ZyXEL Communications AG-225H User manual

ZyXEL AG-225H
802.11a/b/g Wi-Fi Finder & USB Adapter
Quick Start Guide
10/2005
Version 2.1

ZyXEL AG-225H Quick Start Guide
1
Important Note
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.

ZyXEL AG-225H Quick Start Guide
2
1. Wi-Fi Finder Mode (User Interface)

ZyXEL AG-225H Quick Start Guide
3
1.1 LCM Description
Security Information
WEP security is enabled.
WPA security is enabled.
Wireless security is disabled
(no security)
Entr
y
Display the current
entry of the detected
Access Points. Users
can detect up to 15
networks at one time.
Channel
Display the radio
channel of the
detected network.
Detect Mode
Display up to 15 detected
networks in the order of the
signal strength
Display the detected networks
without any security setting
(free hot spot).
Display the dedicated network
you choose to use
SSID
The SSID identifies the Service Set
to the network users detect. When
the length of SSID is longer than 12
characters, it will be scrolled
horizontally.
Power
Display Low Battery
Display Full Battery
Signal
Indicate A/B/G World Wide Radio
Band.
5 levels of signal strength.
802.11a mode at 5 GHz band
802.11b mode at 2.4 GHz band
802.11g mode at 2.4 GHz band

ZyXEL AG-225H Quick Start Guide
4
1.2 Basic Operation
1. Power on the ZyXEL AG-225H
2. The ZyXEL AG-225H will automatically detect the available wireless
networks in 6~7 seconds.
3. The site survey information will be
displayed on the LCM including the SSID,
channel, signal strength, wireless network
protocol (IEEE802.11a/b/g), and the type
of wireless security/encryption (WEP or
WPA)
4. Push the “Next” button to see more access points you have detected.
For advanced features of the ZyXEL AG-225H, there are totally 3 modes to
choose:
Mode mode is set by default for most users to detect the Wi-Fi
networks.
Mode
(Free Mode)
Hold the “Seek” button for 1 second to switch to mode.
In mode, push the “Seek” button to detect the free hot
spots or available WLAN that you can connect to the Access
Point without any security setting.

ZyXEL AG-225H Quick Start Guide
5
Mode When you need to connect the specific Aceess Point and lock
on it, push the “Next” button to select the desired Aceess
Point. To dedicate tracking a certain AP, hold the “Seek”
button to swith to mode.
Then push “Seek” button once again to periodically do the
site survey automatically in mode. By doing so, the modes
can be changed from mode to mode.
When ZyXEL AG-225H Wi-Fi Finder is not used for 1~2 minutes, the device
will enter into the power saving mode untill you push the “Seek” button again
for searching the access points.
Charging
When low power icon appears , recharge the ZyXEL
AG-225H with your USB port on your laptop or desktop PC.
The LCM will display when the device is charging and
display when the device finishs charging.
Note: To save power, switch off the ZyXEL AG-225H when not using Wi-Fi
Finder.

ZyXEL AG-225H Quick Start Guide
6
1.3 LED Display
The following table describes the LEDs on the ZyXEL AG-225H (Wi-Fi Finder
Mode)
LED COLOR STATUS DESCRIPTION
On The ZyXEL AG-225H is power on.PWR
Blue
Off The ZyXEL AG-225H is either power off or entering
into the Power Saving Mode.
On The ZyXEL AG-225H is detecting the wireless networkLINK Blue
Off The ZyXEL AG-225H is not detecting the wireless
network.

ZyXEL AG-225H Quick Start Guide
7
1.4 Button Display
The following table describes the Buttons on the ZyXEL AG-225H (Wi-Fi Finder
Mode).
BUTTON DESCRIPTION
SEEK
Push “SEEK” to detect the wireless networks.
NEXT Push “NEXT” to see the wireless networks you detect.
Switch right to power on the ZyXEL AG-225H. OFF/ON
Switch left to power off the ZyXEL AG-225H.

ZyXEL AG-225H Quick Start Guide
8
2. Installation Requirements for Adapter Mode
Before installation, make sure you have the following requirements.
•Pentium II 300MHz or above
•A minimum of 20 MB available hard disk space
•A minimum of 64 MB RAM
•A CD-ROM drive
•A computer with an available USB port
•USB1.1 Interface (USB 2.0 strongly recommended)
•Windows XP/2000
2.1 ZyXEL Utility/Driver Setup in Adapter Mode
The installation procedures are similar for all supported Windows versions.
Windows XP screen shots are shown unless otherwise specified.
)DO NOT insert the ZyXEL AG-225H at this point.
1. Insert the support CD into the CD-ROM drive on your computer. The
installation program will automatically run. If it does not, locate and double-
click setup.exe on the support CD.

ZyXEL AG-225H Quick Start Guide
9
2. Click Install Utility to start
installation.
3. Client utility and driver will be automatically installed.
4. A welcome screen displays. Click Next.
5. Click Next to accept the default file
location or click Browse to select an
alternate folder.
6. Click Finish to complete the installation.
7. After installation is completed, a Z icon will appear in your system
tray.
8. Locate an available USB port on the computer (USB 2.0 Port Preferred).
9. Connect the ZyXEL AG-225H to your USB port via the included USB
cable.
10. The LED turns on if the ZyXEL AG-225H is properly plug in.