Znshine Solar Mono-Si Series Guide

正信光电科技股份有限公司
ZNSHINE PV-TECH CO.,LTD
Mounting Manual
INSTALLATION INSTRUCTION FOR DOUBLE GLASS WITH FRAME SOLAR MODULE
Double glass with frame solar modules are made of crystalline solar cells in series with high efficiency, high
transmission and low iron toughened glasses , anti-aging EVA and high flame-resistant back sheet to laminate,
and anodized aluminum alloy frame. Products have high efficiency, lifespan easy installation, high wind
resistance etc.
Products are made according to international standard IEC61215-2016; IEC61730-2016 and have passed
authority test center’s examination. Our products can be used in home roof solar systems, PV stations,
communication stations, petrol, ocean, meteorological, traffic and solar building etc.
Information for installers
Installers must read and understand this manual before installation.
Please ensure that installation, operation and maintenance of your photovoltaic system is only carried
out by qualified persons able to carry out the technical procedures described in this manual, i.e. system planers,
installers and maintenance personnel, and is carried out in accordance with all safety precautions in this manual
and any and all applicable local codes. If you do not possess these qualifications, you may not carry out the work
described herein except for cleaning.
This manual and the instructions set forth herein are part of the product and should therefore be kept for
the entire useful life of the solar installation.
Information for operators
Keep these instructions safe for the entire useful life of the solar installation.
Please contact your plant supplier for information concerning the formal requirements for solar systems.
Please be sure to learn about directives and permit requirements from the responsible local authorities and
energy providers prior to installation of the solar plant.
We recommend that you insure your solar system against natural hazards (e.g. against lightning strikes).

1、Electrical Specification Mono/Poly-Si series
PHOTOVOLTAIC MODULE
Model
ZXM6-LD72
ZXM6-LD60
ZXP6-LD72
Max series fuse rating(A)
15A
Nominal Mass(kg)
26.5kg/25.5kg
18kg/21.5kg
26.5kg/25.5kg
Package Size(mm)
1978x992x25/27/30/35
2000x1002x25/27/30/35
1658x992x25/27/30/35
1678x1002x25/27/30/35
1978x992x25/27/30/35
2000x1002x25/27/30/35
Cell Size
158.75mm×158.75mm/156.75mm×156.75mm
MAX
System voltage
DC1500V
Application class
Class A

●The electrical characteristics are within ±3 percent of the indicated values of Isc, Voc and Pmpp under
test conditions (irradiance of 1000W/cm2,AM1.5 spectrum, and a cell temperature of 25℃)
●Under normal conditions, a photovoltaic module is likely to experience conditions that produce more
current and/or voltage than reported at standard test conditions. Accordingly, the values of ISC and VOC marked
on this module should be multiplied by a factor of 1,25when determining component voltage ratings, conductor
current ratings, fuse sizes, and size of controls connected to the PV output."
●Installation should be in accordance with Australian installation standards AS3000 wiring rules and
AS/NZS 5033.
2、Operating environment
CLIMATE CONDITION
Install the PV module in the following conditions:
●Environment temperature：-20℃to 40 ℃。
●Operating temperature：-40℃to 80 ℃。
●Waterproof: don’t dip the modules into the water or continually explode under the water device or
fountain.
●Antisepsis: keep away from salt erode and sulfuration places
●Do not wear rings, jewelry, watches or other metallic items while working with photovoltaic
modules.
3、Mounting and notes
●The modules’ electrical performance in a system is the same. When connected in series, all modules
must have the same amperage. When connected in parallel, the modules must all have the same voltage.
Connect the quantity of modules that match the voltage specifications of the devices used in the system.
The modules must not be connected together to create a voltage that is higher than the permitted
system voltage.
●To minimize risk in the event of an indirect lightning strike, avoid forming loops when designing the
system.
●Modules must not be fitted as overhead glazing. Ensure that the mounting system can also withstand
the anticipated wind and snow loads.
●Precipitate can run off through small openings on the back side of the module. Make sure that the
openings are not masked after mounting.
●The modules have passed mechanical load test 5400Pa,To avoid exceeding the maximum load,
site-specific live loads such as wind and snow should be taken into account.

●The installation of project must be facing north in the southern hemisphere, and facing south in the
northern hemisphere, the electricity will be comparatively lower when the project facing west or east.
The incorrect installation will lead to the loss of power
●The modules, which are connected in series, must be in the same angle, otherwise, it will lose power
because of the difference in sunlight intensity. Solar modules generate the power to the maximum when
they are pointed directly at the sun. For installations where the solar modules are mounted to a
permanent structure, the solar modules should be tilted for optimum winter performance. As a rule, if
the system power output is adequate in the winter, it will be satisfactory during the rest of the year. The
module tilt angle is measured between the solar modules and the ground.
●Avoid installing under the shadow, even the module factory use the bypass diode to decrease the loss of
energy, the shadow will lead to the loss of output power.
4、Grounding
●All module frames must be attached to an earth ground. A qualified electrician must do the ground
connection .The cable which connects the earth must be copper wire with 12AWG.
RECOMMENDED TILT ANGLES FOR A FIXED SYSTEM
SITE LATITUDE IN DEGREES
FIXED TILT ANGLE
0oTO 15 o
15 o
15oTO 25o
SAME AS LATITUDE
25oTO 30o
LATITUDE+5 o
30oTO35o
LATITUDE+10 o
35oTO 40o
LATITUDE+15 o
40o+
LATITUDE+20 o

●Use the holes(5.0mm) marked ' '. To create the conductive connection (frame is anodized), use
Stainless steel M5nut, two Stainless steel cut washer, Stainless steel M5 plain washer, Stainless steel
M5 spring washer , M5 copper wire ,and Stainless steel M5 bolt.
1. Copper wires with M5 cupped washer should be placed through the bolt;
2. Put the cut washer through the bolt, and the bolt must be put through the hole fixed in the aluminum
frame;
3. Use the nut and cut washer to fix all the parts. The copper wire can not be attached to the aluminum.
●Do not interrupt or influence the conductive connection when making daily maintenance .All the
crunodes on the conductive connection must be fixed. The fastness does not depend on soldering.
5、Suggested maximum number of modules in parallel and in series
●When designing the system, we Suggested maximum number of modules in parallel and in
series for [Vsys/(1.25Voc)]/1、fuse rating/Isc+1.

6、Mounting
Clamping installation
Modules can be installed with clamps. Modules must be securely attached to the mounting structure with four
clamps on the long frame.
The modules must be properly secured to their support so that they can withstand live load condition,
including wind uplift, to the pressure they have been certified for. It’s the installer’s responsibility to ensure
the clamps used to secure the modules are strong enough.
The modules are not subject to wind or snow loads exceeding the maximum permissible loads.
The module clamps which are used must not come into contact with the front glass and must not deform
the frame. Avoid shadowing effects from the module clamps. Drain holes in the module frame must not be
closed or obscured by the clamps.
The module installed with clamps on the front frame for load (see the following picture), and refer to the
following table.
Mechanical load
pressure
Clamps
Width
Installation direction
+2400Pa/-2400Pa
（4clamps with 2
rails）
≥80mm
+2400Pa/-2400Pa
（4clamps with 2 rails）
150mm

+5400Pa/-3600Pa
（6 clamps with 3 rails）
≥150mm
Use a torque wrench for installation, and the compression for each clamps is not strong to avoid potential
damages to module frames. The recommended maximum compression for each clamp is 20MPa (2900PSI).
The module mounting structure must be made of durable, corrosion-resistant and UV-resistant material. All
mounting hardware (bolt/flat washer/split washer/nut) should be stainless steel M8 size.
The minimum recommended length for each clamp is 60mm.
The modules have been designed to resist a static load, and the resistance value can decrease if modules are
not mounted following the instruction above.
This manual is just for reference. Customer can select the corresponding installation manual based on the
purchased module.

7、Wiring
●The modules use the PV-JX1203 type junction box. This box, on the back side of the module, is
weatherproof and is designed to be used with standard wiring or conduit connections. Wiring methods
should be in accordance with the NEC (National Electrical Code). Bypass diodes and cable clamps are
included with each module when shipped from the factory.
●Correct wiring scheme
When designing the system, avoid forming loops to minimize risk in the event of an indirect lighting
strike. Check that wiring is correct before starting the generator. If the measured open circuit voltage
( Voc) and short-circuit current (Isc) differ from the specifications, then there is a wiring fault.
●Correct connection of contact plug connectors
The plug connector has its own polarity. Make sure that the connection is safe and tight. The plug
connector should not receive outer stress. Otherwise, it is only used to connect the circuit!
●Use of suitable material
Use cable extensions and plugs that are designed for outdoor application. Ensure that they are in perfect
electrical and mechanical condition. Use only cables having one conductor. Select the appropriate cable
diameter to minimize voltage drop (to calculate the minimum cable diameter and the fuse, and to
calculate controls, multiply the Isc and Voc by a factor of 1.56).
If the module is connected to the control box, you must choose the control box with LJQ-1、LJQ-3 type
Connectors.
8、Maintenance and cleaning
●Do not change the PV components optionally (diode, junction box, plug connectors )
●Given a sufficient tilt (at least 15°), it is not generally necessary to clean the modules (rainfall will have a
self-cleaning effect). In case of heavy soiling (which will result in output reductions), we recommend cleaning the
modules using plenty of water (from a hose) without cleaning agents and using a gentle cleaning implement (a
sponge). Dirt must never be scraped or rubbed away when dry, as this will cause micro-scratch. We recommend
that the system be inspected at regular intervals.
9、Checklists:
●All fastenings are tight and secure and free of corrosion.
●All cable connections are secure, tight, clean and free of corrosion.
●Cables are not damaged in any way.
●Check the earthing resistive of metals.

10、Danger of death from electric shock!
Solar modules generate electricity as soon as they are exposed to light. One module on its own
is below the safety extra low volt level, but multiple modules connected in series (summing the voltage)
or in parallel (summing the current) represent a danger. The following points must be observed when
handling the solar modules to avoid the risk of fire, sparking and fatal electric shock.
●Do not insert electrically conducting parts into the plugs or sockets!
●Do not fit solar modules and wiring with wet plugs and sockets!
●Exercise utmost caution when carrying out work on wiring and safety equipment (use insulated
tools, insulated gloves, etc.)!
●Do not use damaged modules! Do not dismantle modules! Do not mark on the rear of the
module using sharp objects!
●Exercise utmost caution when working on wiring and the inverter. Be sure carefully to follow
manufacture’s installation instructions!
●Artificially concentrated sunlight shall not be directed on the modules or panels!
11、Danger of death from arcing！
Modules generate direct current when light shines on them. An arc may be produced when
connections are separated. We therefore recommend covering modules with a lightproof cloth during
installation. When breaking a connected string of modules (e.g. when disconnecting the DC line from
the inverter under load), a lethally strong arc can occur:
●Never disconnect the solar generator from the inverter while the inverter is connected to the
mains grid—remove the fuse from the AC side on the inverter first!
●Ensure cable connections in perfect condition (no splitting, soiling or other contamination)!
Remark: all sizes are measured in mm; and tolerance +/- 2 mm
12、Specification for solar module barcode
●Bar code compiling regulation: company two letters with 14 numbers to make the code, (except for
that client asked for special requirement), a total of 16;

ZX X X X X XX XX XX XXXX
flow coding (4digit)
production date (2digit)Two numbers minus 12 is the actual date
production month (2digit)Two numbers minus 18 is the actual
Producing year (2digit)Two numbers minus 15 is the actual year
Department No.1,2,3,4 stands for Znshine Factory
The very day order time(1-9according to the sequence)
1 as mono panels doped with boron, non-coated glass
2. 2 as poly panels, non-coated glass;
5 as mono panels doped with gallium, non-coated glass;
7 as mono panels doped with boron, coated glass
8 as poly panels, coated glass;
9 as mono panels doped with gallium, coated glass;
第 11.12 位数字码
第 9、10 位数字码
第 6 位数字码
第 7、8 位数字码
第 5 位数字码
第 3 位数字码
第4位数字码
第 1、2 位数字码
PV modules were manufactured by ZNshine ZNSHINE
PV-TECH Co., Ltd. （ No.1 ， South Zhenxing Road ，
Industrial Zone ， Zhixi Town ， Jintan District ，
Changzhou City ,Jiangsu Province,China）
Not free from PID/ Free from PID (one number):
0 represents for 3BB modules which are not free from
PID;
1 represents for 3BB modules which are free from PID;
2 represents for 4BB modules which are not free from
PID;
3 represents for 4BB modules which are free from PID;
4 represents for 5BB modules which are not free from
PID;
5 represents for 5BB modules which are free from PID;
6 represents for 12BB modules which are not free from

12 TECHNICAL DATA
组件系列
Module Series
72pcs 158.75×158.75mm Monocrystalline Silicon Module
尺寸（mm）/重量（kg）
Dimensions(mm)/ Weight(kg)
2000x1002x25/27/30/35
系统电压（VDC）
Max-System Voltage (VDC)
1500
最大保险丝额定电流（A）
Max-Series Fuse(A)
15
电气参数（标准测试条件下）
Electrical Performance @ STC
组件类型
Model Type
ZXM6-LD72-380
/M
ZXM6-LD72-385
/M
ZXM6-LD72-390/
M
ZXM6-LD72-395
/M
最大功率
Max-Power Pm(W)
380
385
390
395
最大功率点的工作电压
Max-Power Voltage Vmp(V)
39.8
40
40.2
40.4
最大功率点的工作电流
Max-Power Current Imp(A)
9.55
9.63
9.71
9.78
开路电压
Open Circuit Voltage Voc(V)
48.5
48.7
48.9
49.1
开路电流
Short Circuit Current Isc(A)
10.04
10.10
10.17
10.25
组件系列
Module Series
60pcs 158.75×158.75mm Monocrystalline Silicon Module
尺寸（mm）/重量（kg）
Dimensions(mm)/ Weight(kg)
1678x1002x25/27/30/35
系统电压（VDC）
Max-System Voltage (VDC)
1500
最大保险丝额定电流（A）
Max-Series Fuse(A)
15
电气参数（标准测试条件下）
Electrical Performance @ STC
组件类型
Model Type
ZXM6-LD60-315/M
ZXM6-LD60-330/M
最大功率
Max-Power Pm(W)
315
330
最大功率点的工作电压
Max-Power Voltage Vmp(V)
33
33.4
最大功率点的工作电流
Max-Power Current Imp(A)
9.55
9.74

开路电压
Open Circuit Voltage Voc(V)
40.2
40.6
开路电流
Short Circuit Current Isc(A)
10.05
10.25
组件系列
Module Series
72pcs 156.75×156.75mm Polycrystalline Silicon Module
尺寸（mm）/重量（kg）
Dimensions(mm)/ Weight(kg)
1978x992x25/27/30/35
系统电压（VDC）
Max-System Voltage (VDC)
1500
最大保险丝额定电流（A）
Max-Series Fuse(A)
15
电气参数（标准测试条件下）
Electrical Performance @ STC
组件类型
Model Type
ZXP6-LD72-345/P
ZXP6-LD72-350/P
ZXP6-LD72-355/P
最大功率
Max-Power Pm(W)
345
350
355
最大功率点的工作电压
Max-Power Voltage Vmp(V)
38
38.2
38.4
最大功率点的工作电流
Max-Power Current Imp(A)
9.08
9.17
9.25
开路电压
Open Circuit Voltage Voc(V)
47.3
47.5
47.7
开路电流
Short Circuit Current Isc(A)
9.34
9.42
9.50
Website：www.znshine.com
Address：#1 Zhixi Industry Zone, 213251 Jintan, Jiangsu, PEOPLE’S REPUBLIC OF CHINA
Tel ：[phone] Fax ：[phone]