ZyXEL Communications LTE7485-S905 User manual

LTE7485-S905
4G LTE-A Outdoor Router
Copyright © 2020 Zyxel Communications Corp. All Rights Reserved.
See the User's Guide at www.zyxel.com for more information,
including customer support and safety warnings.
Quick Start Guide
1/4
US Importer
Zyxel Communications, Inc
1130 North Miller Street Anaheim, CA 92806-2001
https://www.zyxel.com/us/en/
1 2
Make sure the LTE7485-S905 is turned off. There should be no Ethernet cable connected
providing power using PoE. Unscrew the SIM card slot cover and remove it.
1Gently place a SIM card into the SIM card slot until it clicks into place. 2
Step 1 SIM Card Installation
Cat 5e
Power Injector
Power Outlet
Pole Mounting
Cat 5e
Power Injector
Power Outlet
Wall Mounting
Gateway
LaptopSmartphone PC
Place the LTE7485-S905 in an open
area free of obstacles, and adjust the
angle to point it towards the base
station to have the strongest possible
LTE signal.
LAN (PoE)
LOCK
1 2 3 4
Follow steps 1 to 4 in the drawing to connect an 8-pin Cat 5e Ethernet cable to the LTE7485-S905's LAN port.
1-4
Step 2 Cable Connections
Location Examples
Package Contents
LTE7485-S905 Cable
Gland
Quick Start
Guide
Safety
Warnings
Grounding
Wire
GbE
Cable
Gigabit
PoE Injector
M8 Hex Bolt
(1.25*120mm)
x1
M6 Hex
Nuts
x6
Nylon Wall
Plugs
x4
Tapping Screws
M4x25 mm
x4
x2
M8 Screws
M6 Washers
x6
M8 Washers
x3 x3
M8 Spring
Washers
x6
M6 Spring
Washers
Mounting Kit
Main Frame
x1
U-Type
Screws
x2
Bracket-1
x1
M Bracket
x1

2/4
PoE injector
Power outlet
LAN PoE
1
2
34
Step 3 Cable Connections
Connect the Ethernet cable to the included PoE injector PoE port.
Connect the LAN port of the injector to a computer or a router with the included Ethernet
cable.
1
2
Connect the power plug on the PoE injector to a power outlet.
Check the LED next to the SIM card slot.
3
4
RESET SI M
LAN (PoE)
Red
Green Blinking - Connecting to the Internet
Steady - Connected to the Internet
Blinking - Booting
Steady - Error
Step 4 Connecting WiFi to Your LTE7485-S905 for Easy Setup
RESET SI M
1
Amber Blinking - WiFi is on
3
Check if WiFi is on - the amber LED is blinking. If not, press the WiFi button to enable WiFi.
Scan the WiFi QR code on the device label then follow the prompts to connect to the WLAN on
your mobile device.
You can download the LTE Ally app or use the web configurator (see next) to manage the
LTE7485-S905.
1
2
3
4
5
Remove the label from the back of the LTE7485-S905 and put it on the injector. Scan the Login
QR
code to use the default username and password to log in the LTE Ally app for the first time.
Screw the SIM card slot cover back into place.
Login Password
User Name
First-time login please find Username
and Password on device label.
admin
or
Scan QR code to login quickly
LTE Ally
Log in
Forgot password?
xxxxxxxxxx
Login
Login a ddress : 192.168.1.1
User Name : admin
Login Password : XXXXXXXXXX
PoE injector
5
2
4
WiFi
WiFi
RESET SI M
LAN (PoE)
Cancel
LTE Ally
LAN PoE
https://192.168.1.1
User Name: admin
Login Password: XXXXXXXXXX
LTE7485-S905
User Name
Password
Login
XXXXXXXXXX
admin
https://192.168.1.1
Open a web browser and go to https://192.168.1.1.
Enter the default username (admin) and password (see label), and then click Login.
See the User’s Guide at www.zyxel.com for more information.
Configuring Your LTE7485-S905 (Optional)

3/4
Wall Mounting (Optional)
Use washers, spring washers, and nuts to attach the M-type bracket to the back of the
LTE7485-S905.
Follow steps 4-5 in the drawing to align the rotating bracket with the M-type bracket, insert the
M8 bolt through the holes, and use washers and spring washers to secure it.
Follow steps 2-3 in the drawing to attach the rotating bracket to the mounting main frame
using washers, spring washers, and hex nuts. Do not tighten the nuts until you adjust the
mounting angle in the final step.
1
32
Spring Washers
x2
M6 Hex NutsM Bracket Bracket-1
Main Frame
x2
x2x1
x1
x1
Washers
M8 Spring Washers
x2
M8 Screws
x2
x2
M8 Washers
M8 bolt
x1
-
12
345
5-4
x4
Unit: mm
25.4
8.0 1
3
96mm
96mm
2
Four Nylon Wall Plugs
Use the four corner holes of the M bracket to mark holes on a wall. Drill four holes in a wall.
1 2 Insert the screw anchors and screws into the holes.
M4 Screws
Unit: mm
x4
25.4
4.0
2.38
9
Insert nylon wall plugs into the wall. Use mounting screws to secure the main frame to the wall
through the nylon plugs.
3
Step 5 Pole / Wall Mounting: Connect M Bracket and Main Frame

4/4
Pole Mounting (Optional)
M6 Spring Washers
U-Type Screws
x2
x4
M6 Washers
x4
M6 Hex Nuts
x4
Place the U-bolt around a pole. Insert the U-bolt into the holes on the main frame. Use a wrench
to secure the main frame to the pole with the washers, spring washers, and nuts.
1
Step 6 Pole / Wall Mounting Angle Adjustment
-40°
horizontal
+40°
+0°
horizontal
45°
vertical
-48°
vertical
Connect the PoE injector to a power outlet. Use the LTE Ally app to find the optimal LTE signal strength and manage your LTE7485-S905.
Note: After configuring the LTE7485-S905, turn WiFi off.
Safety Warnings
Humid、dusty and extreme environment in which place the product and obstructing the device ventilation
slots are prohibited, any kind of conditions above may harm your device.
There is a remote risk of electric shock from lightning.
do not install, use, or service this device during a thunderstorm.
Connect only suitable accessories to the device; make sure to connect the cables to the correct ports.
Do not open the device, opening or removing covers can expose you to dangerous high voltage points or
other risks. Please contact your vendor for further information.
Place connecting cables carefully so that no one will step on them or stumble over them and disconnect all
cables from this device before servicing or disassembling.
Please use the provided or designated connection cables/power cables/ adaptors. connect it to the right
supply voltage (for example, 110V AC in North America or 230V AC in Europe), If the power adaptor or cord
is damaged, it might cause electrocution. remove it from the device and the power source , repairing the
power adapter or cord is prohibited , Contact your local vendor to order a new one.
Risk of explosion if battery is replaced by an incorrect type, dispose of used batteries according to the
instruction.
Please refer to the device back label, datasheet or box specifications catalog information for rated power
of device and operating temperature.
The socket-outlet shall be installed near the device, and shall be easily accessible because it serves as the
main disconnecting device.
Disposal and Recycling Information
The symbol below means that according to local regulations your product and/or its battery
shall be disposed of separately from domestic waste. If this product is end of life, take it to a
recycling station designated by local authorities. At the time of disposal, the separate collection of
your product and/or its battery will help save natural resources and ensure that the environment
is sustainable development.
Secure a green/yellow ground cable (18 AWG or smaller) to the LTE7485-S905’s rear panel using the M4 ground screw. Attach the
other end of the cable to the ground, either to the same ground electrode as the pole you installed the device on or to the main
grounding electrode of the building. Follow your country’s regulations and safety instructions to electrically ground the device
properly. Qualified service personnel must confirm that the building’s protective earthing terminal is valid.
Step 7 Grounding