ZoneVu FUSION-AUDIT-ZVK User manual

FUSION-AUDIT-ZVK INSTALLATION GUIDE
FUSION-AUDIT-ZVK
FUSION-AUDIT-ZVK Installation Guide
Issue 01

Contents
INTRODUCTION ......................................................................................................................................................................................................... 3
FUSION-AUDIT-ZVK OVERVIEW .............................................................................................................................................................................. 4
INSTALLATION........................................................................................................................................................................................................... 5
CONFIGURATION MODE........................................................................................................................................................................................... 7
REGISTRY CONFIGURATION ................................................................................................................................................................................... 9
ZSC-1000PLUS CONFIGURATION.......................................................................................................................................................................... 10
USER CONFIGURATION.......................................................................................................................................................................................... 11
ZVK CONFIGURATION ............................................................................................................................................................................................ 12
LOGGED COMMANDS............................................................................................................................................................................................. 13
REQUIRED SOFTWARE .......................................................................................................................................................................................... 14
SERVICING AND SUPPORT.................................................................................................................................................................................... 15
WARRANTY.............................................................................................................................................................................................................. 16
MINIMUM SYSTEM REQUIREMENTS..................................................................................................................................................................... 18
APPENDIX A............................................................................................................................................................................................................. 19
MEYERTECH LIMITED


FusionAlarm Installation Guide Issue 01 Page 3 of 21
Introduction
Thank you for purchasing Meyertech’s FUSION-AUDIT-ZVK
software. Please read this user guide prior to using FUSION
Audit ZVK.
What is FUSION-AUDIT-ZVK?
FUSION-AUDIT-ZVK is a software application developed
by Meyertech, which will provide an auditable log of activities
on Meyertech ZVK keyboards, 3rd parties connected to
ZSC-250s, Internal events on the ZSC such as alarms,
alarm events, timed events and sequences without the
requirement of running FUSION.
FUSION-AUDIT-ZVK communicates with the CCTV
systems Site Controller to produce a log of operator
activity when using Meyertech’s Site mode and Classic mode.
The information in this manual is believed to be accurate and reliable. However,
Meyertech Limited assumes no responsibility or liability for its use, or for any
infringement of patents or other rights of third parties, which may result from its
use. No license is granted by implication or otherwise under any patent or other
rights of Meyertech. All specifications are subject to change without prior notice.
MEYERTECH LIMITED are committed to continuous product development and
therefore reserve the right to change specifications without notice.
©2005-6 ALL RIGHTS RESERVED.
KEY FEATURES
•
Command auditing of the Meyertech
keyboards, 3rd Party connections, Alarms,
A
larm Events, Timed Events and
Sequences
• FusionAudit compatible
• Fusion compatible
• Will operate as a background process on
your Management PC or Fusion WS
The features described in this manual refer to :
Version 1.0.0.0 of the FUSION-AUDIT-ZVK Application
Meyertech, the Meyertech logo, Security with Vision, FUSION, the FUSION logo, ZoneVu, the ZoneVu logo are either registered trademarks
or trademarks of Meyertech limited incorporated in the United Kingdom and/or other countries.
MEYERTECH LIMITED

FUSION-AUDIT-ZVK Installation Guide Issue 01 Page 4 of 21
FUSION-AUDIT-ZVK Overview
Workstation RS232 serial ports
Access is required to a dedicated serial port, through which the application communicates with the Meyertech Site Controller.
See installation diagram overleaf.
Operating Mode
FUSION-AUDIT-ZVK is an application that operates in the background on your PC or Workstation.
Once the application is configured and running no user input is required.
IMPORTANT !
Logging of keyboard activity will only occu
r
whilst the Fusion Command Audit application i
s
running.
MEYERTECH LIMITED
FUSION-AUDIT-ZVK

FUSION-AUDIT-ZVK Installation Guide Issue 01 Page 5 of 21
Installation
ZSC-1000
ZoneVu
FUSION-WS
Fusion Audit ZVK
and Fusion Audit
ZVK-77
ZVK-77
RS232
Basic Installation - No Fusion Workstations
ZSC-1000
ZoneVu
FUSION-WS
FUSION
ZVK-77
ZVK-77
RS232
Advanced Installation - Fusion Workstations
ZSC-250
ZoneVu FUSION-WS
FUSION
Fusion Audit ZVK
FUSION-WS
FUSION-AUDIT-ZVK
FusionAudit
Ethernet
PC2ZVK
PC2ZVK
RS232
RS232
RS232
MEYERTECH LIMITED

FUSION-AUDIT-ZVK Installation Guide Issue 01 Page 6 of 21
Background Mode
In this mode, the application is generating a log of all the relevant operator commands.
The commands are stored in a file that is understood by FusionAudit. FusionAudit, running independently will import and
truncate this log to produce the audit log.
Current Status
This dialog will report the current status of the connection between FUSION-AUDIT-ZVK and the Meyertech ZoneVu CCTV
system.
User Options
Before any user options can be selected, the operator must Log On. Log On is restricted to Manager and Engineer level
user accounts.
Log On – Use this button to display the Log On dialog.
FUSION-AUDIT-ZVK
Log Off – Use this button to Log Off and return FUSION-AUDIT-ZVK to its background operating mode.
Configuration – Use this button to display the configuration dialog (see next section).
Exit – Use this button to exit the application. Once the application is closed, keyboard activity will no longer be logged.
MEYERTECH LIMITED

FUSION-AUDIT-ZVK Installation Guide Issue 01 Page 7 of 21
Configuration Mode
Configuration mode is selected from background mode, by logging on then selecting the configuration option.
Only those operators of the correct login priority will be allowed to access the configuration.
Workstation
This number identifies the FUSION-AUDIT-ZVK application as a virtual workstation. It should therefore be different to any
other Fusion Workstations on the CCTV system. See the Registry Configuration section for further details.
Comm Port
A free serial communications port must be dedicated for use by FUSION-AUDIT-ZVK. See the Registry Configuration section
for further details.
User Configuration
This section is reserved for future development.
MEYERTECH LIMITED
FUSION-AUDIT-ZVK

FUSION-AUDIT-ZVK Installation Guide Issue 01 Page 8 of 21
MAC Address Barring
This section allows the user to specify which MAC addresses should not be audited by FUSION-AUDIT-ZVK. This is done
via the MAC Address Barring dialog.
This screen lists the available MAC addresses on the system. For each of the available MAC addresses there is a tick box
which the user can use to specify whether the selected MAC address is audited.
Once changes have been made the user can either save the changes and exit the dialog or exit without saving.
MEYERTECH LIMITED
FUSION-AUDIT-ZVK

FUSION-AUDIT-ZVK Installation Guide Issue 01 Page 9 of 21
Registry Configuration
The two registry entries that need to be configured for FUSION-AUDIT-ZVK can be modified by using the registry editor. The
registry editor can be launched by selecting the Start Menu in Windows and then clicking “Run…”
From the run prompt, type “Regedit.exe” to launch the registry editor.
The registry values that may need to be modified can be found under the following registry key:
HKEY_CURRENT_USER\Software\Meyertech\FUSION-AUDIT-ZVK
The registry values within this key are as follows:
Registry Key Description Default setting
Communications\Port Communications port 1
Workstation\Number Workstation number to use for Audit files 1
WARNING !
Editing the registry can cause problems to th
e
system. These steps must only be completed b
y
a competent computer user.
MEYERTECH LIMITED
FUSION-AUDIT-ZVK

FUSION-AUDIT-ZVK Installation Guide Issue 01 Page 10 of 21
ZSC-1000plus Configuration
The PC2 port of the ZSC-1000plus site controller must be enabled for use with FUSION-AUDIT-ZVK.
This is done using Meyertech’s Mpower software to select the “Audit Mode” option on the PC2 port. The default baud rate of
9600 baud should also be selected.
Please refer to the ZSC-1000plus and Mpower manuals for further details.
MEYERTECH LIMITED
FUSION-AUDIT-ZVK

FUSION-AUDIT-ZVK Installation Guide Issue 01 Page 11 of 21
User Configuration
In order for FUSION-AUDIT-ZVK to effectively audit a CCTV system it is very important to ensure that the user lists are
synchronised correctly between the keyboard and FusionAudit.
To synchronise the users from the Fusion user list to FusionAudit is a two step process. Firstly the user list has to be
exported using FusionEdit. This is done in the operator configuration screen by clicking the button in the FusionAudit section
labelled “Synchronise”.
Secondly, the user list must be imported into FusionAudit. This is done in FusionAudit via Database Administration ÆSystem
tab ÆFusion Users Synchronisation. Once the synchronise button is pressed FusionAudit will complete the synchronisation
process.
Please refer to the FusionAudit and FusionEdit manuals for further details.
WARNING !
It is essential that the above tasks are done i
n
the order that is stated. Firstly, synchronise fro
m
FusionEdit and secondly synchronise fro
m
FusionAudit.
MEYERTECH LIMITED
FUSION-AUDIT-ZVK

FUSION-AUDIT-ZVK Installation Guide Issue 01 Page 12 of 21
ZVK Configuration
While FUSION-AUDIT-ZVK will audit any Meyertech ZVK keyboard it is important to note that only the ZVK-77D supports
User Synchronisation. This means that while the ZVK-77D will log commands associated with a particular user, other
keyboards will log commands associated with the actual keyboard itself (keyboards 1-12 are supported).
The User Logins on the ZVK-77D keyboards can be synchronised with FusionAudit for use with FUSION-AUDIT-ZVK.
In Mpower the operator information can be added manually or imported using a Fusion operator data file. Please refer to the
ZVK-77D and Mpower manuals for further details.
MEYERTECH LIMITED
FUSION-AUDIT-ZVK

FUSION-AUDIT-ZVK Installation Guide Issue 01 Page 13 of 21
Logged Commands
FUSION-AUDIT-ZVK generates FusionAudit compatible log files. If all applications are correctly configured and synchronised
then a full audit of the operator commands on the ZVK keyboards, when running in either PCI or Classic mode, will be
produced.
Below is a table detailing those operator commands that are logged.
User Operation Notes
Operator Commands
Log On
Log Off
Camera Selected
Selected
Controlled
Submit
Deny
Assert Additional FusionAudit configuration required
Relinquish Additional FusionAudit configuration required
Trunk (remote site)
Grant
Deny
Submit
Application
Start
Exit
Sequence
Start
Release
Forward
Backward
Pause
Continue
Camera Alarms
Accept
Active
Clear
Panel Alarms
Accept
Active
Clear Additional FusionAudit configuration required
Peripheral Alarms
Accept
Active
Clear
FUSION-AUDIT-ZVK
MEYERTECH LIMITED

FUSION-AUDIT-ZVK Installation Guide Issue 01 Page 14 of 21
Required Software
The following software versions are required from Meyertech for FUSION-AUDIT-ZVK.
FusionAudit 1.6.1.0 and Later
This will be used to synchronise the user lists and will be used to view the data that is gathered by FUSION-AUDIT-ZVK.
FUSION-AUDIT-ZVK 1.0.0.0 and Later
This will be used to audit the CCTV network.
FusionEdit 1.18.0.0 and Later
This will be used to synchronise the user lists with FusionAudit.
Mpower 2.20.0.0 and Later
This will be used to synchronise the ZVK-77D user lists with the Fusion user lists and will also be used to set the ZSC-1000
into audit mode.
MEYERTECH LIMITED
FUSION-AUDIT-ZVK

FUSION-AUDIT-ZVK Installation Guide Issue 01 Page 15 of 21
Servicing and Support
Servicing
See your FUSION manual.
Returns Procedure
See your FUSION manual
Support
Meyertech offer comprehensive levels of support during the product’s warranty period. Our support team will be happy to
help with any problem you may experience relating to the installation or operation of FUSION-AUDIT-ZVK.
1. Telephone support (+44(0)161 628 8406 ), which is available during normal office hours 9AM – 5PM Monday to
Friday excluding Bank holidays. This support is free of charge.
2. Email support. Available 24 hours a day. Our normal response to emails is next working day. This support is free of
charge. support@meyertech.co.uk
3. By Facsimile (+44(0)161 628 9811). Available 24 hours a day. Our normal response to facsimiles is next working
day. This support is free of charge.
4. Site visits. Subject to availability, our engineers are available to attend site to assess and help with particular system
problems firsthand. This service is chargeable. Please contact our Support department on +44(0)161 628 8406 for
further details and availability.
Meyertech offer Extended Support Contracts on all their software products. Please contact our Sales department on 0161
628 8406 to discuss your requirements or visit our website www.meyertech.co.uk
Meyertech Limited
Office Block One
Southlink Business Park
Oldham
OL4 1DE
Tel: +44 (0) 161 628 8406
Fax: +44 (0) 161 628 9811
MEYERTECH LIMITED
FUSION-AUDIT-ZVK

FUSION-AUDIT-ZVK Installation Guide Issue 01 Page 16 of 21
FUSION-AUDIT-ZVK
Meyertech Limited is a member of the CCTV User Group.
Warranty
Please refer to Meyertech Limited ‘Terms & Conditions of Sale of Goods & Services’ for interpretation.
1. If the Buyer establishes to the Seller's reasonable satisfaction that there is a defect in the materials or
workmanship of the Goods manufactured, then the Seller shall at its option, at its sole discretion and within a
reasonable time,
a. arrange for the repair or making good such defect or failure in such Goods free of charge to the Buyer
(including all costs of transportation of any Goods or materials to and from the Buyer for that
purpose),
b. replace such Goods with Goods which are in all respects in accordance with the Contract, or
subject, in every case, to the remaining provisions of this Condition 1 provided that the liability of the Seller under this
Condition 1 shall in no event exceed the purchase price of such Goods and performance of anyone of the above
options shall constitute an entire discharge of the Seller's liability under this warranty.
2. Condition 1 shall not apply unless the Buyer:
a. notifies the Seller in writing of the alleged defect within 12 (twelve) months from delivery or such other
period or periods as may be agreed in writing between the Seller and the Buyer, and
b. allows the Seller a reasonable opportunity to inspect the relevant Goods.
3. For the avoidance of doubt, the Seller shall be under no liability under the warranty in Condition 1 above:
a. where such defects arise from any drawing, design or specification supplied by the Buyer; or
b. where such defects arise from fair wear and tear, wilful damage, or negligence of a party other than
the Seller (or its employees or authorised personnel), abnormal working conditions, failure to follow
the Seller's instructions (whether oral or in writing), misuse or alteration or repair of the Goods without
the Seller's approval; or
c. where such defects arise in parts, materials or equipment which have not been manufactured or
designed by the Seller but have been purchased at the Buyer's request by the Seller from the Buyer's
designer and manufacturer or from some other third party (the “Third Party Supplier”).
d. if the total price of the Goods has not been paid by the due date for payment
e. in respect of any type of defect, damage or wear specifically excluded by the Seller by notice in
writing: or
f. if the Buyer makes any further use of the Goods after giving notice in accordance with Clause 1
4. Any repaired or replaced Goods shall be redelivered to the Buyer free of charge to the original point of
delivery but otherwise in accordance with and subject to these Conditions.
5. Alternatively to Condition 1 the Seller shall be entitled at its absolute discretion on return of the defective
Goods to the Seller (at the Seller's request) to refund the price of the defective Goods in the event that such
price shall already have been paid by the Buyer to the Seller, or, if such price has not been paid, to relieve the
MEYERTECH LIMITED

FUSION-AUDIT-ZVK Installation Guide Issue 01 Page 17 of 21
Buyer of all obligation to pay the sum by the issue of a credit note in favour of the Buyer in the amount of such
price.
6. In respect of all Goods supplied to the Seller by a Third Party Supplier the Seller will on request pass on to the
Buyer (in so far as reasonably possible) the benefit of any warranty given to the Seller by such Third Party
Supplier and will (on request) supply to the Buyer details of the terms and conditions of such warranty and
copies of any relevant product information sheets, technical data sheets or product leaflets issued by such
Third Party Supplier and the Buyer shall be solely responsible to the entire exclusion of the Seller for
complying with the same.
7. For the purposes of Condition 1 references to Goods shall be deemed to exclude software.
8. The Buyer acknowledges that software in general is not error-free and agrees that the existence of such
errors in the Software Programs shall not constitute a breach of this Contract.
9. In the event that the Buyer discovers a material error which results in the Programmed Products not
performing substantially in accordance with the Functional Specification, or the Licensed Programs not
performing substantially in accordance with the relevant Program Documentation and notifies the Seller of the
error within 90 days from the date of the Seller making available the respective software to the Buyer (the
`warranty period")the Seller shall at its sole option either refund the price which the Buyer has paid to the
Seller (or if such price has not been paid, relieve the Buyer of all obligations to pay the sum) in respect of the
respective software or use all reasonable endeavours to correct by patch or new release (at its option) that
part of the software which does not so comply provided that such non-compliance has not been caused by
any modification, variation or addition to the software not performed by the Seller or caused by its incorrect
use, abuse or corruption of the software by use of the software with other software or on equipment with
which it is incompatible,
10. To the extent permitted by English law, the Seller disclaims all other warranties, with respect to the software
which it provides pursuant to the Contract, either express or implied, including but not limited to any implied
warranties of satisfactory quality or fitness for any particular purpose.
11. The Buyer is solely responsible for various scanning the software that it receives from the Seller pursuant to
the Contract.
12. The Seller warrants that it will use reasonable skill and care in providing the Services to the buyer
MEYERTECH LIMITED
FUSION-AUDIT-ZVK

FUSION-AUDIT-ZVK Installation Guide Issue 01 Page 18 of 21
Minimum System Requirements
The minimum recommended PC hardware to run FUSION-AUDIT-ZVK is dictated by the Operating System you are running.
i.e. that recommended by Microsoft for running a particular Operating System. FUSION-AUDIT-ZVK also requires:
1. One free Serial RS232 port
2. SVGA 1024 x 768 colour monitor
3. Fusion Audit
Recommended operating systems for FUSION-AUDIT-ZVK are:
1. Microsoft Windows 2000
2. Microsoft Windows XP (default new installation unless specified)
MEYERTECH LIMITED
FUSION-AUDIT-ZVK

FUSION-AUDIT-ZVK Installation Guide Issue 01 Page 19 of 21
Appendix A
FUSION AUDIT ZVK Recovery Procedure
If FUSION-AUDIT-ZVK fails to respond to user input the program or operating system might have crashed. The problem may
manifest itself in a number of ways EG a Windows error screen may appear advising the application is about to close, the
appearance of the egg-timer icon indicating the system is executing a command; but never completes it resulting in a ‘locked-
up’ appearance; ETC
Fault Logging and Reporting
In order for faults to be fixed in future releases of Windows and FUSION-AUDIT-ZVK it is important that all faults are logged
and reported to Meyertech.
When you experience a fault please note down as much information as you can about the status of the system when the fault
occurred IE:
• What operation, if any was being performed at the time the fault occurred?
• If there are any error messages on the screen please carefully note them down before clearing them.
• How did you rectify the fault EG reset the PC
General Recovery from a Fault
If a minor fault occurs recovery can normally be achieved by simply closing the FUSION-AUDIT-ZVK application and then
restarting the application. If the problem persists you may have to restart Windows by quitting FUSION-AUDIT-ZVK and
restarting Windows.
MEYERTECH LIMITED
FUSION-AUDIT-ZVK
Table of contents
Other ZoneVu Network Hardware manuals
Popular Network Hardware manuals by other brands

Provision ISR
Provision ISR NVR-16400 user manual

HP
HP 10:10 LAN Bridge MB Installation and reference guide

Digitus
Digitus DN-16121 manual

Intellitec
Intellitec 500A Installation & service manual

Nexcom
Nexcom NSA 5181 Quick reference guide

PaloAlto Networks
PaloAlto Networks ION 1200-C-NA/ROW quick start guide