1Zpresso Kpro Series User manual

1Portable
Manual
Grinder
Kpro/Kplus
Series

Guide
HfandBall
Crank Handle
3
Stamess Steei
Top Bearing Cover
371.4
Stalnless Steel
Scale Ring
ALLmJInumAIon
Anti—slip Leather
1'Thel!.‘ustrateisfor
reference onlyto
hve in kind a5 the
standard)
Central Shaft
304 Stainless Steel
Burr
Tltanium Stainless
Steel (The
colorof
burr isforreference
only to live in kind
asthe standard
Powder Hammer
Aluminum Alloy
Powder '
Receiver
Aluminum Alloy
Bottomless ----------------
4
Bottom
x
Aluminum Alloy
Bottom
Aluminum Alloy
B
.....ai....I b
5 I
_1
Knurled Thumb Nut
304 Stainless Steel
Top Bearing
Bearing Steel
Main Body
Aluminum Alloy
--Burr Ring Holder
for Plus
Aluminum Alloy+
Magnetic
Lower Bearing Cover
AIuminumAIloy
Spring
304 Stainless
Steel
Lower MagneticRing
Aluminum Alloy+
Magnetic
Burr Ring
Holder for
Pro
Aluminum
Alloy
T!
Receiver
Aluminum
Alloy
1V"
K"
The capacity of powder
receiver:35-409
(according to beans type)
Instructions
Scale Ring Red Dot
.Turn the grinding dial clockwise, the Red Dot points t0 the
number is your grinding degree.Turn t0 the Iarger number to
set the coarser particle; the smaller number to set the finer
particle.
.There have 90 clicks in a circle, the pitch is 2mm,
0.022mm/click, it able to turn 1.5 circles.
. When reassembled, calibrate
the Scale Ring
correctly
befäom’f'“
. Please refer to the grinding recommendation
card
for different brewing methods.
5. Rotate the handle clockwise t0 start grinding.
Please watch the video on our web (or scan the QR Code‘):fot’„‚m“
disassemblelassemble the grinder.
https:llwww.1zpresso.com
YouTube official channel

an.
l
_
„,9.
442.1":
A
.21
39.121
2a}
:.‚.‚
How
to
Assemble
How to Disassemble
illlustrate
for K-Plus
Grinder)
2*: Not remove the Burr Ring Holder before step 3.
‚Il«
_ _ ä—m
1. Duetothe ring inverse design,
i Turnthe Scale Ring clockwrse
f z ß- please screwthe
ScaleRing
maxnnizethegapofScaIe Ring 7
\ counter-clockwise tightest.
a ‚i:
<---
„ 2. Turn the Scale Ring clockw‚lsc_‚___p
i x x;
Rim‘
m".
“7L!
as an Illustration
as an Illustration
2 Lift the bottom cutter head.
screw the Knurled Thumb Nut
counterclockwise,
take offthe
Top Bearing Cover/ Top Bearing.
3. Screw the Burr Ring
Hold
tightly counterclockwise‘
.Take off the Shaft/ Lower
Bearing
Cover / Spring in order.
4. Install Spring (small-dl
facing the burr)/ Lower
Cover (convex
surfac
'
‚Due to the ring inverse design,
please lose and remove the Burr
Ring Holer and Scale Ring
clockwise.
— 5. DO NOT clean with water, use i gk
brush and blower to clean parts. ; 6. Install Top Bearing
(concave dots facing
top of the Scale Ring.
DO NOT disassemble the following components
7. Push the bottom
o "
the Knurled Thu
clockwise
into tig
8. Calibrate is nece
l»
please follow
the
last page.
Central shaft Burr ring holder Scale Ring Bearing
and burr

Howto Calibrate
PrI'nCI'pIe.'
’ ’lw;
‚Umducl r.‚orr:‚oletes tr'ie caiioration b/ retracvng
the Knx ac
Thumb Nut
and the Scale Ring to adjust. bring into
anrrespondence
Nlth the Central shaft. the innerlouter
Burr
cir 3e the Red
Dot pounts at
2 ll was normal that
there have range between 2
clicks man
calibration lo "zer'o"
due to the ring locking
force cannot De
unlfied.
Illustrates
1. Calibrate
correctly With the followi'ng
conditions
afterAssemble:
0 Red Dot points at
”0'
0 The
Central Shaft is not Ioose
o The
inner/outer Burr close
2. The Red
Dot points at the right side of "0":
Turn
the Scale Ring clockwise to the end.
unscrew the
Knurled Thumb Nut a .‘ittle bit. Lau)
6‘
ä ‘ j ‚ . turn the Scale Ring
anti-clockwise bacx‘ t0
" k . 1 ‚ tightestRepeat the steps until Calibrate
correctly.
3. The Red Dot points at the left side of “0":
Turn the Scale Ring clockwise to the end.
screw the Knurled Thumb Nut a Iittie bit
VW. tighter. turn the
Scale Ring
anti-clockm’se
L ' ; ‘ „ backtotightestRepeatthe steps untii
Calibrate correctly.
Precautions
o DO NOT clean grinderwith water.
0 Keep
it in dry condition.
0 Please follow the instructions procedures of disassembiy and
assembly.
0 DO
NOT Iet children use this device for
safety.