Zoomnet Bgate-GT10-I User manual

Bgate-GT10-I
User Manual

Bgate-GT10-I
Zoomnet Confidential Proprietary @ 2013 Zoomnet Corporation. All rights reserved I
LEGAL INFORMATION
By accepting this certain document of Zoomnet CORPORATION you agree to the following
terms. If you do not agree to the following terms, please notice that you are not allowed using
this document.
Copyright © 2013 Zoomnet CORPORATION. Any rights not expressly granted herein are
reserved. This document contains proprietary information of Zoomnet CORPORATION. Any
reproduction, transfer, distribution, use or disclosure of this document or any portion of this
document, in any form by any means, without the prior written consent of Zoomnet
CORPORATION is prohibited.
is registered trademark of Zoomnet CORPORATION. Zoomnet’s company name, logo
and product names referenced herein are either trademarks or registered trademarks of
Zoomnet CORPORATION. Other product and company names mentioned herein may be
the trademarks or trade names of their respective owners. Without the prior written consent
of Zoomnet CORPORATION or the third party owner thereof, anyone’s access to this
document should not be construed as granting, by implication, estopped or otherwise, any
license or right to use any marks appearing in the document.
The design of this product complies with requirements of environmental protection and
personal security. This product shall be stored, used or discarded in accordance with
product manual, relevant contract or laws and regulations in relevant country (countries).
This document is provided “as is” and “as available”. Information contained in this document
is subject to continuous update without further notice due to improvement and update of
Zoomnet CORPORATION’s products and technologies.
History Version
Version Author Time Remarks

Bgate-GT10-I
Zoomnet Confidential Proprietary @ 2013 Zoomnet Corporation. All rights reserved II
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
- Reorient the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into and outlet on a circuit different from that to which the receiver
is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Any special accessories needed for compliance must be specified in the instruction manual.
You are cautioned that changes or modifications not expressly approved by the party responsible
for compliance could void your authority to operate the equipment.
The minimum distance between this equipment and user should be 40 cm when the equipment
operates.

Bgate-GT10-I
Zoomnet Confidential Proprietary @ 2013 Zoomnet Corporation. All rights reserved III
Preface
This manual mainly introduces how to configure the Bgate-GT10-I to users when they install
AP device. It’s suggested to read this guide carefully before install the Bgate-GT10-I.
This part includes the follow contents:
 Content introduction
 Readers
 Conventions
 Content introduction
This document introduces WEB configuration, CLI confuguration and WEB upgrade. It is
divided into six chapters.
 Chapter 1 Product Introduction
 Chapter 2 WEB Configuration and Management
 Chapter 3 CLI Configuration
 Chapter 4 Change AP Working Mode
 Chapter 5 Common Operation in Fat AP Mode
 Chapter 6 Upgrade
 Readers
This document is for readers as followss:
 FAE and technical support
 Network manager
 Convention of symbols in this manual
Format
Definition
<> Characters in <> means this is a button, such as < OK>
[ ] Characters in [ ] means this is a window, menu or a datasheet, like popup
a [new user] window.
/ Multilevel menu will use “/” to separate, such as [File/New/Folder], that
means choose folder in the multilevel menu File/ New
This document adopts the following symbols to inform readers of special attention when they
are operating the device. Notes and tips in the body of manual will be shown in Times New
Roman fonts, and separated from surround contents with a horizontal line as followss:

Bgate-GT10-I
Zoomnet Confidential Proprietary @ 2013 Zoomnet Corporation. All rights reserved IV


TIP:
Means a complementary description
Caution：
：：
：
Means reader be careful. Improper operation may cause data loss or damage to equipment.
Professional installation:
The device cannot be sold retail, to the general public or by mail order. It must be sold to dealers. It
is installed by licensed professionals with special training according to Installation instruction
provided by dealer or grantee.

Bgate-GT10-I
Zoomnet Confidential Proprietary @ 2013 Zoomnet Corporation. All rights reserved V
Contents
1 PRODUCT INTRODUCTION ....................................................................................... 1
2 WEB CONFIGURATION AND MANAGEMENT.......................................................... 2
2.1 NETWORK SETTINGS ......................................................................................... 2
2.1.1 WAN INTERFACE NETWORK SETTINGS ................................................... 2
2.1.2 WIRELESS NETWORK SETTINGS .............................................................. 3
2.2 LOG ON ................................................................................................................. 4
2.3 SYSTEM STATUS ................................................................................................. 4
2.4 WIRELESS SETTINGS ......................................................................................... 4
2.4.1 WIRELESS STATUS ..................................................................................... 4
2.4.2 VAP SETTINGS ............................................................................................. 4
2.4.3 ADVANCED SETTINGS ................................................................................ 5
2.4.4 MULTI SSID-VLAN BINDING ........................................................................ 5
2.5 TCP/IP SETTINGS ................................................................................................ 6
2.5.1 LAN STATUS ................................................................................................. 6
2.5.2 LAN SETTING ................................................................................................ 6
2.6 DEVICE MANAGEMENT ...................................................................................... 6
2.6.1 TIME SETTING .............................................................................................. 6
2.6.2 SYSTEM LOG ................................................................................................ 6
2.6.3 FIRMWARE UPGRADE ................................................................................. 6
2.6.4 CONFIGURATION BACKUP AND RESTORE .............................................. 6
2.6.5 USER MANAGEMENT .................................................................................. 6
3 CLI CONFIGURATION................................................................................................. 6
3.1 ENTERING CLI...................................................................................................... 7
3.1.1 TELNET BY DOS INTERFACE ..................................................................... 7

Bgate-GT10-I
Zoomnet Confidential Proprietary @ 2013 Zoomnet Corporation. All rights reserved VI
3.1.2 LOGIN THROUGH RS 232 CONSOLE PORT .............................................. 7
3.1.3 LOGIN BY SECURECRT TOOL .................................................................... 8
3.2 CLI COMMANDS ................................................................................................... 9
3.2.1 IFCONFIG ...................................................................................................... 9
3.2.2 IWCONFIG ................................................................................................... 10
3.2.3 IWPRIV ......................................................................................................... 12
3.2.4 WLANCONFIG ............................................................................................. 14
3.2.5 IWLIST.......................................................................................................... 15
3.2.6 SYNTHESIS INSTANCE .............................................................................. 16
4 CHANGE AP WORKING MODE................................................................................ 16
4.1 OPERATING THROUGH WEB UI ...................................................................... 16
4.2 OPERATING THROUGH SERIAL PORT ........................................................... 16
5 COMMON OPERATION IN FAT AP MODE.............................................................. 17
5.1 CHECK AP INFORMATION ................................................................................ 17
5.2 CREATE VAP ...................................................................................................... 17
5.3 MODIFY WIRELESS PARAMETERS ................................................................. 18
5.4 CHECK AND MODIFY PARAMETERS .............................................................. 18
5.5 CHECK AND MODIFY VAP CHANNEL .............................................................. 19
5.6 CHECK AND MODIFY OUTPUT POWER .......................................................... 19
5.7 SAVE CONFIGURATION .................................................................................... 19
5.8 BACKUP CONFIGURATION TO LOCAL PC ..................................................... 19
5.9 FACTORY DEFAULT .......................................................................................... 20
5.10 SOFTWARE MIRROR ......................................................................................... 20
5.10.1 MIRRORING DESCRIPTION ..................................................................... 20
6 UPGRADE .................................................................................................................. 20
6.1 CONNECT AP CORRECTLY .............................................................................. 20

Bgate-GT10-I
Zoomnet Confidential Proprietary @ 2013 Zoomnet Corporation. All rights reserved VII
6.2 SET IP FOR COMPUTER ................................................................................... 21
6.3 LOGIN AP ............................................................................................................ 21
6.4 FIRMWARE UPGRADE ...................................................................................... 21
6.5 CHECKING .......................................................................................................... 22

Bgate-GT10-I
Zoomnet Confidential Proprietary @ 2013 Zoomnet Corporation. All rights reserved VIII
Contents of Figure
Figure 1-1 Product Appearance ........................................................................................................ 1
Figure 2-1 ping default IP of AP ........................................................................................................ 3
Figure 3-1 DOC interface .................................................................................................................. 7
Figure 3-2 Telnet management interface .......................................................................................... 7
Figure 3-3 Startup information of AP ................................................................................................. 8
Figure 3-4 Logining interface ............................................................................................................. 8
Figure 3-5 wlanconfig instance ........................................................................................................ 15
Figure 3-6 Synthesis Instance ......................................................................................................... 16
Figure 4-1 Setting AP mode through serial port .............................................................................. 17
Figure 5-1 Check AP version ........................................................................................................... 17
Figure 5-2 Check VAP mode ........................................................................................................... 18
Figure 5-3 Check VAP Channel ...................................................................................................... 19
Figure 5-4 Check Output Power of VAP .......................................................................................... 19
Figure 6-1 Connect AP .................................................................................................................... 21
Figure 6-2 PoE port of AP ............................................................................................................... 21
Contents of Table
Table 2-1 Default Configuration of AP ............................................................................................... 4
Table 3-1 Default Configuration of AP ............................................................................................... 6
Table 3-2 Necessary software tool .................................................................................................... 7
Table 3-3 Hyper Terminal parameters .............................................................................................. 8
Table 3-4 CLI Commands Overview List ........................................................................................... 9

Bgate-GT10-I
Zoomnet Confidential Proprietary @ 2013 Zoomnet Corporation. All rights reserved 1
1 Product Introduction
Figure 1-1 Product Appearance
Bgate-GT10-I, the product which zoomnet company launched is an 11n access point with
high power and double frequency. Compared with traditional 54Mbps 11G and 108Mbps
Super G products, Bgate-GT10-I provides a rate of 300Mbps. With such high bandwidth, it
highly enhances data transmission’s effectiveness and reduces network delay in voice and
video processing, network game playing, and video-on-line selecting.
Double frequency design satisfies the application needs of 2.4GHz and 5.8GHz. With a gain
planar antenna, Bgate-GT10-I highly enhances wireless reception and emission capacity,
ensuring wireless signal’s stability. The adoption of WPA/WPA2 and WEP security
mechanism provides an overall safeguard for wireless network. Bgate-GT10-I is a newly
developed comprehensive access point, which can be used to receive WiFi signal, cover
wireless signal, and amplify signal. Meanwhile it can also work together with AC to realize a
centralized management.
Hardware Specification
Items
Description
WLAN IEEE802.11a/b/g/n(2*2:2)；Speed up to 300Mbit/s
Interface
10/100/1000M Ethernet Interface；Console Interface （for
manufacture use only）；2 x N Female Interface for 5GHz
band；GND Earth Terminal；
2.4GHz band Directional
integral MIMO antenna Antenna Gain: 13.5dBi
5GHz band Directional
dedicated MIMO antenna Model: TDJ-5158GAx2

Bgate-GT10-I
Zoomnet Confidential Proprietary @ 2013 Zoomnet Corporation. All rights reserved 2
Items
Description
Indicator One Power Indicator
One WiFi Indicator
Power Supply POE+（Accords with 802.3at standard）
Power consumption ＜26W
Dimension 300mm * 226mm * 144.5mm
Work Temperature -40℃ ～ +55℃
Relative Humidity 0% ～ 100%
Weight ≤5Kg
Protection Grade IP67
Accessories One mounting rack
Wind-resisting Strength ＞90MPH
2 WEB Configuration and Management
2.1 Network Settings
You will need to install a wired or wireless network adapteradapter on your computer, and
connect it to the AP’s Ethernet port by exterior concentrator or switcher if you use wired
network adapter. If you use wireless network adapter, the connection of Ethernet port can be
skiped. Below operation steps are based on Windows XP, and the UI may be different if you
use some other OS.
2.1.1WAN interface network settings
Caution：
：：
：
AP device can work in two network environments. One is working as a NE independently with
WAN IP of 192.168.0.1 and subnet mark 255.255.255.0, and the other is controlled by AC, obtaining
IP address and subnet mark from AC.
After AP device obtains IP address, you should follow the below steps to manually set IP
address of PC, which is used to configurate and manage AP device
Step1. Click [Start > Settings > Network Connections], and access the network settings
UI. (Note: switch the menu to the classic view if you fail to find the settings option.)

Bgate-GT10-I
Zoomnet Confidential Proprietary @ 2013 Zoomnet Corporation. All rights reserved 3
Step2. Choose the internet connection that matches your wireless network adapter, right
click its icon, and choose properties.
Step3. Double click Internet Protocol (TCP/IP) option and the Internet Protocol (TCP/IP)
properties dialogue will be displayed.
Step4. Check the Use the following IP address option, and input IP address for PC. Note
that subnet segment of IP address should be the same as AP’s.
Step5. Set the subnet mask and click <OK>to finish the manual setting.
Step6. Ping the AP’s IP address. Once the internet connection is successfully established,
the below interface will display.
Figure 2-1 ping default IP of AP
2.1.2Wireless network settings
Caution:
This function is only used in the environment where AP is controlled by AC,otherwise STA can not
connect to AP and login WEB management page.
If you don’t want to use STA to manage AP, you can skip this chapter. We also suggest you not to
use STA to manage AP.
Please follow the steps below to connect wireless network (AC controlls AP).
Step1. Click [Start /Settings/Network Connections] and access the network connections
UI.
Step2. Right click the wireless network connections icon and choose <Properties>.
Step3. Double click the Internet Protocol (TCP/IP) option in the Properties interface, and
Internet Protocol (TCP/IP) Properties dialogue will pop up.
Step4. If the access controller is activated, the AP’s IP address can be assigned by AC
remotelythrough DHCP. You may check Automatic gain IP address to gain the IP address
assigned by DHCP Server.

Bgate-GT10-I
Zoomnet Confidential Proprietary @ 2013 Zoomnet Corporation. All rights reserved 4
Step5. Click the icon of wireless network adapter on the taskbar
Step6. Click the network connection status to Check the available wireless connections.
Step7. On the page of wireless connection, find out the SSID (take vap0 as example) of the
AP which you want to connect to, then choose it and click the icon <connect> on the lower
right corner.
Step8. If the wireless network adapter is connected to the device successfully, the reminding
information Connected will be displayed on the right corner of the network connection icon.
2.2 Log on
Table 2-1 Default Configuration of AP
Iterms
Description
IP address Base on the network environment, it may be https://192.168.0.1 or the
IP address which assigned by AC/DHCP SERVER
Username admin
Password password
AP provides a web page configuration interface for users, so you can access to the AP by
browsers.
1. Open a browser and input the AP’s IP addresses like “https:// 192.168.0.1”.
2. Input your username and password in the login UI. The default username/password
is“admin” and “password”.
2.3 System Status
There are three submenus in system status UI, including system information, LAN
congiguration and others
After login, it automatically access to system information page.Page of system information
displays system status, LAN configuration, wireless network adapter status and others.
2.4 Wireless Settings
Wireless settings page displays wireless status, base settings, VAP settings, advanced
settings and multi SSID-VLAN binding.
2.4.1Wireless Status
Click [Wireless Settings/ Wireless Status], access to page of Wireless Status.
2.4.2VAP settings
Click [wireless settings/ VAP settings] to access the UI.
1）Status: Check it to activate the virtual AP

Bgate-GT10-I
Zoomnet Confidential Proprietary @ 2013 Zoomnet Corporation. All rights reserved 5
2）Broadcast SSID: Check it to broadcast the SSID, otherwise hide the SSID
3）SSID: Display the network name
4）WMM: Enable or disable WMM control
5）Security: Click <Edit> button to choose authentication method, encryption algorithm and
secret key.
6）APPLY: After finish configuration, you need to click <APPLY> button to put the new
configuration into practice.
2.4.3Advanced settings
Click [wireless settings/ advanced settings] to access the UI.
1）Mode: 2.4G network could select 11B, 11G, 11NGHT20, 11NGHT40PLUS and
11NGHT40MINUS mode. 5.8G network could select 11A, 11NAH T20, 11NAHT40PLUS,
11NAHT40MINUS mode.
2）Channel: 2.4G frequency band can choose 1~11 channels, 5.8G frequency band can
choose 149~165 channels. Default selection is Atuo.
3）Speed: It can set as Auto or MCS0~MCS15, default selection is Auto.
4）MTU: Set the maximum fragmentation length. When data package is larger than this value,
it will be fragmented. Its unit is byte, range is 256~2346, and the default value is 2346.
5）RTS Threshold: Its unit is byte, range is 0~2347, 0 means disable this threshold and the
default value is 2346. When data frame is larger than this value, the RTS/CTS protection
mechanism will be enabled.
6）Ack timeout control: Its unit is μs, range is 0~256, and the default value is 64.
7）Beacon Interval: Its unit is TU, range is 100~1000, and the default value is 100.
8）Packet aggregation: Enable this function and MAPDU mechanism will be activated.
9）Short GI: By activating Short GI, data volume can be increased.
10）Wireless user isolation: When enable this item it will prevent wireless users
communicate with each other.
11）Txpower: Set Txpower for AP channel.
12）RS IP address: Fill in the IP address of RS server
13）AS IP address: Fill in the IP address of AS server
2.4.4Multi SSID-VLAN Binding
Click [wireless settings/ Multi SSID-VLAN binding] to access the UI and set its
parameters.

Bgate-GT10-I
Zoomnet Confidential Proprietary @ 2013 Zoomnet Corporation. All rights reserved 6
2.5 TCP/IP settings
In this chapter, it mainly introduces wired setting for WAN port (local LAN port), including
LAN status and LAN setting two submenus.
2.5.1LAN Status
Click [TCP/IP settings / LAN status] to access the UI.
2.5.2LAN Setting
Click [TCP/IP settings/ LAN status] to access the UI. Choose AP working mode as fat AP
or fit AP in the UI.
2.6 Device Management
In this page, it includes time settings, system Log, firmware upgrade, configuration backup
/restore, and user management.
2.6.1Time Setting
Click [Device management/ Time settings] to access the UI.
2.6.2System Log
Click [Device management/ system Log] to access the system log UI.
2.6.3Firmware Upgrade
Click [Device menagement / firmware upgrade] to access firmware upgrade UI.
Caution:
Don’t turn off the power when upgrading firmware, otherwise it may break down the system.
2.6.4Configuration Backup and Restore
Click [Device Menagement/ Configuration Backup and Restore] to access the UI.
2.6.5User Management
Open [Device Menagement/ User Management] to access the UI.
3 CLI Configuration
Obtain IP address for AP according to the network environment.
Table 3-1 Default Configuration of AP
Iterms Description

Bgate-GT10-I
Zoomnet Confidential Proprietary @ 2013 Zoomnet Corporation. All rights reserved 7
IP address Base on netwrok condition, it may be 192.168.0.1 or an IP address
that issued by AC/DHCP SERVER
Username root/admin(When login web page,username is admin)
Password Password or admin
Telnet Port 23
RS232 115200，n，8，1
Table 3-2 Necessary software tool
Tools Description
SecureCRT It is used to login device by console port or telnet.
HyperTerminal It is used to login device by console port.
Windows platform PC system, it is used to run the SecureCRT and HyperTerminal
In this chapter, the SecureCRT in Windows XP is used as an Instance.
3.1 Entering CLI
3.1.1Telnet by DOS interface
Click [Start/ run(R)…], type “cmd” into the run box and press <enter>, to access to DOS
interface.
Figure 3-1 DOC interface
Input the username and password, then access to telnet management UI.
Figure 3-2 Telnet management interface
3.1.2Login through RS 232 Console Port
Click [Start/Programs/Accessories/Communication/Hyper Terminal] to access to hyper
terminal UI

Bgate-GT10-I
Zoomnet Confidential Proprietary @ 2013 Zoomnet Corporation. All rights reserved 8
Create a new connect command, choose a suitable serial port, and follow the below table to
set the parameter.
Table 3-3 Hyper Terminal parameters
Iterms Parameters
Bits per second 115200
Data bits 8
Parity bit 0
Stop bit 1
DFC (Data flow control) Null
Type in username and password, and then click <OK> to access device UI.
Figure 3-3 Startup information of AP
3.1.3Login by SecureCRT Tool
SecureCRT is used to login device by console port or telnet. We take logining device by
console port as an example.
Run the SecureCRT tool, and input the correct username and password to access the UI
Username: root
Password: password
Figure 3-4 Logining interface

Bgate-GT10-I
Zoomnet Confidential Proprietary @ 2013 Zoomnet Corporation. All rights reserved 9
3.2 CLI Commands
Useful commands are shown in below
Table 3-4 CLI Commands Overview List
C
ommands
Function Description
ifconfig Set standard parameters for wired interface
iwconfig Set standard parameters for wireless interface
iwpriv Set standard parameters for private wireless interface
wlanconfig It is a utility tool that used to manage VAP instance.
iwlist Print the wireless parameters of output
get_ver.sh Check the firmware version
athstats Wireless statistics information
3.2.1ifconfig
ifconfig command is a tool used to manage and configure parameters for wired interface.
Online help is as followss:
BusyBox v1.15.0 (2011-09-01 17:32:37 CST) multi-call binary
Usage: ifconfig [-a] interface [address]
Configure a network interface
Options:
[[-]broadcast [ADDRESS]] [[-]pointopoint [ADDRESS]]
[netmask ADDRESS] [dstaddr ADDRESS]
[hw ether ADDRESS] [metric NN] [mtu NN]
[[-]trailers] [[-]arp] [[-]allmulti]
[multicast] [[-]promisc] [txqueuelen NN] [[-]dynamic]
[mem_start NN] [io_addr NN] [irq NN]

Bgate-GT10-I
Zoomnet Confidential Proprietary @ 2013 Zoomnet Corporation. All rights reserved 10
[up|down]
Parameters description:
interface: Port of network device.
down: Disable the specified port.
up: Enable the specified port.
-arp: Enable or disable a specified port using the ARP protocol, when put a negative sign
front “arp”, it means disable this option.
-allmuti: Enable or disable the indistinction mode of specified port, when put a negative sign
front “allmuti”, it means disable this option.
-promisc: Enable or disable the promiscuous mode of specified network device, when put a
negative sign front “promisc”, it means disable this option.
add<IP>: Set Ipv6 address for network device.
del<IP>: Delete the Ipv6 address of network device.
media<type>: Set type of media for network device
mem_start<memory address>: Set the initial address of primary memory for network
device.
metric< number>: A numeral add to the packetage When calculate its forwarded time.
mtu<value>: Set MTU for network device.
netmask< subnet mask>: Set subnet mask for network device.
tunnel< IP>: Set a tunnel IP address for Ipv4 device communicating with Ipv6 device.
-broadcast<IP>: Packets sent to the specified address are treated as broadcast packets.
-pointopoint< IP>: Derectly connect with the specified network device, this mode can keep
secret.
Instance:
# brctl addif br0 wifi0_wlan0 //Add the virtual AP(wifi0_wlan0) to bro port.
# ifconfig br0 192.168.0.1 netmask 255.255.255.0 // Set IP address and netmask
# ifconfig br0 192.168.0.1 // Set IP address
3.2.2iwconfig
iwconfig command is a set of instructions used to set up and run the WLAN interface
commands. The usages are similar to ifconfig, but they are only for 802.11 devices.
Online help is as followss:
# iwconfig --help
Usage: iwconfig [interface]
interface essid {NNN|any|on|off}
interface mode {managed|ad-hoc|master|...}

Bgate-GT10-I
Zoomnet Confidential Proprietary @ 2013 Zoomnet Corporation. All rights reserved 11
interface freq N.NNN[k|M|G]
interface channel N
interface bit {N[k|M|G]|auto|fixed}
interface rate {N[k|M|G]|auto|fixed}
interface enc {NNNN-NNNN|off}
interface key {NNNN-NNNN|off}
interface power {period N|timeout N|saving N|off}
interface nickname NNN
interface nwid {NN|on|off}
interface ap {N|off|auto}
interface txpower {NmW|NdBm|off|auto}
interface sens N
interface retry {limit N|lifetime N}
interface rts {N|auto|fixed|off}
interface frag {N|auto|fixed|off}
interface modulation {11g|11a|CCK|OFDMg|...}
interface commit
Check man pages for more details.
Parameter Description:
essid: Extended service set identifier SSID.
Instance: #iwconfig athN essid ZOOMNET_VAP0
Mode: Wireless mode, such as AP mode, AD-HOC mode and CLIENTmode.
Freq: The current frequency( It is a one-to-one correspondence between channel and
frequency).
Instance:
#iwconfig wifi0_wlan0 freq 5.2G
#iwconfig wifi0_wlan0 freq 40
Channel: Working channel
Instance:
#iwconfig wifi0_wlan0 channel 11
bit : Set the speed for wireless port, and its unit is bit.
rate: Set the speed for wireless port, and its value is percent value.
Instance:
#iwconfig wifi0_wlan0 rate 54M
enc: Set or manage WEP secret key. It can be set 4 keys on each radio module, you can
choose 1~4 to activate the key.