ZooZ ZEN05 User manual

WARRANTY
NEED SOME HELP?
[e-mail]
www.support.getzooz.com
OUTDOOR PLUG
ZEN05
www.getzooz.com
USER MANUAL
ŸZ-Wave™ on/off control of lights and small appliances
ŸIP65 rated for outdoor use
ŸEasy set-up and angled plug for better outlet fit
ŸS2 authenticated security and SmartStart
ŸSupports OTA firmware updates
ŸETL listed for compliance with North American safety
standards
ŸModel Number: ZEN05
ŸZ-Wave™ Signal Frequency: 908.42 MHz
ŸPower: 110 VAC, 60 Hz
ŸMaximum Load: 15 A, 150 W LED bulbs, 1000 W
incandescent, 1/3 hp motor
ŸRange: Up to 300 feet line of sight
ŸInstallation and Use: Indoor or outdoor
ŸIP Rating: 65
ŸDimensions: 2.25” x 3.25” x 1.5”
ŸCord Length: 6.5”
FEATURES
SPECIFICATIONS
CAUTION
This is an electrical device - please use caution when
installing and operating the Outdoor Plug. Remote
control of appliances may result in unintentional or
automated activation of power. Do NOT use this Z-
Wave device to control electric heaters or other ™
appliances which produce the risk of fire, burns, or
electrical shock when unattended.
INSTALLATION
Plug the Outdoor Plug into any standard grounded
110 V receptacle. Do NOT connect any devices to the
plug at this point. Click the Z-Wave™ button to see if
the LED indicator comes on and off. If the LED
indicator doesn’t light up at all, please try a different
receptacle. If it’s still off, please get in touch with our
support team: [e-mail]
ŸThis product should be installed indoors upon completion of
any building renovations.
ŸPrior to installation, the device should be stored in a dry, dust-
and-mold-proof place.
ŸDo not install the device in a place with direct sun exposure,
high temperature, or humidity.
ŸKeep away from chemicals, water, and dust.
ŸEnsure the device is never close to any heat source or open
flame to prevent fire.
ŸEnsure the device is connected to an electric power source that
does not exceed the maximum load power.
ŸNo part of the device may be replaced or repaired by the user.
WARNING
BEFORE YOU PLUG ANYTHING IN
Make sure the load you are about to connect
does NOT exceed 15 A in power. This Outdoor Plug
can hold up to 15 A in total.
Connecting heavy duty equipment to this
Outdoor Plug will DAMAGE the device and may
cause the connected appliance to malfunction.
Do NOT plug washers, dryers, refrigerators, or
motors over 1/3 hp to this Outdoor Plug.
Z-WAVE CONTROL™
1. ADD DEVICE to your hub
Initiate inclusion (pairing) in the app (or
web interface). Not sure how? Scan the QR
code below for instructions dedicated to your hub or
visit www.support.getzooz.com for more details.
If you’re using an S2 hub, it will ask you to enter the
DSK PIN or scan the QR code printed on the side of the
plug’s outlet to complete SmartStart inclusion.
While the hub is looking for new devices, click the Z-
Wave™ button 3 times as quickly as possible. The LED
indicator will start flashing blue to confirm inclusion
mode and turn green for 1 second once inclusion is
completed.
1. Bring the Outdoor Plug within direct range of your Z-
Wave™ gateway (hub).
2. Put the Z-Wave™ hub into exclusion mode (not sure
how to do that? [e-mail]).
3. Press and release the Z-Wave™ button 3 times
quickly.
4. Your hub will confirm exclusion and the Outdoor Plug
will disappear from your controller's device list.
EXCLUSION (REMOVING / UNPAIRING DEVICE)
FACTORY RESET
TROUBLESHOOTING
The Outdoor Plug won’t add to your hub? Try this:
1. Initiate EXCLUSION in your hub and click the Z-
Wave button 3 times as quickly as possible. Then ™
try adding it again aer it successfully excludes (this
works as a reset and can be tried even if the plug was
never connected to your hub in the past).
2. Click the Z-Wave™ button 4-5 times quickly when
adding it or try adding it in a non-secure mode.
3. Bring the Outdoor Plug closer to your hub, it may be
out of range.
4. Double-check if the device is powered.
5. Get more troubleshooting tips for your hub at
www.support.getzooz.com
When your network’s primary controller is missing or
otherwise inoperable, you may need to reset the device
to factory settings manually. In order to complete the
process, make sure the plug is powered, then click the
Z-Wave™ button twice and hold it the third time for
10 seconds. The LED indicator will flash green 3 times
to confirm a successful reset.
NOTE: All previously recorded activity and custom
settings will be erased from the device’s memory.
The Outdoor Plug supports Group 1 for Lifeline
communication and Group 2 with up to 5 devices for
basic on/off control. This device will send a Basic Set
command to Group 2 whenever it changes its on/off
status.
Please note that not all Z-Wave systems give users ™
access to direct association settings so if you’re note
sure where to find it, please get in touch with our
support and we’ll be happy to help.
2. PLUG the ZEN05 into a receptacle
PAGE 1 PAGE 2
This product can be included and operated in any Z-Wave ™
network with other Z-Wave certified devices from other ™
manufacturers and/or other applications. All non-battery
operated nodes within the network will act as repeaters
regardless of vendor to increase reliability of the network.
This product features the latest Security 2 (S2) framework to
remove smart home network hacking risks. This device is
equipped with a unique authentification code for trusted
wireless communication.
This is an ETL certified device. ETL, just like UL, is a Nationally
Recognized Testing Laboratory. The ETL mark is proof of
product compliance to North American safety standards.
S2
Z-WAVE™
BUTTON
QR / PIN CODE
Scan the code printed on the
device for SmartStart pairing
and NOT the QR codes below
which link to hub specific
instructions.
SmartThings Hubitat Home Assistant
SmartStart enabled products can be added into a Z-
Wave™ network by scanning the Z-Wave™ QR Code
present on the product with a controller providing
SmartStart inclusion.
Choose your hub and scan the QR code with your
phone’s camera. Then click on the link to access the
step-by-step pairing instructions.
ASSOCIATION
This product is covered under a 12-month limited
warranty and extended 5-year warranty once registered.
To read the full warranty policy, register your product, or
file a claim, please visit www.getzooz.com/warranty

Parameter 1: Decide how the LED indicator behaves
depending on the on/off status of the plug. The LED
indicator will flash twice to confirm a setting has been
changed.
Values: 0 – LED indicator is on when the plug is on, LED
indicator is off when the plug is off (default); 1 – LED
indicator is on when the plug is off, LED indicator is off
when the plug is on; 2 – LED indicator is always off.
Size: 1 byte dec
NOTE: Click the Z-Wave button 6 times quickly to ™
toggle between the values of this parameter manually
from the device.
Parameter 2: Use this parameter to set the auto turn-
off timer: the time aer which you want the Outdoor
Plug to automatically turn off once it has been turned
on. The number entered as value corresponds to the
number of minutes.
Values: 0 – timer disabled (default); 1-65535 (minutes).
Size: 4 byte dec
Parameter 4: Use this parameter to set the auto turn-
on timer: the time aer which you want the Outdoor
Plug to automatically turn on once it has been turned
off. The number entered as value corresponds to the
number of minutes.
Values: 0 – timer disabled (default); 1-65535 (minutes).
Size: 4 byte dec
Parameter 6: Choose the recovery state for your
Outdoor Plug if power outage occurs.
Values: 0 – Outdoor Plug automatically turns OFF once
power is restored (it ignores the status prior to power
outage); 1 – Outdoor Plug automatically turns ON once
power is restored (it ignores the status prior to the
power outage); 2 – Outdoor Plug remembers the status
prior to power outage and turns back to it (default).
Size: 1 byte dec
NOTE: Click the Z-Wave™ button 10 times quickly to
toggle between the values of this parameter manually
from the device.
Parameter 7: Set the brightness level of the LED
indicator.
Values: 0 – bright; 1 – medium; 2 – low (default).
Size: 1 byte dec
NOTE: Click the Z-Wave™ button 8 times quickly to
toggle between the values of this parameter manually
from the device.
Parameter 8:Choose if you want to use the physicalZ-
Wave™ button on the plug to turn the outlet on or
offmanually or if you want to disable this function. If
thisparameter is set to 0 (disabled), you will only be
able toturn the outlet on or off remotely using your Z-
Wave™hub.
Values:0 – manual control disabled; 1 – manual
controlenabled (default).
Size:1 byte dec
Choose your hub and scan the QR code with your phone’s
camera. Then click on the link to access the step-by-step
instructions on how to access advanced settings for the plug
on your Z-Wave system.™
Here is the list of command classes supported by this
device:
COMMAND_CLASS_ZWAVEPLUS_INFO_V2,
COMMAND_CLASS_SWITCH_BINARY_V2,
COMMAND_CLASS_CONFIGURATION_V4,
COMMAND_CLASS_ASSOCIATION_V3,
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V4
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V3,
COMMAND_CLASS_TRANSPORT_SERVICE_V2,
COMMAND_CLASS_VERSION_V2,
COMMAND_CLASS_MANUFACTURER_SPECIFIC,
COMMAND_CLASS_DEVICE_RESET_LOCALLY,
COMMAND_CLASS_INDICATOR_V3,
COMMAND_CLASS_POWERLEVEL,
COMMAND_CLASS_SECURITY_2,
COMMAND_CLASS_SUPERVISION,
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V5
ADVANCED SETTINGS
Please refer to your controller's user guide for advanced
programming instructions as they are different for every
soware. Not sure where to start? Go to
www.support.getzooz.com for detailed instructions
how to change the settings on SmartThings,
Hubitat, and more. Or just email us: [e-mail]
IN NO EVENT SHALL ZOOZ OR ITS SUBSIDIARIES AND
AFFILIATES BE LIABLE FOR ANY INDIRECT, INCIDENTAL,
PUNITIVE, SPECIAL, OR CONSEQUENTIAL DAMAGES, OR
DAMAGES FOR LOSS OF PROFITS, REVENUE, OR USE
INCURRED BY CUSTOMER OR ANY THIRD PARTY, WHE-
THER IN AN ACTION IN CONTRACT, OR OTHERWISE
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DA-
MAGES. ZOOZ'S LIABILITY AND CUSTOMER'S EXCLUSIVE
REMEDY FOR ANY CAUSE OF ACTION ARISING IN CON-
NECTION WITH THIS AGREEMENT OR THE SALE OR USE
OF THE PRODUCTS, WHETHER BASED ON
NEGLIGENCE, STRICT LIABILITY, BREACH OF WARRANTY,
BREACH OF AGREEMENT, OR EQUITABLE PRINCIPLES,
IS EXPRESSLY LIMITED TO, AT ZOOZ'S OPTION,
REPLACEMENT OF, OR REPAYMENT OF THE PURCHASE
PRICE FOR THAT POR-TION OF PRODUCTS WITH
RESPECT TO WHICH DA-MAGES ARE CLAIMED. ALL
CLAIMS OF ANY KIND ARISING IN CONNECTION WITH
THIS AGREEMENT OR THE SALE OR USE OF PRODUCTS
SHALL BE DEEMED WAIVED UNLESS MADE IN WRITING
WITHIN THIRTY (30) DAYS FROM ZOOZ'S DELIVERY, OR
THE DATE FIXED FOR DELI-VERY IN THE EVENT OF
NONDELIVERY.
FCC NOTE
THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY
RADIO OR TV INTERFERENCE CAUSED BY
UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT.
SUCH MODIFICATIONS COULD VOID THE USER’S
AUTHORITY TO OPERATE THE EQUIPMENT. STORE
INDOORS WHEN NOT IN USE. SUITABLE FOR DRY
LOCATIONS ONLY. DO NOT IMMERSE IN WATER. NOT
FOR USE WHERE DIRECTLY EXPOSED TO WATER.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following conditions:
1. This device may not cause harmful interference,
2. This device must accept any interference received,
including interference that may cause undesired
operation.
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a residential
installation.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used
according to instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will
not occur in any given installation.
If this equipment causes harmful interference to radio
or television reception, the user may try to correct the
interference by taking one or more of the following
measures:
- Reorient or relocate receiving antenna
- Increase the separation between equipment and
receiver
- Connect equipment into a separate outlet or circuit
from receiver
- Consult the dealer or an experienced radio/TV
technician for additional assistance
All brand names displayed are trademarks of their
respective holders.
© Zooz 2022
PAGE 4PAGE 3
Questions?
[e-mail]
SmartThings Hubitat Home Assistant