Thank you for your purchase of this quality Zojirushi product. We are
confident that it will give you top performance and optimum satisfaction
for many years. To ensure this, please read and follow the important
guidelines below.
Name of Each Part:
How to Remove/Place the Gasket and Valve:
How to Use:
1. Remove inner bowls
Unlock the sides, remove outer lid, and
take out inner bowls from outer container.
4. Fill main bowl
Fill the main bowl with hot (cold) food,
close the inner lid and place in the outer
container.
＊When closing the inner lid, make sure
the triangle mark on the lid aligns with
the tab mark.
6. Lock the lid on the outer
container and place in
carrying bag
＊Place the forked spoon in the
forked spoon holder of the
carrying bag.
2. Preheat
(
Precool
)
a. For maximum heat (cold) retention, fill outer
container, main bowl and soup bowl with hot
water
(cold water)
for 1-2 minutes.
b.
After preheating (precooling), discard the hot
water (cold water) and wipe with soft cloth.
3. Fill soup bowl
Fill the soup bowl with hot
(cold) soup, close the
inner lid tightly and place
in the outer container.
Cautions:
How to Take Care of your Lunch Jar:
For Odor Problems:
Valve Packing
The valve packing is on the center of the inner lid.
To remove, pull the valve packing off with your
fingers. Please replace the valve packing after
cleaning. Please take caution not to scratch the
valve with your fingernails.
Product Name
Model No. SL-JAE14
Capacity
Stainless Lunch Jar
Main Bowl
15.2 oz.(0.45L)
Side Bowl(lg)
10.1oz.(0.3L)
Side Bowl(sm)
6.8 oz.(0.2L)
Soup Bowl
9.5 oz.(0.28L)
a
b
＊Do not soak.
＊Do not place in dishwashers or dryers.
＊Do not clean with thinner, benzene, bleach, abrasive cleaners or other
harsh cleaners.
＊Do not bleach.
For questions or comments, please contact:
Zojirushi America Corporation
Tel: (800)733-6270
www.zojirushi.com
Outer Lid
Inner Bowls
Forked Spoon Cover
Outer Container
Inner Bowls
Soup Bowl
Outer Container
Inner Lids
Forked Spoon
Carrying Bag
If the jar is kept unwashed for a long period of time or is not cleaned thoroughly,
the inner bowls may smell or discolor. In this case, please follow these
instructions.
Wash with warm water and dishwashing soap, rinse and dry
with a soft cloth.
・Do not soak.
Wipe with a damp cloth with warm water and dishwashing
soap.
Boil the inner bowl for 2-3 minutes in hot water and dry as
directed above.
Outer Lid
Inner Lid (sm)
Side Bowl (sm)
Side Bowl (lg)
Lock
Main Bowl
Inner Lid
Main Bowl
Forked Spoon
Holder
Forked Spoon
Forked Spoon Cover
Carrying Strap
Zipper
Outer
Container
Carrying
Bag
Soup Bowl
Inner Lid
Valve Packing
Gasket
Soup Bowl
Inner Lid (lg)
Unlock
Open
Open
Close
5. Fill the side bowls
Fill the side bowls and close the inner lid. Place in
the outer container.
＊Please place inner bowls in the following order:
Soup Bowl→Main Bowl→Side Bowl(lg)→Side Bowl(sm)
Unlock
■
Keep out of reach from infants.
■
Keep away from heat sources such as gas stoves, ovens and heaters.
■
When placing inner bowls in the microwave, please:
・Remove all lids from inner bowls.
・Do not microwave outer container.
・Do not microwave the inner bowls when there is nothing inside.
■
Do not leave the lunch jar on its side (contents may spill).
■
Do not leave food in lunch jar for a long period of time for it may spoil.
Do not include foods that spoil easily such as dairy products.
■
Please avoid storing liquids in the main bowl or side bowls for contents
may spill.
■
Do not place any food directly in the outer container.
■
Clean the inside of the outer container to avoid rusting.
■
Do not carry by the lid.
■
Avoid dropping or hitting against hard surfaces.
■
Consume foods within 6 hours to keep foods from spoiling.
■
Cool foods before storing in the side bowls to prevent from spoiling.
■
Closing the lid while the content is hot may deform the lid and cause spilling.
■
Do not put hot food and cold food in the main bowl and soup bowl, or
hot food and cold food in one bowl at the same time (contents may spoil).
Mr. Bento
TM
Stainless Lunch Jar
SL-JAE14
Instruction Manual
Wash thoroughly and dry with a soft cloth. Place in the sun
and let dry for 1-2 hours.
Gasket
a. To Remove: Remove the gasket from the
inside by using a pin or a small object and
fitting it into the small openings.
b. To Place: Fit the gasket around the inside of
the inner lid by pushing it in with your fingers.
Wash with warm water and dishwashing soap, rinse and dry.
・Remove and wash the gasket and valve after each use.
・Remember to replace the gasket and valve packing after
washing.
・Remove lid while drying.
a
b
0.45L
(15.2 oz.)
0.3L
(10.1 oz.)
0.2L
(6.8 oz.)
0.28L
(9.5 oz.)
・・・・
・・・・・
・・・・・
・・・・・・・・・
SL-JAE14
SL-JAE14
