Zotac ECM74060C User manual

ZOTAC ZBOX
1
ZOTAC ZBOX
User’s Manual
No part of this manual, including the products and software described in it, may
be reproduced, transmitted, transcribed, stored in a retrieval system, or translated
into any language in any form or by any means, except documentation kept by the
purchaser for backup purposes, without the express written permission of ZOTAC.
Products and corporate names mentioned in this manual may be registered trademarks
or copyrights of their respective companies, and are used for identication purposes
only. All trademarks are the property of their respective owners.
Every e󰀨ort has been made to ensure that the contents of this manual are correct and
up to date. However, the manufacturer makes no guarantee regarding the accuracy of
its contents, and reserves the right to make changes without prior notice.
CAUTION:
Risk of explosion if the battery is replaced with an incorrect type. Batteries should be
recycled where possible. Disposal of used batteries must be in accordance with local
environmental regulations.

ZOTAC ZBOX
2
Table of Contents
Product Specications ----------------------------------------------------------------------------------------3
Safety information ----------------------------------------------------------------------------------------------4
Setting up your system-------------------------------------------------------------------------------------4
Care during use ----------------------------------------------------------------------------------------------4
Welcome -----------------------------------------------------------------------------------------------------------5
Package contents -------------------------------------------------------------------------------------------5
Getting to know your ZOTAC ZBOX ----------------------------------------------------------------------6
Front view -----------------------------------------------------------------------------------------------------6
Rear view ------------------------------------------------------------------------------------------------------7
Installing Hardware--------------------------------------------------------------------------------------------- 8
Installing a graphics card ----------------------------------------------------------------------------------10
Installing a memory module-------------------------------------------------------------------------------12
Installing M.2 SSD and Optane memory modules --------------------------------------------------14
Installing a hard disk / SSD -------------------------------------------------------------------------------17
Setting up your ZOTAC ZBOX ------------------------------------------------------------------------------19
Installing drivers and software -----------------------------------------------------------------------------21
Installing an operating system----------------------------------------------------------------------------21
Installing system drivers -----------------------------------------------------------------------------------21
Installing the Killer Control Center-----------------------------------------------------------------------23
Using your ZOTAC ZBOX-------------------------------------------------------------------------------------27
Conguring a wireless connection ----------------------------------------------------------------------27
Conguring audio output-----------------------------------------------------------------------------------27
Intel® OptaneTM technology-----------------------------------------------------------------------------------28
Enabling Intel Optane memory---------------------------------------------------------------------------28
Disabling Intel Optane memory --------------------------------------------------------------------------35

ZOTAC ZBOX
3
Product Specications
qMicroprocessor support
vIntel Core i7-10700 (8-core, 2.9 GHz, up to 4.8 GHz) for ZBOX ECM73070C/
ZBOX ECM7307LH/ ZBOX ECM74060C
vIntel Core i5-10400 (6-core, 2.9 GHz, up to 4.3 GHz) for ZBOX ECM53060C
qChipset
vIntel H470
qGraphics support
vNVIDIA GeForce RTX 3070 w/ 8GB GDDR6, 256bit for ZBOX ECM73070C
vNVIDIA GeForce RTX 3070 LHR w/ 8GB GDDR6, 256bit for ZBOX ECM7307LH
vNVIDIA GeForce RTX 4060 w/ 8GB GDDR6, 128bit for ZBOX ECM74060C
vNVIDIA GeForce RTX 3060 w/ 12GB GDDR6, 192bit for ZBOX ECM53060C
1x HDMI 2.1, 3x DP 1.4a
vIntel UHD Graphics 630 (Use only when a dedicated graphics card is not installed)
1x HDMI 1.4
qOperating systems
vWindows 10 64-bit & Windows 11 Ready
qSystem Memory support
v2x DDR4-2933 SODIMM slots for ZBOX ECM73070C/ ZBOX ECM7307LH
v2x DDR4-2933/2666 SODIMM slots for ZBOX ECM74060C
v2x DDR4-2666 SODIMM slots for ZBOX ECM53060C
vUp to 64 GB of memory
qUSB Ports
v4x USB 3.1 GEN2 10 Gbps
v4x USB 3.0 5 Gbps (1x Type-C and 3x Type-A)
qOnboard Serial ATA
vSATA 6.0 Gb/s transfer rates
v2.5“ SATAIII HDD/SSD bay
qExpansion slot
v1x M.2 PCIe x4/ SATA III SSD slot (22/42, 22/80)
v1x M.2 PCIe x4 SSD/ Optane Memory M10 slot (22/42, 22/80, 22/110)
q Onboard Dual LAN
v1 x Killer E3000 2.5Gbit LAN (10/100/1000/2500Mbps)
v1 x 10/100/1000 Mbps Ethernet

ZOTAC ZBOX
4
q WiFi 6/ Bluetooth support
vKiller WiFi 802.11 ax, BT 5.2
qProduct Size
v265.5mm x 126mm x 249mm
Safety information
Your ZOTAC ZBOX is designed and tested to meet the latest standards of safety for information
technology equipment. However, to ensure your safety, it is important that you read the following safety
instructions.
Setting up your system
vRead and follow all instructions in the documentation before operating your system.
vDo not use this product near water or a heat source such as a radiator.
vSet up the system on a stable surface with the provided stand. Never use the system alone
without the stand.
vOpenings on the chassis are for ventilation. Do not block or cover these openings. Make sure
you leave plenty of space around the system for ventilation. Never insert objects of any kind into
the ventilation openings.
vUse this product in environments with ambient temperatures between 0℃and 35℃.
Care during use
vDo not walk on the power cord or allow anything to rest on it.
vDo not spill water or any other liquids on your system.
vWhen the system is turned o󰀨, a small amount of electrical current still ows. Always unplug all
power, modem, and network cables from the power outlets before cleaning the system.
vIf you encounter the following technical problems with the product, unplug the power cord and
contact a qualied service technician or your retailer.
The power cord or plug is damaged.
Liquid has been spilled into the system.
The system does not function properly even if you follow the operating instructions.
The system was dropped or the cabinet is damaged.
The system performance changes.

ZOTAC ZBOX
5
Welcome
Congratulations on your purchase of the ZOTAC ZBOX. The following illustration displays the package
contents of your new ZOTAC ZBOX. If any of the below items are damaged or missing, contact your
retailer.
Package contents
• 1 x ZOTAC ZBOX
• 1 x Power Cord
• 2 x Nylon Cable Tie (optional)
• 2 x Antenna
• 1 x USB ash drive with Windows drivers
• 1 x Quick Start Guide & Warranty Card

ZOTAC ZBOX
6
Getting to know your ZOTAC ZBOX
Front view
Refer to the diagram below to identify the components on this
side of the system
1. Power switch
The power switch allows powering ON and OFF the system.
2. Combo Headphone/Microphone jack (3.5mm)
The combo headphone/microphone jack (3.5mm) is used to
connect the system’s audio out signal to amplied speakers,
3-pole headphones or 4-pole CTIA headphones.
Note: The combo headphone/microphone jack does not
support the traditional microphone.
3. Memory card slot
The Memory card slot is compatible with SD/SDHC/SDXC
cards used in devices like digital cameras, MP3 players, mobile
phones and PDAs.
4. Power LED
The Power LED is always ON when power is on.
5. WiFi LED
The WiFi LED is always ON when WiFi was active.
1
2
3
456
7
8
6. Hard disk LED
The hard disk LED blinks when data is being written into or read from the hard disk drive.
7. USB 3.0 ports
The USB 3.0 port supports the SuperSpeed USB 3.0 devices and is backwards compatible
with USB 2.0/1.1 devices. Use this port for USB 3.0 devices for maximum performance with
USB 3.0 compatible devices.
8. USB 3.0 Type-C port
The USB 3.0 type-C port supports the SuperSpeed USB 3.0 devices. Use this port for USB
3.0 devices for maximum performance with USB 3.0 compatible devices.

ZOTAC ZBOX
7
Rear view
Refer to the diagram below to identify the components on this side
of the system.
1. WiFi antenna connectors
The WiFi antenna connector supports WiFi antenna module.
2. LAN ports
The eight-pin RJ-45 LAN ports support standard Ethernet
cables for connection to a local network. The LAN port marked
with K is for Killer Ethernet.
3. USB 3.1 port
The USB 3.1 port supports the SuperSpeed USB 3.1 devices
and is backwards compatible with USB 3.0/2.0/1.1 devices.
Use this port for USB 3.1 devices for maximum performance
with USB 3.1 compatible devices.
4. USB 3.0 ports
The USB 3.0 port supports the SuperSpeed USB 3.0 devices
and is backwards compatible with USB 2.0/1.1 devices. Use
this port for USB 3.0 devices for maximum performance with
USB 3.0 compatible devices.
1
2 3
4
5
6
7
1
5
5. HDMI ports
The HDMI (High Denition Multimedia Interface) port supports a UHD device such as an LCD
TV or monitor to allow viewing on a larger external display.
6. DisplayPorts
DisplayPort supports both external (box-to-box) and internal (laptop LCD panel) display con-
nections.
7. Power input (AC 100-240V, 50-60Hz)
Connected with power cord to mains for AC input.

ZOTAC ZBOX
8
Installing Hardware
Before installing hardware, please follow the instructions below to remove the cover of your
ZOTAC ZBOX.
1. Place the ZOTAC ZBOX upright on a at surface.
2. Locate the two thumb screws and remove.
3. Press down on the arrow of the top cover and slide and remove the top cover o󰀨 the
ZOTAC ZBOX in the direction of the arrow.

ZOTAC ZBOX
9
4. Lift and remove the two side covers.

ZOTAC ZBOX
10
Installing a graphics card (optional)
1. Remove the screw from the PCB bracket. (tool required, not included)
2. Connect the power cables to the graphics card.
*Graphics card compatibility - Power: up to 220W, Width: dual-slot, Length: 230mm / 9.06in

ZOTAC ZBOX
11
3. Insert the graphics card into the available PCIE slot.
4. Bind the cables to the small bracket with a nylon cable tie. (optional)
5. Install the screw to secure the graphics card.

ZOTAC ZBOX
12
Installing a memory module
1. Lay the ZOTAC ZBOX on a at surface with the right side upwards.
2. Gently push down on the memory retainer clips to the open position.

ZOTAC ZBOX
13
Note: This ZOTAC ZBOX accomodates two DDR4 SO-DIMM memory modules. You must install at least one module for
the system to function.
3. Insert a SO-DIMM memory module into the slot.
4. Gently push the SO-DIMM memory module down into the slot until the retainer clips lock
into place.

ZOTAC ZBOX
14
Installing M.2 SSD and Optane memory modules
There are two M.2 slots to support PCIe X4, SATA III SSD and Optance memory accordingly.
M.2 PCIe x4 SSD /
Optane memory slot
(22/42, 22/80, 22/110)
M.2 PCIe x4 /
SATAIII SSD slot
(22/42, 22/80)
This is example to install a M.2 PCIe x4 / SATA SSD module, similar steps for installing 2nd
PCIe x4 SSD or Optane memory module into another slot.
1. Remove the screw securing the hard disk bracket.

ZOTAC ZBOX
15
2. Remove the hard disk bracket.
3. Locate the M.2 PCIe x4 / SATA SSD slot and remove the screw from the screw bolt.
(tool required, not included)

ZOTAC ZBOX
16
4. Attach the screw to the M.2 PCIe x4 / SATA SSD module.
5. Insert the M.2 PCIe x4 / SATA SSD module into the slot at a 45 degree angle.
6. Gently press down on the M.2 PCIe x4 / SATA SSD module, and install the screw.

ZOTAC ZBOX
17
Installing a hard disk / SSD
1. Locate the 2.5-inch SATA hard disk / SSD and the hard disk bracket.
2. Install the hard disk / SSD to the hard disk bracket.

ZOTAC ZBOX
18
3. Insert the hard disk bracket into the SATA slot.
4. Reinstall the thumb screw.

ZOTAC ZBOX
19
Setting up your ZOTAC ZBOX
You need to connect peripherals before using your ZOTAC ZBOX.
1. Connecting a WiFi antenna module
Connect a BT/WiFi antenna module to the BT/WiFi antenna connector.
2. Connecting to a network device
Connect one end of a network cable to the LAN port on the system rear panel and the other
End to a hub or switch. The LAN port marked with K is for Killer Ethernet.
3. Connecting to USB 3.1 devices
Connect USB 3.1 devices such as external hard disk drives, SSDs and ash drives to the USB
3.1 port on the system rear panel.
1
1
23
1
4
5
6
7
5
1
22345 67