ZooZ 800 Series User manual

800 Z-WAVE STICK
ZST39
USER MANUAL
www.getzooz.com
FEATURES
ŸZ-Wave Plus Static USB Controller
ŸLatest S2 security protocol for a truly
private network
Ÿ800 Series Long Range Z-Wave for fast,
low-power direct communication
ŸExtended range up to a mile in open
space when using Long Range
ŸLED indicator for troubleshooting
ŸNo drivers needed: works out of the box
on Windows, Linux, and MAC OS
SPECIFICATIONS
ŸModel Number: ZST39
ŸZ-Wave Frequency: 908.42 MHz
ŸPower: 4.75-5.25 VDC
ŸSDK: 7.18.01
ŸOperating Temperature: 14-104° F
ŸOperating Humidity: Up to 85%
ŸInstallation and Use: Indoor only
ŸDimensions: 2" x 0.8" x 0.3"
SET-UP
Use this S2 800 Series Z-Wave USB Stick as
a Z-Wave radio for your DIY smart home
system. Simply connect it to a USB port on
your PC, laptop, or Raspberry Pi and match
it with home automation soware (host
soware) of your choice to enjoy a fully
secure, private Z-Wave Plus mesh network.
If the soware supports Z-Wave Long
Range, enable direct communication
between your devices and the controller for
supreme range up to 1 mile and a larger
network size up to 4000 nodes.
Questions? [e-mail]
WINDOWS SET-UP
Windows 2000, XP, Vista, 7, 8 (32 / 64 bit)
The device will display in Device Manager
under Ports. You can access it through the
Windows CreateFile API using “//.//COMxxx”
where xxx stands for the COM port number
assigned by Windows.
UZB.INF and UZB.CAT are listed in the Z-
Wave SDK which uses the standard
usbser.sys or usbser64.sys Windows driver.
LINUX SET-UP
Linux
The device will display as “/dev/ttyUSB0”,
you can discover it with the "dmesg | grep
tty" command.
MAC OS SET-UP
MAC OS
The device will display as
“/dev/cu.usbmodem” under Apple: System
preferences: Network.
SerialAPI Mode:
Once the S2 stick is plugged into the USB
port of the host computer, it automatically
enrolls in the SerialAPI mode and remains
active (awake), always listening for
commands sent from the host so-ware
and relaying them to the Z-Wave devices in
the network. It acts as a Z-Wave signal
adapter for your smart home system,
translating any Z-Wave reports and
notifications sent by devices in your
network to your smart home interface.
Scan to register your
product for extended
warranty, priority
customer service, and
more perks.
www.getzooz.com/register

FACTORY RESET
The 800 Series Stick can only be reset by the
host soware while it’s in SerialAPI mode.
The device is reset once an appropriate
command from the host soware is sent to
reset the Z-Wave network.
There is no way to manually reset the S2
stick if it’s not controlled by host soware.
WARNINGWARNING
ŸThis product should be installed indoors
upon completion of any building
renovations.
ŸDo not install the S2 Stick in a place with
direct sun exposure, high temperature, or
humidity.
ŸKeep away from chemicals, water, and
dust.
ŸEnsure the device is never close to any
heat source or open flame to prevent fire.
ŸEnsure the device is connected to an
electric power source that does not
exceed the maximum load power.
ŸNo part of the device may be replaced or
repaired by the user.
This product is covered under a standard 12-
month warranty and an extended 5-year
limited warranty once registered. To read the
full warranty policy or file a warranty claim,
please go to:
www.getzooz.com/warranty
FCC NOTE
THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY
RA D I O O R T V I N T E R F E R E N C E C A U S E D BY
UNAUTHORIZED MODIFICAT I O N S TO T H I S
EQUIPMENT. SUCH MODIFICATIONS COULD VOID
THE USE R’ S AUT HO RI TY TO OPERATE THE
EQUIPMENT. STORE INDOORS WHEN NOT IN USE.
SUITABLE FOR DRY LOCATIONS ONLY. DO NOT
IMMERSE IN WATER. NOT FOR USE WHERE DIRECTLY
EXPOSED TO WATER.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following conditions:
1. This device may not cause harmful interference,
2. This device must accept any interference
received, including interference that may cause
undesired operation.
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate
radio frequency energy and, if not installed and
used according to instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will
not occur in any given installation.
If this equipment causes harmful interference to
radio or television reception, the user may try to
correct the interference by taking one or more of the
following measures:
- Reorient or relocate receiving antenna
- Increase the separation between equipment and
receiver
- Connect equipment into a separate outlet or
circuit from receiver
- Consult the dealer or an experienced radio/TV
technician for additional assistance
All brand names displayed are trademarks of their
respective holders.
© Zooz 2022
WARRANTY
This product can be included and operated
in any Z-Wave network with other Z-Wave
certified devices from other manufacturers
and/or other applications. All non-battery
operated nodes within the network will act
as repeaters regardless of vendor to increase
reliability of the network.
This product features the latest Security 2
(S2) framework to remove smart home
network hacking risks. This de-vice is
equipped with a unique authentication
code for trusted wireless communication.
S2
Z-WAVE STICK AS SECONDARY CONTROLLER
You can use the S2 stick as a secondary
controller with your existing Z-Wave system
if it accepts additional con-trollers. To enroll
the S2 stick in your current system, send the
inclusion command and put the S2 stick into
learning mode, using the SerialAPI mode.