ZooZ ZEN71 800LR User manual

SPECIFICATIONS
ON/OFF SWITCH 800
ZEN71 800LR
USER MANUAL
FEATURES
ŸManual or Z-Wave on/off control with instant status updates
Ÿ800 series Z-Wave chip for better range and faster control
ŸDirect 3-Way: works with regular on/off switches in a 3-way
ŸScene control: trigger actions with multi-tap (select hubs only)
ŸSmart bulb mode: disable relay and control the light via Z-Wave
ŸZ-Wave Long Range for ultra reliable no-mesh communication
ŸRemembers and restores on/off status aer power failure
ŸAdjustable LED indicator in 4 colors and 3 brightness levels
ŸWorks with LED and incandescent bulbs (don’t use with tubes)
ŸModel Number: ZEN71 800LR
ŸZ-Wave Signal Frequency: 908.42 MHz
ŸPower: 120 VAC, 60 Hz
ŸMaximum Load: , 960W Incandescent, 150W LED or CFL bulbs
1800W (15A) Resistive, 3A motor (DON’T use with receptacles)
ŸRange: Up to 500 feet line of sight
ŸOperating Temperature: 32-104° F (0-40° C)
ŸInstallation and Use: Indoor only
CAUTION
This is an electrical device - please use caution when installing and
operating the on/off switch. Remote control of appliances may result in
unintentional or automated activation of power.
Do not use this Z-Wave device to control electric heaters or other
appliances which produce the risk of fire, burns, or electrical shock
when unattended.
To reduce risk of overheating and possible damage to other equipment,
do not install this unit to control a receptacle; a motor-operated
appliance; a fluorescent lighting fixture; or a transformer-supplied
fixture.
WIRING: READ IT!
This switch is intended for installation in accordance with the
National Electric Code and local regulations. It is recommen-
ded that a licensed electrician perform this installation.
BEFORE YOU INSTALL
1. CHECK THE LOAD: lights only (150W for LED’s, 600W for
incande-scent), DON’T CONNECT THIS SWITCH TO OUTLETS
OR TUBE LIGHTS.
2. POWER OFF: turn the circuit power off in the breaker panel
before you start. If installing in a multi-switch box with
multiple circuits, turn power off at all of the circuits.
3. CHECK THE WIRES: mark load (most oen black), line
(most oen black), neutral (most oen white), and ground
(most oen bare). 14 AWG wires only! Don’t rely exclusively
on your multimeter to identify the wires!
4. REMOVE THE OLD SWITCH: disconnect the wires and label
them with the included label stickers.
5. CONNECT THE Z-WAVE SWITCH: follow all installation
steps carefully. Wire the switch EXACTLY like in the diagram.
1 Insert the ground (bare) wire into the Ground terminal
(not shown in the diagram)
ZEN71 WIRING DIAGRAM FOR SINGLE POLE INSTALLATION
1. UNSCREW: carefully turn the screw counter
clockwise to make space for the wire. DO NOT
unscrew completely.
2. PRESS DOWN: once it’s loose, press the screw
down with your finger so it catches the thread.
3. INSERT WIRE: make sure the wire is perfectly
straight, then insert it into the terminal while
holding the screw down. DO NOT wrap wires
around the terminal screws!
4. TIGHTEN: turn the screw clockwise to tighten
the wire. DO NOT OVERTIGHTEN!
HOW TO INSTALL THE WIRES
1.
2.
3.
Secure your Z-Wave switch in the box with mounting screws,
handling the wires with care.
Install the wall plate and restore power to the circuit.
COMPLETE INSTALLATION
The LED indicator should light up as soon as you turn the power
back on if the switch (light) is OFF. Tap the upper paddle for ON
and lower paddle for OFF. If the test fails, please check that:
Ÿpower is fully restored to the circuit
Ÿwiring matches the instructions exactly
Ÿthe load isn’t too large and overheating the switch causing it to
shut off
TEST THE SWITCH
ŸThis product should be installed indoors upon completion of any building renovations.
ŸPrior to installation, the device should be stored in a dry, dust-and-mold-proof place.
ŸDo not install the switch in a place with direct sun exposure, high temperature, or humidity.
ŸKeep away from chemicals, water, and dust.
ŸEnsure the device is never close to any heat source or open flame to prevent fire.
ŸEnsure the device is connected to an electric power source that does not exceed the
maximum load power.
ŸNo part of the device may be replaced or repaired by the user.
WARNING
PAGE 1 PAGE 2 PAGE 3
ADVANCED SETTINGS
Please refer to your controller's user guide for advanced
programming instructions as they are a little different for
every soware.
Not sure where to start? Go to www.support.getzooz.com
for detailed instructions on how to change the settings
on SmartThings, Vera, and more.
Or just email us: [e-mail]
ASSOCIATION
This on/off switch supports Group 1 with up to 1 devices for
lifeline communication and Group 2 with up to 5 devices.
This device will send BASIC REPORT to Group 1 and BASIC
SET command to group 2 when operated manually.
You can set direct association to have the switch control
another Z-Wave device independently of the hub by using
Group 2. Not every hub exposes direct association settings in
the interface so please go to www.support.getzooz.com to
see if your system allows for direct association.
WARRANTY
This product is covered under a 1-year limited warranty and
extender 5-year warranty once registered. To read the full
warranty policy or file a warranty claim, please go to
www.getzooz.com/warranty
IN NO EVENT SHALL ZOOZ OR ITS SUBSIDIARIES AND AFFILIATES BE LIABLE FOR ANY INDIRECT,
INCIDENTAL, PUNITIVE, SPECIAL, OR CONSEQUENTIAL DAMAGES, OR DAMAGES FOR LOSS OF PROFITS,
REVENUE, OR USE INCURRED BY CUSTOMER OR ANY THIRD PARTY, WHETHER IN AN ACTION IN CONTRACT,
OR OTHERWISE EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DA-MAGES. ZOOZ'S LIABILITY AND
CUSTOMER'S EXCLUSIVE REMEDY FOR ANY CAUSE OF ACTION ARISING IN CON-NECTION WITH THIS
AGREEMENT OR THE SALE OR USE OF THE PRODUCTS, WHETHER BASED ON NEGLIGENCE, STRICT
LIABILITY, BREACH OF WARRANTY, BREACH OF AGREEMENT, OR EQUITABLE PRINCIPLES, IS EXPRESSLY
LIMITED TO, AT ZOOZ'S OPTION, REPLACEMENT OF, OR REPAYMENT OF THE PURCHASE PRICE FOR THAT
PORTION OF PRODUCTS WITH RESPECT TO WHICH DA-MAGES ARE CLAIMED. ALL CLAIMS OF ANY KIND
ARISING IN CONNECTION WITH THIS AGREEMENT OR THE SALE OR USE OF PRODUCTS SHALL BE DEEMED
WAIVED UNLESS MADE IN WRITING WITHIN THIRTY (30) DAYS FROM ZOOZ'S DELIVERY, OR THE DATE FIXED
FOR DELI-VERY IN THE EVENT OF NONDELIVERY.
FCC NOTE
THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED
MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO
OPERATE THE EQUIPMENT. STORE INDOORS WHEN NOT IN USE. SUITABLE FOR DRY LOCATIONS ONLY. DO NOT
IMMERSE IN WATER. NOT FOR USE WHERE DIRECTLY EXPOSED TO WATER.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following conditions:
1. This device may not cause harmful interference,
2. This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential
installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used according
to instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in any given installation.
If this equipment causes harmful interference to radio or television reception, the user may try to correct the
interference by taking one or more of the following measures:
- Reorient or relocate receiving antenna
- Increase the separation between equipment and receiver
All brand names displayed are trademarks of their respective holders.
© Z
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
ooz 2023
STRIP WIRE AT 1/2-5/8”
Z-WAVE CONTROL
1. ADD DEVICE to your hub
Initiate inclusion (pairing) in the app (or web
interface).
Not sure how? Scan one of the QR codes
below for step-by-step instructions or get in
touch: www.support.getzooz.com
The LED indicator will blink blue to signal communication
and turn green for 3 seconds if inclusion is successful or turn
red for 3 seconds if the pairing attempt fails.
FIRMWARE VER: 3.10
1. Bring your Z-Wave gateway (hub) close to the switch if
possible
2. Put the Z-Wave hub into exclusion mode (not sure how to
do that? [e-mail])
3. Tap the lower paddle on the switch 3 times quickly (the
LED indicator will start blinking blue)
4. Your hub will confirm exclusion, the LED indicator on the
switch will turn green for 3 seconds, and the device will
disappear from your controller's device list
EXCLUSION (REMOVING / UNPAIRING DEVICE)
FACTORY RESET
If your primary controller is missing or inoperable, you may
need to reset the device to factory settings. To reset the
switch, press and hold the lower paddle for 10 seconds
until the LED indicator starts blinking. Release paddle, and
immediately aer, tap the lower paddle 5 times to
complete the reset. The LED indicator will flash blue 3 times
and turn red for 3 seconds to confirm successful reset.
NOTE: All previously recorded activity and custom settings will be erased from
the device’s memory.
TROUBLESHOOTING
The switch won’t add to your system? Try this:
1. Initiate EXCLUSION and tap the lower paddle 3 times
quickly.
2. Tap the upper paddle 4-5 times quickly when adding it.
3. Bring the gateway controller (hub) closer to the switch, it
may be out of range.
4. Get troubleshooting tips for your hub at
www.support.getzooz.com
The switch won’t control the lights manually anymore?
Try this:
1. Turn the power off at the breaker and check if a wire
didn’t get loose.
2. Exclude the switch from the hub or reset it in case
manual control was accidentally disabled.
3. The load may be incompatible so try it with a single
incandescent bulb.
SmartThings Hubitat Z-Box Hub
Choose your hub and scan the QR code with your phone’s
camera. Then click on the link to access the step-by-step
pairing instructions.
Get more tutorials and helpful tips at ww.support.getzooz.com
Home Assistant This product can be included and operated in any Z-Wave
network with other Z-Wave certified devices from other
manufacturers and/or other applications. All non-battery
operated nodes within the network will act as repeaters
regardless of vendor to increase reliability of the network.
This product features the latest Security 2 (S2) framework to
remove smart home network hacking risks. This device is
equipped with a unique authentication code for trusted
wireless communication.
This is an ETL certified device. ETL, just like UL, is a
Nationally Recognized Testing Laboratory. The ETL mark is
proof of product compliance with North American safety
standards.
www.getzooz.com
[e-mail]
2 Insert the power source wire to Line terminal and load
wire to Load terminal. Load and line CAN’T be swapped
so make sure you identified them correctly!
3 Run the white
jumper (included in
the box) from the
bundle of white wires
to the Neutral
terminal
SEE BACK PAGE
FOR 3-WAY & 4-WAY
DIAGRAMS AND
INSTRUCTIONS
DON’T FORCE THE SCREWS. Look up to see
how to install the wires correctly.
µNOT SURE WHAT YOU’RE SEEING? WE’LL HELP! SUPPORT.GETZOOZ.COM
SEND US PICTURES OF YOUR SET-UP, BEFORE YOU DISCONNECT WIRES.
TAP UP 3 TIMES QUICKLY
2. Finalize inclusion at the switch.
if using traditional Z-Wave inclusion.
SCAN THE QR CODE / ENTER THE 5-DIGIT DSK
if using the new SmartStart method.
NEED SOME HELP? [e-mail]
CUSTOMIZE YOUR SWITCH
Here is a selection of settings available to customize your
switch. Scan the QR code for a full list of parameters and
look below for how to access them on your hub.
ŸLED Indicator behavior, color, brightness:
6 x TAP UP to change the indicator mode
ŸSmart Bulb Mode (disable the relay):
HOLD UP for 10 seconds then 5 x TAP UP
ŸOn/off status aer power failure
SCENE CONTROL
SmartThings Hubitat Z-Box Hub
Choose your hub and scan the QR code with your phone’s
camera. Then click on the link to learn how to access and
change the advanced settings for the switch on your hub.
Home Assistant
You can trigger scenes or control other connected devices in
your network using this switch. Just enable the setting in
Parameter 9 and verify that your hub supports scene control.
Assign scenes or actions to 1-tap, 2-tap, 3-tap, 4-tap, and 5-
tap as well as to held and released for any of the paddles.
Scan the QR code for scene control
programming instructions on your hub.
QUESTIONS?
[e-mail]
SCAN SETTINGS
Scan to register
your product for
extended warranty
and direct access to
firmware files.
S2

ZEN71 WIRING DIAGRAMS FOR THE MOST COMMON 3-WAY INSTALLATIONS For more diagrams or to request custom
instructions go to support.getzooz.com
Wire and screw position, as well as color codes
are for illustration only. You should not follow the
colors and positioning in the illustration blindly.
Always identify all wires prior to installing Zooz
switches and make sure you can match the
diagrams to your set-up exactly. Don’t
experiment or attempt a “trial-and-error”
installation for your own safety. Don’t disconnect
any wires before documenting your set-up in
each box with detailed images!
STOP!
NOTE!
If you are not comfortable identifying the wiring
and completing the installation, please consult a
licensed electrician.
Make sure you have identified all wiring correctly
before connecting the switch. If your wiring
doesn’t match any of the below diagrams,
contact our support: [e-mail]
ON/OFF SWITCHES ONLY
Do not connect Zooz Z-Wave switches to an
existing 3-way dimmer, illuminated switch, or
an electronic add-on switch. Zooz switches can
only be wired with mechanical on/off or
momentary switches in a 3-way or 4-way setting!
To simplify the diagrams, we did not include
connections for the ground wire. Remember that
all Zooz switches need to be wired according to
the electrical code, with ground wire connected
to the ground terminal.
POWER OFF!
Cut power to the circuit before handling the
wiring.
Always install your Zooz switch in the box
with direct connection to power line.
Diagrams and instructions in this manual
are for ZEN71 and ZEN72 models ONLY!
ZEN71 4-WAY INSTALLATION WIRING DIAGRAM (LINE AND LOAD MUST BE IN THE SAME BOX)
EACH BOX NEEDS TO BE REWIRED ACCORDING TO
THE 4-WAY DIAGRAM.
Follow this diagram ONLY if you confirmed you
have direct connection to power and light in the
same box. If they’re in separate boxes, use the
ZEN26 / ZEN76 model instead or ask us about
using the ZEN71 switch with ZAC99 momentary
switches in 4-way and 5-way installations.
If you have power or load coming into the box
with the 4-way switch, contact us for custom
instructions: [e-mail]
USE IT WITH SMART BULBS!
Want to control your smart bulb from a wall switch without cutting power to it every time you turn the light off from the switch?
We’ll tell you how, just ask!
NEED HELP?
If you’re having trouble reading the
diagrams or don’t see your wiring set-up
here, get in touch! We have more 3-way,
4-way, and 5-way diagrams and
instructions. There are many ways to wire
multi-point control set-ups so unless you
can match your wiring to the diagrams
here, please don’t attempt the installation
for your own safety.
www.support.getzooz.com
[e-mail]
You can now easily check if the switch is within your Z-Wave
hub’s range:
Press and hold the lower paddle for 10 seconds until the LED
indicator starts blinking. Release the paddle and within 2
seconds, tap the lower paddle 2 times quickly. The LED
indicator will then report signal strength.
Solid green = direct communication with the primary controller
is stable
Flashing green = direct communication with the primary
controller is established but signal is weak
Solid blue = stable communication with hub via repeaters
Flashing blue = communication with the primary controller is
established via repeaters but signal is weak
Solid red = communication with the primary controller has
failed
Tap the lower paddle to exit testing mode.
NOTE: This function may only be activated once the switch has
been included to a Z-Wave network.
RANGE TEST TOOL
The white paddles on the ZEN71 switch can
be replaced for a different color!
Please get in touch with our support to check
which colors are currently available and how
to order replacement paddles.
Zooz switches will match the shade of
standard Leviton switches and wall plates
available at any major retailer.
MORE COLOR?
3-WAY DIAGRAM FOR 2-POINT CONTROL WITH ZEN71 AND REGULAR 3-WAY SWITCH: OPTION 1
ZEN71 3-WAY SWITCH
NEUTRAL
3-WAY DIAGRAM FOR 2-POINT CONTROL WITH ZEN71 AND REGULAR 3-WAY SWITCH: OPTION 2
ZEN71 3-WAY SWITCH
REWIRE BOTH BOXES!
REWIRE BOTH BOXES!
NEUTRAL
ZEN71
CHECK 3-WAY / 4-WAY TYPE!
Your 3-way and 4-way switches may have a different terminal
layout so identify the in and out terminals on the 4-way switch and
the common terminal on the 3-way switch before the installation.