zonzou S68A User manual

www.zonzousmart.com
zonzou Smart Riding
Helmet User Guide
www.zonzousmart.com
MODEL:S68A/S68B

Warning!
Please read the user guide
carefully before using the helmet

P01 Overview
EN
Scope of Use
If any discrepancies between actual products and
pictures in this manual, please refer to the actual
product.
This manual only provides a reference for how to use
the helmet.
Safety
Comfort
Precautions
Please do not use any helmet after impact. Please
replace it or stop using it. We offer discounts for exchange.
This helmet is suitable for cycling, skating, skateboarding,
electric bicycles, balance bikes and other non-motorized
sports. It is not suitable for motorcycles or motor vehicles.
The helmet has been tested and it is qualified to protect the
head and reduce possible damage caused by impacts. In
order to better protect the user, in addition to using the
helmet correctly during exercise should also use it in an
appropriate exercise environment and exercise methods.
The helmet is designed to be light and does not increase
the burden which will meet your long-hours exercise needs.
Fine design with multiple holes which is good for
ventilation, cool and comfortable. Using the soft and elastic
cushion lining, it will not pressure your head and feel more
comfortable when wearing it.
Warning!

P02 Methods of Wearing
EN
Buckle
Press

Warning！
How to use the buckle
In order to better protect users, please wear the
helmet correctly. Please do not use any helmet after
impact. Please replace it or stop using it.
Connect 2 buckles and lock it as the picture shows.
Buckle
Correct Wearing Methods
Right Wrong Wrong

How to adjust the strap and buckle
Warning！
Please make sure to buckle up before riding. The strap of the helmet
should be adjusted properly, not too tight nor too loose. Adjusting the
strap too loosely or wearing it incorrectly can easily cause the helmet
to slip off the head. It cannot protect the head properly when an
accident happens. It may cause injury or death.
There is a fan-shaped buckle device located on the strap and movable
up and down, one on each side. See picture (A) for how it moves. See
picture (B) for its position, it should be on the lower edge of the ear.
EN
The helmet will fall easily if the strap is too loose. It is not
comfortable if it is too tight. Please adjust the strap according to
your head shape.
Warning !
P03Methods of Wearing
How to move the buckle
(A) (B)
Helmet
Strap
Up and down pulling
strap adjustment
Fan-shaped
buckle
Correct wearing position
Fan-shaped
buckle

Adjusters with snaps or slide rails can be adjusted to a
comfortable angle according to your needs, and it is
disassembled for cleaning and maintenance. It is
replaceable if damaged.
Steps to adjust the angle of the adjustor:
※Before using the helmet, please make sure that the slide
rail and the slide groove are in the right positions.
In the process of using the adjuster, please be careful
not to get your hair caught in the adjusting knob.
How to adjust the angle of the adjuster
EN
P04 Methods of Wearing
Warning！
Stabilize the front with one
hand and adjust the adjuster
moderately with the other.
4
Size Adjustment System
Method of adjuster
If it is too tight, please
adjust it counterclockwise.
If it is too loose, please
adjust it clockwise.
How to adjust the adjuster

Adjust the angle through the three adjustment positions, and
re-select the position of the snap button or slide
button you want. At last buckle the adjuster with
the snap button or slide button seat.
EN
※Attach the adjuster
to the snap seat
before buckling,
make sure that
the position of
the buckle pins
on the left and
right adjusters are
the same.
How to remove the adjuster pad
Velcro
Adjuster
Inner pad on the adjuster
Before using the helmet, please make sure that
the adjustor pad has been pasted on the adjustor.
Severe impact or external force
squeezing can easily cause damage or deformation of the adjustor.
Warning!
Warning!
P05
Snap button or
sliding button
seat with three adjustment
positions.
Snap or slide fastener
(removable)
Adjuster with slide: to
adjust different angles
and positions in order to
achieve the most
comfortable position that
best suits your head
shape. It can be
disassembled for cleaning
and replacement.
Methods of Wearing
Adjuster

EN
※ Please do not block the helmet holes to maintain
ventilation and comfort, when assembling the lining.
※ In order to ensure the health, safety and comfort
of riding, please do not repeatedly use the same
lining for a long time, especially for damaged or
worn lining, which need to be replaced in time.
※ It is recommended that the lining be cleaned or
replaced periodically.
Warning!
P06 Helmet lining
6
How to use and replace the lining
Youyun'an smart helmets only have one set of lining combinations.
If you need other combinations, feel free to choose the one suits
you best. Please purchase it separately (Please make sure the lining
combination is correct for your helmet model)
※The lining is glued and
fixed with the velcro on
the helmet body which is
easy to disassemble and
assemble.
Helmet Strap
Inner pad
on the adjuster
Top Lining
Helmet Strap

EN
A
Self-check Mode
P07 Indicator function
battery indicator
Magnetic
Charging Port
control button
※Press and hold the main switch button for 3 seconds
to turn it on with a beep.
※ When the battery indicator shows the battery
normally, all the colored lights next to the rear lights
(left and right sides) will light up one by one, and the
self-test is completed after two beeps. (The battery
indicator will automatically turn off after the self-check
is completed. Press the button to show battery usage).
※The charging indicators in red will light up from left to
right.
※ Then the light of the charging indicator will display
according to the current actual power. (One light on
means that the current battery is 20% when it is fully
charged, two lights on means 40%, and so on.)

EN
P08 Indicator function
B
Riding Mode
It takes one second after the beep to do
reverse turning.
※ It takes one second after the beep to do
reverse turning.
※ The system will enter the self-check mode
(indicators light up one by one).
※ After the self-check is completed it will enter
constant lighting mode after two beeps.
※ At this time, press the main switch button to
enter other riding mode selection.
※ Main switch button: Press and hold for 3
seconds with a beep and turn on the helmet
(press and hold for 3 seconds to turn off when it
is on)
※ Constant light mode: is the default model after
power on.
※ Riding modes include: constant light mode,
fast flash mode, slow flash mode, double flash
mode, etc.

C
Left Turn Mode
※ Reminder: Swing your head 15~30 degrees is the best way
when turning.
※ Rear lights: Yellow light at the left flashes and red light at
the right is on constantly.
※ After entering the left turning model about 8 seconds, it
will return to the initial state after 2 beeps.
※ Swing your head to the left and return back to the central.
It enters the left turning model after one beep.
EN
※ After the self-inspection mode is completed, the left and
right red lights will flash slowly (constant light mode). At
this time, press the button to select the double flash mode
(left and right yellow lights flash at the same time).
Press again to return to the constant light mode, repeat in
this way. (S68A only)
※ After the self-check mode is completed, the white light
constantly flashes. At this time, press the button to select
the white light to flash slowly (slow flash mode), and
press the button again to select the white light to flash
quickly (fast flash mode), and press again to return to the
white light to turn on constantly, repeat in this way.
(S68B only).
P09 Indicator function

G
Charging Mode
EN
P10 Indicator function
E
Braking Mode
※ It will trigger the sensor and enter the braking mode when
speed changes suddenly (braking).
※Warning light: After all the red lights are on for 2 seconds,
the red light flashes, and it returns to the constant light
mode after 8 seconds.
D
Right Turn Mode
※ Warning lights: Yellow light at the right flashes and red
light at the left is on constantly.
※ Swing your head to the right and return back to the
central. It enters the right turning model after one beep.
※After entering the right turning model about 8 seconds, it
will return to the initial state after 2 beeps.
※Reminder: Swing your head 15~30 degrees is the best way
when turning.
※ There are 2 charging modes: power-on and power-off
charging mode. The red indicator light shows dynamic
indication in the under-charged section, and it is steady in
the fully-charged section during charging. The first red light
from the left to the far right shows as a dynamic real-time

P11 Charging Mode
display when the battery is lower than 20% during charging.
The first red indicator light on the left is on steadily. The
second red light and lights to the far right will be on a
dynamic real-time display when charging over 20% but lower
than 40% during charging, and so on. The fifth red light will
be flashing when charging over 80% but lower than 100%.
Five indicator lights will be on at the same time when it is
fully charged. After turning off and charging, it will return to
the off state, and after turning on and charging, it will return
to the on state.
※ Need to open the rubber plug with the USB symbol when
charging (open the notch on the right side of the USB symbol
to see the Type-C charging port). Plug in the Type-C charging
cable, connect the 5V+/-0.25V, 500mA power supply and the
helmet will be automatically charged.
USB rubber plug USB charging port Plug in the USB power cord
※ The USB rubber plug needs to be replaced after charging.
After pressing the rubber plug, you need to use your fingers
EN

¤
Buzzer Tone
P12 Buzzer Tone
※ There will be a beep to remind you every time the button
completes an action.
※ Turn signal tone: To turn on turning light one beep, after 8
seconds two beeps indicate the completion of the turn and
turn off the turn signal.
※ Low battery (battery less than 10%) warning tone: four
beeps at a time, two times in a row. Reminding once every 5
minutes, it will power off after a total of three reminders, and
the first red battery indicator on the left flashes when low
battery.
※ Power on/off: the buzzer will beep once.
to slide and press from the right end to the left end of the
rubber plug slightly, so that the USB rubber plug can better
fit the shell, which can achieve better dust and waterproof
effects! (As shown below)
EN

¤
Product Parameter
The system will automatically shut down when the
helmet is not in use and kept still for 3 minutes.
Attention!
EN
Product name: Smart helmet
Product features: somatosensory control, intelligent turning
Product model: S68A/S68B
Product head girth: 550~590mm (M/L)
Product size: 286 x 214.5 x 141mm
Product weight: 370g(S68A); 350g(S68B)
Rated power (W): Max:1W
Rated working voltage (V): 3.5~4.25V
Battery specification: 3.7V, 650mA
Charging parameters: 5V+/-0.25V, 500mA
Average working current: about 80mA (various with
different working modes)
Continuous working time: around 10 hours
o
Applicable environment: temperature -20 to+ 50c,
humidity 0%~90%RH non-condensing
P13 Product parameter
Cleaning instructions
Attention!

¤
Limited Warranty Period
P14 Warranty
EN
※ Youyun'an guarantees that all products sold are free from
defects in materials and workmanship within one year from
the date of purchase, unless the product is otherwise
specified. If Youyun'an discovers that the product is defective,
Youyun'an may decide to replace the defective product at its
own discretion. Youyun'an is not responsible for any costs,
losses or damages incurred due to the loss or use of any
product, and Youyun'an explicitly denies all claims for indirect
and accidental damages.
Storage instructions
Please use neutral soap and water to clean the helmet if
you use solvents. If solvents, paint release agents, etc.
the helmet will be damaged easily, and even cannot be
used for protection in an accident
Helmets are easily damaged in an environment above
60 degrees Celsius. Dark transportation vehicles and
storage bags can easily exceed this temperature in hot
weather. After the helmet is heated, it will bubble up and
have an uneven surface which will make the helmet out
of shape. Please dispose or exchange the helmet timely
when it is damaged. t

P15 Warranty
This limited warranty does not cover normal wear and tear.
Youyunan does not guarantee the battery life used in its
products. Because the actual life of the battery will be
affected and changed by many factors, such as different
configuration and use of the product.
This limited warranty is subject to the following important
restrictions:
This limited warranty does not apply to any problems other
than product manufacturing and processing defects.
※ This warranty only applies to products purchased directly
from Youyun'an or Youyun'an authorized distributors. This
limited warranty only applies to the original purchaser of the
product, and does not include users who have obtained the
product through resale, lease or transfer.
If you try to use products other than Youyunan products and
services for repairs, or use any third-party products (such as
sealants, cameras or helmet liners) in combination with this
product, this limited warranty will be void.
Through investigation, if Youyunan finds that you modify,
change or alter the product in any way, this limited warranty
will be void.
Please decide for yourself whether to use our products, you
will be fully responsible (youyunan does not bear) any loss,
liability or injury caused by the use of our products, including
life, personal injury, or loss/damage of computers and mobile
devices and all other property. Youyun'an does not guarantee
the battery life of the product or any related product features.
EN

Use warning
P16 Use warning
Any warranty included in the laws of any country, including
guarantees of marketability and suitability for specific
purposes, are all restricted by the limited warranty duration.
Some countries do not allow limited warranty, therefore
aforementioned limitations might not be applicable for you.In
addition to the limitations, the aforementioned limited
warranty will supersede all other warranties, guarantees,
agreements and similar obligations of the manufacturer or
seller.
This product is only suitable for non-electric leisure pedal
riding. No helmet can prevent all injuries. Serious injury or
death may occur while riding a bicycle. Youyunan does not
admit that this helmet will eliminate all possibility of injury.
Youyun'an smart lights are designed to assist rather than
replace normal bicycle front lights and rear lights.
Youyun'an smart lights are designed as an auxiliary design
and not as a substitute for gesture signals. We cannot
guarantee that every car driver or person will recognize or
notice brake or turn signals. The indicator light can help you,
The laws of some countries and cities/regions require cyclists
to keep front and back light at all times. Please make sure
you understand and abide by local laws and regulations.
EN

P17 Use warning
EN
but there is no guarantee that accidents or collisions will not
occur.
The helmet is not designed for use in motor vehicles. It is
only suitable for sports scenes where the helmet is certified
and suitable. When using it, check whether the helmet is
damaged or whether it is worn correctly. This helmet is not
suitable for children.

EN
www.zonzousmart.com
Shenzhen Youyunan Intelligent Technology Co., Ltd.
Add : ROOM 706,51 PINGXIN NORTH ROAD,SHANGMUGU COMMUNITY,PINGHU STREET,
LONGGANG DISTRICT ,SHENZHEN,CHINA
Need more help? Send an email to
[e-mail]
and we are happyto help you!
Website
P18 Company Information