ZooZ S2 STICK User manual

S2 STICK
ZST10
USER MANUAL
www.getzooz.com
FEATURES
ŸZ-Wave Plus Static USB Controller
ŸLatest S2 security protocol for a truly private network
ŸWorks with Smart Start Z-Wave devices
ŸExtended range up to 130 feet indoors and up to 500
feet in open space
ŸZ-Wave Plus chip for faster command processing
ŸLED indicator signals wireless communication in
progress for efficient troubleshooting
ŸNo drivers needed: works out of the box on Windows,
Linux, and MAC OS
SPECIFICATIONS
ŸModel Number: ZST10
ŸZ-Wave Frequency: 908.42 MHz
ŸPower: 4.75-5.25 VDC
ŸSDK: 6.81.02
ŸRange: Up to 130 feet indoors
ŸOperating Temperature: 14-104° F
ŸInstallation and Use: Indoor only
ŸDimensions: 3.5” x 1” x 0.4”
SET-UP
Use this S2 Z-Wave Plus USB Stick as a Z-Wave radio for
your DIY smart home system. Simply connect it to a USB
port on your PC, laptop, or Raspberry Pi and match it
with home automation soware (host soware) of your
choice to enjoy a fully secure, private Z-Wave Plus mesh
network.
Questions? [e-mail]
WINDOWS SET-UP
Windows 2000, XP, Vista, 7, 8 (32 / 64 bit)
The device will display in Device Manager under Ports.
You can access it through the Windows CreateFile API
using “//.//COMxxx” where xxx stands for the COM port
number assigned by Windows.
UZB.INF and UZB.CAT are listed in the Z-Wave SDK which
uses the standard usbser.sys or usbser64.sys Windows
driver.
LINUX SET-UP
Linux kernel 2.6.24+
The device will display as “/dev/ttyACMxx” where xx
stands for the tty number assigned by Linux.
MAC OS SET-UP
MAC OS X 6.4
The device will display as “/dev/tty.usbmodemxxx” where
xxx stands for the tty number assigned by Mac OS.
SerialAPI Mode:
Once the S2 stick is plugged into the USB port of
the host computer, it automatically enrolls in the
SerialAPI mode and remains active (awake), always
listening for commands sent from the host so-
ware and relaying them to the Z-Wave devices in
the network. It acts as a Z-Wave signal adapter for
your smart home system, translating any Z-Wave
reports and notifications sent by devices in your
network to your smart home interface.
To get a full list of supported SerialAPI functions, go
to support.getzooz.com and search for S2 Stick
SerialAPI functions.

FACTORY RESET
The S2 stick can only be reset by the host soware while
it’s in SerialAPI mode. The device is reset once an
appropriate command from the host soware is sent to
reset the Z-Wave network.
There is no way to manually reset the S2 stick if it’s not
controlled by host soware.
S2 STICK AS SECONDARY CONTROLLER
You can use the S2 stick as a secondary controller with
your existing Z-Wave system if it accepts additional con-
trollers. To enroll the S2 stick in your current system,
send the inclusion command and put the S2 stick into
learning mode, using the SerialAPI mode.
WARNINGWARNING
ŸThis product should be installed indoors upon
completion of any building renovations.
ŸDo not install the S2 Stick in a place with direct sun
exposure, high temperature, or humidity.
ŸKeep away from chemicals, water, and dust.
ŸEnsure the device is never close to any heat source or
open flame to prevent fire.
ŸEnsure the device is connected to an electric power
source that does not exceed the maximum load power.
ŸNo part of the device may be replaced or repaired by
the user.
This product is covered under a 12-month limited
warranty. To read the full warranty policy or file a
warranty claim, please go to:
www.getzooz.com/warranty
FCC NOTE
THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV
INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO
THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S
AUTHORITY TO OPERATE THE EQUIPMENT. STORE INDOORS WHEN
NOT IN USE. SUITABLE FOR DRY LOCATIONS ONLY. DO NOT
IMMERSE IN WATER. NOT FOR USE WHERE DIRECTLY EXPOSED TO
WATER.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following conditions:
1. This device may not cause harmful interference,
2. This device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used according to instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in
any given installation.
If this equipment causes harmful interference to radio or television
reception, the user may try to correct the interference by taking
one or more of the following measures:
- Reorient or relocate receiving antenna
- Increase the separation between equipment and receiver
- Connect equipment into a separate outlet or circuit from receiver
- Consult the dealer or an experienced radio/TV technician for
additional assistance
All brand names displayed are trademarks of their respective
holders.
© Zooz 2018
WARRANTY
This product can be included and operated in any Z-
Wave network with other Z-Wave certified devices from
other manufacturers and/or other applications. All non-
battery operated nodes within the network will act as
repeaters regardless of vendor to increase reliability of
the network.
This product features the latest Security 2 (S2) framework
to remove smart home network hacking risks. This de-
vice is equipped with a unique authentication code for
trusted wireless communication.
S2