
◆512 isolation inputs and 512 isolation outputs can be extended at most through
ZCAN bus.
◆Axis position limit signal / origin signal port can be configured as any input at will.
◆The maximum output current of general digital outputs can reach 300mA, which can
directly drive some kinds of solenoid valves.
◆Interfaces: EtherCAT, RS232, RS485, RS422, U Disk, Ethernet.

ZMC308BE Motion Controller Hardware Manual V1.5
◆Support linear interpolation, any circular interpolation and helical interpolation of 16
axes at most.
◆Support electronic cam, electronic gear, position latch, synchronous follow, virtual
axis, etc.
◆Support pulse closed loop, pitch compensation and other functions.
◆Multi-file and multi-task programming in ZBasic.
◆A variety of program encryption methods to protect the intellectual property rights of
customers.
◆Power failure detection and power failure storage.
◆Support 2 precision outputs (OP0/1) and support hardware comparison output
(HW_PSWITCH2).
1.3. System Frame

ZMC308BE Motion Controller Hardware Manual V1.5
1.4. Hardware Installment
The ZMC308BE motion controller adopts the horizontal installation method of screw
fixing, and each controller should be installed with 6 screws for fastening.
→Unit: mm →Installment Hole Diameter: 5.5mm →height: 75mm
Installation
attention
⚫Non-professionals are strictly prohibited to operate. Specifically,
professionals who had been trained related electrical equipment,
or who master electrical knowledge.
⚫Please be sure to read the product instruction manual and safety
precautions carefully before installation.
⚫Before installation, please ensure that the product is powered off.
⚫Do not disassemble the module, otherwise the machine may be
damaged.
⚫Avoid direct sunlight installation.
⚫In order to facilitate ventilation and controller replacement, 2-3cm
should be left between the upper and lower parts of the controller
and the installation environment and surrounding components.

ZMC308BE Motion Controller Hardware Manual V1.5
⚫Considering the convenient operation and maintenance of the
controller, please do not install the controller in the following
places:
a) places where the surrounding ambient temperature exceeds
the range of -20°C-60°C
b) places where the ambient humidity exceeds the range of 10%-
95% (non-condensing)
c) places with corrosive gases and flammable gases
d) places with many conductive powders such as dust and iron
powder, oil mist, salt, and organic solvents

ZMC308BE Motion Controller Hardware Manual V1.5
Chapter II Product Specification
2.1. Basic Specification
Item
Description
Model
ZMC308BE
ZMC306BE
Basic Axes
8
6
Max Extended Axes
16
16
Basic Axes Type
Pulse output, all axes are with encoder, bus axis.
Digital IO
40 inputs, 16 outputs
Max Extended IO
512 inputs, 512 outputs
PWM
4
AD/DA
4 general AD, 0-10V. 2 general DA, 0-10V.
Max Extended AD/DA
128 ADs, 64 DAs
Pulse Bit
32
Encoder Bit
32
Speed Acceleration Bit
32
Pulse Max Frequency
10MHz
Motion Axis Buffer
128
Array Space
160000
Program Space
2MByte
Flash Space
128MByte
Power Supply Input
24V DC input
Communication Interfaces
RS232, ES485, RS422, Ethernet, U disk, CAN, EtherCAT
Dimensions
292mm*188mm
2.2. Order Information
Model
Description

ZMC308BE Motion Controller Hardware Manual V1.5
ZMC308BE
8 axes, point to point, linear, circular, electronic cam, continuous
trajectory motion, robotic car instructions, EtherCAT Bus.
ZMC306BE
6 axes, point to point, linear, circular, electronic cam, continuous
trajectory motion, robotic car instructions, EtherCAT Bus.
ZMC308B
8 axes, point to point, linear, circular, electronic cam, continuous
trajectory motion, robotic car instructions.
ZMC306B
6 axes, point to point, linear, circular, electronic cam, continuous
trajectory motion, robotic car instructions.
2.3. Interface Definition

ZMC308BE Motion Controller Hardware Manual V1.5
→Interface Description
Mark
Interface
Number
Description
POW
Status
Indication
Light
1
Power indicator: it lights when power is
conducted.
RUN
1
Run indicator: it lights when runs normally
ALM
1
Error indicator: it lights when runs
abnormally
RS232
RS232 serial
port (port0)
1
Use MODBUS_RTU protocol
RS485
RS485 serial
port (port1)
1
Use MODBUS_RTU protocol
RS422
RS422 serial
port (port2)
1
Use MODBUS_RTU protocol
EtherCAT
EtherCAT bus
interface
1
EtherCAT bus interface, connect to EtherCAT
bus drive and EtherCAT bus expansion
module
ETHERNET
Ethernet
1
Use MODBUS_TCP protocol, expand Ethernet
through interchanger, the number of net port
channels can be checked through “?*port”,
default IP address id 192.168.0.11
UDISK
U disk
interface
1
Insert U disk equipment
E+24V
Main power
1
24V DC power supplies for controller
CAN
CAN bus
interface
1
Connect to CAN expansion module or
controller.
IN
Digital IO
input
40
Leakage type, internal 24V supply power,
IN0-1 have latch function.
OUT
Digital IO
output
16
Leakage type, internal 24V supply power,
OUT0-1 support hardware comparison
output function, OUT14-15 support PWM
function.
AD/DA
Analog input /
output
1
Resolution: 12 bits, 0-10V
AXIS
Pulse axis
8
Each interface includes differential pulse
output and differential encoder input

ZMC308BE Motion Controller Hardware Manual V1.5
2.4.Work Environment
Item
Parameters
Work Temperature
-10℃-55℃
Work relative Humidity
10%-95% non-condensing
Storage Temperature
-40℃～80℃(not frozen)
Storage Humidity
Below 90%RH (no frost)
vibration
Frequency
5-150Hz
Displacement
3.5mm(directly install)(<9Hz)
Acceleration
1g(directly install)(>9Hz)
Direction
3 axial direction
Shock (collide)
15g, 11ms, half sinusoid, 3 axial direction
Degree of Protection
IP20

ZMC308BE Motion Controller Hardware Manual V1.5
Chapter III Wiring, Communication
Configuration
3.1. Power Input
The power input adopts a screw-type pluggable terminal with a 3Pin pitch of 5.08mm,
which is the power supply of the controller.
→Terminal Definition:
Terminal
Name
Type
Function
E+24V
Input
Power 24V input
EGND
Input
Power ground
FG
Connect to ground
Case Protection Ground
3.1.1. Power Specification
→Specification
Item
Description
Input Voltage
DC24V(-10%~10%)
Opening Current
≤0.8A
Work Current
≤0.7A
Anti-reverse connection
Valid
Overcurrent Protection
Valid
3.2. RS485, RS422, CAN Communication Interface
The communication interface adopts a screw-type pluggable wiring terminal with a 10Pin
spacing of 5.08mm. And this terminal can be shared with controller RS485, RS422 and
CAN communication. It supports MODBUS_RTU protocol and custom communication.

ZMC308BE Motion Controller Hardware Manual V1.5
→Terminal Definition:
Terminal
Name
Function
485B
485-
485A
485+
EGND
External power supply ground
CANL
CAN differential data -
CANH
CAN differential data +
EGND
External power supply ground
422TX-
RS422 send -
422TX+
RS422 send +
422RX-
RS422 receive -
422RX+
RS422 receive +
3.2.1. RS485, RS422, CAN Communication Specification
& Wiring
The RS485 serial port supports the MODBUS_RTU protocol and custom
communication, mainly including 485A, 485B and common port.
The CAN interface of the controller adopts the standard CAN communication
protocol, which mainly includes three ports, CANL, CANH and the common port. And it
supports connecting CAN expansion modules and other standard CAN devices.
RS422 serial port supports MODBUS_RTU protocol and custom communication,
mainly including 422TX-, 422TX+, 422RX-, 422RX+ and common port.
→Specification
Item
RS485
CAN
RS422
Max Communication
Rate (bps)
115200
1M
115200
Terminal Resistor
No
120Ω
/

ZMC308BE Motion Controller Hardware Manual V1.5
Topology
Daisy chain connection structure
Point to point
Nodes can be
extended
Up to 127
Up to 16
Up to 10
Communication
Distance
Longer communication distance, lower communication rate,
max 100m is recommended.
→Wiring Reference
Connect 485A and 485B of RS485 to 485A and 485B of the controller correspondingly,
and connect the common terminal EGND of both parties of RS485 communication
together.
Connect the CANL and CANH of the standard CAN module to the CANL and CANH of
the other side correspondingly. And public ends of the CAN bus communication both
parties are connected together. In CAN bus left and right sides, connect a 120Ωresistor
respectively (please see below graphic).
Connect 422TX and 422RX of RS422 to 422TX and 422RX of the corresponding

ZMC308BE Motion Controller Hardware Manual V1.5
controller, and connect the common terminal EGND of both RS422 communication parties
together.
→Wiring Notes:
⚫As above, the daisy chain topology is used for wiring, so the star topology cannot be
used. When the use environment is ideal and there are few nodes, the branch
structure can also be considered.
⚫Please connect a 120Ω terminal resistor in parallel at the two ends of the CAN bus to
match the circuit impedance and ensure communication stability.
⚫Please be sure to connect the common terminal of each node on the CAN bus to
prevent the CAN chip from burning out.
⚫Please use twisted-pair shielded wires, especially in harsh environments, make sure
the shielding layer is fully grounded.
⚫On-site wiring should also pay attention to the distance between strong current and
weak current wiring, it is recommended to be more than 20cm.
⚫It should be noted that the equipment grounding (chassis) on the entire line must be
good, and the grounding of the chassis should be connected to the standard factory
ground pile.
→Cable Requirements:
Twisted pair shielded wire, and shielded cable grounded.

ZMC308BE Motion Controller Hardware Manual V1.5
3.2.2. Basic Usage
(1) Please follow the above wiring instructions for correct wiring.
(2) After power on, please use ETHERNET or RS232 (default parameter can be connected
directly) to connect to ZDevelop.
(3) Please use the "ADDRESS" and "SETCOM" commands to set and view the protocol
station number and configuration parameters, see "ZBasic Programming Manual" for
details.
(4) Please use the "CANIO_ADDRESS" command to set the master's "address" and
"speed" according to the needs, and use the "CANIO_ENABLE" command to enable or
disable the internal CAN master function, or through "ZDevelop/Controller/State the
Controller/Communication Info” to view the CAN status intuitively, and refer to the
“ZBasic Programming Manual” for details.

ZMC308BE Motion Controller Hardware Manual V1.5
(5) Correctly set the relevant parameters of the third-party equipment according to their
respective instructions to match the parameters of each node.
(6) Correctly set the "address" and "speed" of the slave expansion module according to
the manual of the slave.
(7) After all the settings are completed, restart the power supply of all stations to
establish communication.
(8) Note that the "speed" settings of each node on the CAN bus must be consistent, and
the "address" settings cannot cause conflicts, otherwise the "ALM" alarm light will be
on, and the communication establishment will fail or the communication will be
disordered.
3.3. RS232 Serial Port
RS232 is in a standard DB9 socket and supports MODBUS_RTU protocol and custom
communication.
→Interface Definition:
Terminal
PIN
Name
Type
Function
1、4、
6、7、8
NC
Hang in
the air
Reserved