ZyXEL Communications P-661HW-D Series User manual

P-661HW-D Series
802.11g Wireless ADSL2+ 4-port Security Gateway
Quick Start Guide
Version 3.40
Edition 1
3/2006

P-661HW-D Series Quick Start Guide
2
Overview
Use the included CD or follow the directions in this Quick Start Guide to set up your P-661HW-D.
How to use the included CD
This CD provides multi-media animations that help you set up your P-661HW-D.
1On the included CD, click Multimedia Auto Provisioner > Installation Tutorial.
2At the end of the tutorial, click Configuration Genie.
1 Hardware Connections
1Use a telephone wire to connect your P-661HW-D’s DSL port to a telephone jack or the DSL (or modem)
jack on a splitter.
2Use an Ethernet cable to connect a computer to an ETHERNET port for Internet access.
3Use the power adaptor provided with your P-661HW-D to connect an appropriate power source to the
POWER socket. Make sure the power source is on.
4Push in the POWER button. Look at the lights on the front panel.
•ThePOWER light blinks green while your P-661HW-D starts up, and stays on once it is ready.
•TheDSL light stays on if a physical connection with the ISP is established. The INTERNET light stays on when
Internet access is available and blinks when the P-661HW-D is sending or receiving data.
• Each ETHERNET light stays on if the corresponding ETHERNET port is properly connected, and blinks when
there is traffic.
•TheWLAN light stays on if the wireless network is ready, and blinks when there is traffic.

P-661HW-D Series Quick Start Guide
3
If any of these lights are not on, check your connections, and inspect your cables for damage. If the lights are
still off, contact your local vendor.
2 Status Page
3See the User’s Guide for field descriptions of the Status screen.
1In your browser, go to http://192.168.1.1.2Enter the default password user to go directly to
the Status screen.
If your browser cannot find this screen, check its
security settings. See Troubleshooting for details.

P-661HW-D Series Quick Start Guide
4
3 Internet and Wireless Setup
1In your browser, go to http://192.168.1.1.
6Follow the directions in the wizard. Do not change default settings if your ISP did not provide information.
OTIST
ZyXEL's One-Touch Intelligent Security Technology (OTIST) feature allows you to automatically configure the
SSID and WPA-PSK on all OTIST-equipped wireless network devices within range of the P-661HW-D.
2Enter the admin password 1234 to set up your
internet and wireless connections and security
settings.
3Follow the directions in this screen. It is highly
recommended that you change the default
password.
4Click Go to Wizard setup. Then, click Apply.5Click INTERNET/WIRELESS SETUP. Wait while
your P-661HW-D tries to detect your DSL
connection.

P-661HW-D Series Quick Start Guide
5
Note: If you enable OTIST but select Disable wireless security using the wireless wizard, the P-
661HW-D will create a WPA-PSK automatically.
If you enable OTIST and select Manually assign a WEP key using the wireless wizard, the P-
661HW-D will replace the WEP key with a WPA-PSK.
Enable OTIST only if your wireless clients support WPA and OTIST.
You must enable OTIST on the P-661HW-D and all wireless clients within three minutes in any order.
To start OTIST on the P-661HW-D, hold in the RESET button (see Section 1) for one to five seconds. Do not
hold the RESET button in for too long, as this will reset the P-661HW-D to the factory defaults.
To enable OTIST on wireless clients, click Start in the Adapter screen. The Setup Key is 01234567 by
default. If you have previously saved a Setup Key on the P-661HW-D, use it instead of the default.
For more information, see Wireless LAN in the User's Guide.
Troubleshooting
If you cannot access the web configurator using Internet Explorer in Windows XP or Windows Server 2003,
make sure you allow pop-up windows, JavaScripts and Java permissions or set the Internet security level
lower than High in Internet Explorer (in Internet Explorer, Click Tools > Internet Options > Security > Custom
Level...). See the appendix in the User’s Guide for more information.
If you cannot access the Internet when your computer is connected to the ETHERNET port, follow these steps.
1Check the lights on the front panel. If they are different from what is described in section 1, make sure the
connections are correct. (See section 1.) If the lights are still different, turn off the device, wait a few
seconds, and turn it on again.
2Follow the steps in section 3again. Make sure you enter the correct information. For example, if your
account has a user name and password, make sure you type it correctly. In addition, if you are not sure
which encapsulation your ISP uses, contact your ISP.
3If you are using a new Internet account, contact your ISP to make sure it is active.
4If you still have problems, see Troubleshooting in the User’s Guide.
If you cannot access the Internet using the wireless network, follow these steps.
1On a computer in the wireless network, open your browser, and go to http://192.168.1.1. If you see the
screen in step 2of section 3, follow suggestions 1- 4above. If not, go to the next step.
2Make sure your P-661HW-D and the computers in your wireless network are using the same wireless and
security settings. Follow the steps in section 3.
3If you still have problems, see Troubleshooting in the User’s Guide.

P-661HW-D Series Quick Start Guide
6
Viewing Your Product’s Certifications
1Go to www.zyxel.com.
2Select your product from the drop-down list box on the ZyXEL home page to go to that product's page.
3Select the certification you wish to view from this page.