ZyXEL Communications Unified Security Gateway ZyWALL 300 User manual

www.zyxel.com
Unified Security Gateway
Firmware v2.11
Edition 1, 11/2008
QUICK START GUIDE
ZyWALL USG 300
DEFAULT LOGIN DETAILS
IP Address: https://192.168.1.1
Username: admin
Password: 1234
CONTENTS
ENGLISH 3
DEUTSCH 17
ESPAÑOL 33
FRANÇAIS 47
ITALIANO 61
РУССКИЙ 89
简体中文 103
繁體中文 115
Copyright 2008 ZyXEL Communications Corporation
C

2
Front and Rear Panels
SYS CARD 1-2
PWR AUX
USB 1-2
P1 - P7
EXTENSION
CARD SLOT 2
POWER
AUX CONSOLE
SOCKET
EXTENSION
CARD SLOT 1
RESET

ENGLISH
3
ENGLISH
Checking the Package Contents
Your package should include one of each of the following:
• ZyWALL USG
300
• Power cord
• Rack-mounting
kit
• RJ-45 Ethernet cable
• RS-232 console Y-
cable
• Printed Quick Start
Guide
• Configuration
Reference
Card
• Compact disk
(CD)

4
Rack-mounted Installation
Mount the ZyWALL in a 19-inch rack or place it on a sturdy, flat surface.
Leave 10 cm of clearance at the sides and 20 cm in the rear.
1. Align one bracket with the holes on one side of the ZyWALL and
secure it with the included bracket screws. Similarly, attach the other
bracket.
2. After attaching both mounting brackets, position the ZyWALL in the
rack by lining up the holes in the brackets with the appropriate holes
on the rack. Secure the ZyWALL to the rack with the rack-mounting
screws.

ENGLISH
5
Connecting the Hardware
Make sure that the power switch on the rear panel is turned off before
you make the hardware connections.
1. It is recommended that you configure the ZyWALL before using it to
protect your network. Use an Ethernet cable to connect a computer to
port 1.
2. Use another Ethernet cable(s) to connect port 2 and/or port 3to an
Ethernet jack with Internet access.
3. Use the included power cord to connect the power socket on the rear
panel to a power outlet.

6
4. Push the power switch to the on position and look at the front panel.
The PWR light turns on. The SYS light blinks during system testing
and initialization and then stays on when the system is ready.

ENGLISH
7
Web Login
1. Launch your web browser
and go to http://192.168.1.1
(the ZyWALL automatically
redirects you to https://
192.168.1.1).
2. Click Yes to proceed if
you get a security alert
or certificate screen.

8
3. Enter admin as
the user name
and 1234 as the
password. Click
Login.
4. It is strongly recommended
that you change the
password. Type and retype
a new password, and click
Apply.

ENGLISH
9
Installation Setup Wizard
Use an installation setup wizard to connect to the Internet and register
the ZyWALL and/or activate trial services, like IDP and content filter.
Use the installation wizard only for initial configuration starting
from the default configuration.
The Status screen opens. Click the Wizard icon in the upper right
corner.

10
Changes you make in the installation wizard may not be applied if you
have already changed the ZyWALL’s configuration.
• INSTALLATION
SETUP, ONE ISP
sets up a single
Internet
connection for
ge2.
• INSTALLATION SETUP, TWO ISP sets up Internet connections for
ge2 and ge3.
The wizard screens vary
depending on the
encapsulation type you
use. Refer to
information provided by
your ISP and the web
help screens to know
what to enter in each
field. You can leave
fields blank if you don’t
have that information.