StarTech.com SV231HDMIUA User manual

Manual Revision: 05/01/2014
For the most up-to-date information, please visit: www.startech.com
DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
SV231HDMIUA
2 Port USB HDMI KVM Switch with Audio
and USB 2.0 Hub
*actual product may vary from photos

Instruction Manual
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not
represent an endorsement of a product or service by StarTech.com, or an endorsement of the
product(s) to which this manual applies by the third-party company in question. Regardless
of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of
their respective holders.

Instruction Manual
i
Table of Contents
Introduction............................................................................................1
Packaging Contents ................................................................................................................................. 1
System Requirements.............................................................................................................................. 1
Installation ..............................................................................................2
Front View................................................................................................2
Rear View .................................................................................................2
Hardware Installation .............................................................................................................................. 3
Driver Installation...................................................................................................................................... 4
Operation ................................................................................................4
Front Panel................................................................................................................................................... 4
HotKey Control........................................................................................................................................... 5
Alternative Hotkey Commands............................................................................................................ 7
Change Leading Hotkey......................................................................................................................... 8
Specications..........................................................................................9
Technical Support ..................................................................................10
Warranty Information............................................................................10

Instruction Manual
1
Introduction
The SV231HDMIUA 2-port USB HDMI® KVM Switch lets you control two USB-enabled
multimedia computers or devices with HDMI video interfaces, using a single peripheral
set/console (USB keyboard, mouse, monitor, speakers and microphone).
A highly versatile KVM solution, the USB HDMI KVM Switch features an integrated
2-port USB 2.0 hub that lets selected computers access shared high speed USB devices,
eliminating the cost of duplicate USB peripheral purchases.
Ensuring high quality video capability, the HDMI KVM switch supports HD resolutions
of up to 1920 x 1200. Oering genuine digital signal transmission over the cable, this
switch can be used to share one HD panel between multiple HDMI sources such as Blu-
Ray players, Video Game consoles and HD media centers.
The switch also supports audio and microphone switching functions and allows you to select
connected computers, USB device hub ports and audio/mic channels either simultaneously
or independently using either front-panel push-buttons or keyboard hotkeys.
Packaging Contents
• 1x 2 Port HDMI KVM
• 1x Package of Rubber feet
• 1x Power Adapter
• 1x User Manual
System Requirements
• HDMI and USB enabled computer systems
• HDMI enabled display device (e.g. monitor, projector, TV, etc.)
• Standard 104-key wired USB keyboard
• Standard 3-button wired USB mouse

Instruction Manual
2
Installation
NOTE: Prior to the installation, please power o all devices that will be connected to
this system.
Ensure that all devices you will connect are properly grounded.
Place cables away from uorescent lights, air conditioners, and machines that are likely
to generate electrical noise.
If you experience any problems using a USB KVM switch, the following BIOS setup
changes may be necessary for PC users (not necessary for Mac users):
• Set HALT ON ERROR to ALL BUT KEYBOARD.
• In PNP AND PCI SETUP, set PNP OS INSTALLED to YES and set USB IRQ to ENABLED.
Dierent systems may use dierent naming, so contact your system manufacturer for
further assistance with these settings.
Front View
Rear View
Port Selection
Link LED
Port Selection
Button

Instruction Manual
3
Hardware Installation
1. Plug a monitor/display into the Console HDMI connector; plug a USB keyboard and
a USB mouse into the dedicated USB keyboard and mouse ports on the KVM switch.
2. Use a male-to-male HDMI video cable to connect the HDMI connector on the
computer’s/devices’video card, to one of the KVM’s PC ports (ie. PC1)
3. Use a USB type A-B Cable to connect the KVM’s USB port (type B, square connector) for the
PC port used in Step 2, and the USB port on the computer/device (type A, at connector).
4. Use a male-to-male 3.5mm mini-jack audio cable to connect the speaker and
microphone connectors on the computer/device to the KVM’s speaker/mic ports for
the PC port used in Step 2.
5. Repeat for Steps 2 thru 4 for each PC port on the KVM switch, or each computer/
device you wish to use on the KVM.
6. OPTIONAL: Connect any other USB peripherals you wish to share between the
connected computers/devices to the extra USB Hub ports on the Console side.
7. Connect the external power adapter from a wall outlet to the power connector on
the rear panel of the KVM switch.
8. Power up the rst computer/device and wait for it to fully boot and test keyboard/
mouse functionality.
9. Once operation has been successfully conrmed, switch to the next port and power
up that computer/device and conrm.
10. Once completed for all computers/devices connected to the KVM switch, you
should be able to switch between ports freely.
*Console setup

Instruction Manual
4
Driver Installation
No driver installation is required for the KVM switch, as the keyboard and mouse
use generic USB keyboard/mouse drivers that are already installed on any operating
system that fully supports USB.
Operation
Front Panel
Port Selection/Link LED
The LED turns green when the connected computer is powered-on. The corresponding
LED will also illuminate red when that PC port is currently selected.
Port Selection Button
Pushing the front panel “Select”button toggles between the PC ports on the KVM switch.

Instruction Manual
5
HotKey Control
A Hotkey command is a short keyboard sequence for selecting a computer, activating
computer scan, etc. A hotkey sequence starts with two left <CTRL> keystrokes
(successively within 0.2 seconds) followed by one or two more keystrokes. A built-in
tone generator creates a high-pitch beep for correct hotkey command; otherwise, one
low-pitch beep is generated for errors and the bad key sequence will not be forwarded
to the selected computer.
NOTE: Press and hold Left <SHIFT> and press <NumLock> twice, then release <SHIFT>
followed by pressing left <CTRL> once, which will enable / disable the hotkey feature.
To select a computer:
Left <CTRL> + Left <CTRL> + <1>
(Example: Selects the computer at port 1.)
Left <CTRL> + Left <CTRL> + <2>
(Example: Selects the computer at port 2.)
NOTE: Do not use the keypad on the right-side of the keyboard.
Auto Scan
The KVM automatically scans through the powered-on computers in sequence on a
xed time interval (see Scan Time below).
To start Auto Scan:
Left <CTRL> + Left <CTRL> + <F1>
To abort the Auto Scan mode, press the left <CTRL> key twice.
NOTE: When Auto Scan detects any keyboard or mouse activity, it suspends the
scanning till the activity stops; it then resumes with the next computer in sequence.
The length of the Auto Scan interval (Scan Rate) is adjustable, see below.

Instruction Manual
6
Manual Scan allows users to manually switch back and forth between powered-on computers.
Left <CTRL> + Left <CTRL> + <F2>
To select the previous or the next computer, press <UP> or <DOWN> arrow keys. To
abort the Manual Scan, press any other key.
Scan Time
Four options are available for users to set the Scan Time duration, it Includes 3, 8, 15
and 30 seconds.
Note: Scan Time is set to 3 seconds by default.
To adjust Scan Rate, set the scan time of duration before switching to the next computer:
Left <CTRL> + Left <CTRL> + <F3>
The KVM Switch generates 1 to 4 beeps indicating a scan time duration for 3, 8, 15 or
30 seconds respectively.
Audio Lock
There are two options for Audio Lock: ON and OFF. When ON, audio selection follows
computer selection. When OFF, the current port’s audio is used for all other ports. It
is useful if you want to listen to a particular computer’s audio signal while operating
other computers.
Left <CTRL> + Left <CTRL> + <F5>
The KVM switch beeps once or twice corresponding to ON and OFF respectively.
To change which port the audio is following to the currently selected port, press the
following hotkey:
Left <CTRL> + Left <CTRL> + <A>

Instruction Manual
7
Alternative Hotkey Commands
In addition to the Left <CTRL> + Left <CTRL> hotkeys, there are two alternative hotkey
sequences available.
1. For the following operations, users may press <ScrollLock> twice instead of pressing
left <CTRL> twice.
To select a computer:
<ScrollLock> + <ScrollLock> + <1>
(Example: Select the computer at port 1.)
<ScrollLock> + <ScrollLock> + <2>
(Example: Select the computer at port 2.)
NOTE: Do not use the keypad at the right of the keyboard.
2. For those keyboards that do not have or support <ScrollLock>, please press and
HOLD the Left <SHIFT> and press <NumLock> twice instead of pressing Left
<CTRL> twice.
To select a computer:
hold Left <SHIFT> + press <NumLock> + press <NumLock>
then release <SHIFT> + press <1>
Example: Select the computer at port 1.)
hold Left <SHIFT> + press <NumLock> + press <NumLock>
then release <SHIFT> + press <2>
(Example: Select the computer at port 2.)
NOTE: Do not use the keypad at the right of the keyboard.