2E mechatronic 6220312 User manual

Instruction Manual
Specication 6220312
Inclination Sensor with analog output (4-20mA)
2E mechatronic GmbH&Co.KG
Maria-Merian-Str. 29
D-73230 Kirchheim/Teck
Phone [phone]
Fax [phone]
Mail [email protected]
Web www.2E-mechatronic.de
stephan huttenlocher
Produktmanager/Product Manager
2E mechatronic GmbH & Co. KG
Mikrosysteme für die Industrie
Maria-Merian-Straße 29, D-73230 Kirchheim/T.
Tel.: [phone], Fax: -70
E-Mail: [email protected]
www.2e-mechatronic.de
narr group
2E VK 08-12-RZ 27.09.12 16:02 Seite 6

Contents
Specication 6220312 ...........1
Declaration of Conformity ........3
CE-Conformity ...............3
General .....................3
Technical Data ................4
Installation/Assembly .........4-5
Safety Instructions .............6
Electrical Connector ............6
Operation ...................7
Service .....................8
Page 2 | Instruction Manual 6220312 | 2E mechatronic

Declaration of Conformity
CE-Conformity
This product has been developed and manufactured in accordance with the
current European standards and guidelines.
Note: A Declaration of Conformity can be requested separately.
General
The Inclination Sensor 6220312 is an instrument used to control the inclination
angle of a reference axis.
The product should be examined for any possible damage that may have
occurred during transportation. Should any damage have occurred, please
contact the transportation company or 2E mechatronic without delay.
Read the instructions carefully. Familiarize yourself with the device before as-
sembling, installing and operating.
The following assembly and operation instructions have been carefully drafted,
however, it is not possible to cover every conceivable eventuality. Therefore, if
you have any queries regarding the product or its application we can be con-
tacted at our internet address (www.2E-mechatronic.de) or one of our contact
personnel for further information.
The Sensor should be operated and installed in accordance with the instruc-
tions given in order to guarantee that the device and the connected systems
operate safely.
The safety of operating personnel can only be guaranteed when the device is
used for the purpose which it was intended for.
Furthermore the national regulations are to be followed. (e.g. VDE0100)
Only shielded cables have to be used for connecting the device.
Page 2 | Instruction Manual 6220312 | 2E mechatronic Page 3 | Instruction Manual 6220312 | 2E mechatronic Page 4 | Instruction Manual 6220312 | 2E mechatronic

Page 3 | Instruction Manual 6220312 | 2E mechatronic
RT = Room temperature 23°C ±5K
FS = Full scale (360°)
This is a Protection Class IP67 device.
Installation/Assembly
The Sensor can be mounted on the target unit in 2 ways, both perpendicular
and parallel to the axis rotation.
Variation 1 (Perpendicular to axis): First, ensure that the surface is clean.
Then, mount the Sensor using 2 at head screws (max. Ø4.5mm thread
diameter) to the target unit.
Variation 2 (Parallel to axis) mount the Sensor using 2 head shoulder screws
(tting an inner diameter of Ø5H7).
Page 4 | Instruction Manual 6220312 | 2E mechatronic
Technical Data
Axis 1
Positive sense of rotation Clockwise
Measurement range (angle) 360° (or custom spezific)
Resolution 14 bit (0,022° FS)
Dimensions 79 mm x 28 mm x 21 mm
Operating voltage 10V....30V
Measurement rate < 180 ms
Protection class IP67
Temperature range
(operating and storage)
-40°C bis +85°C
Weight 80g (with cable/connector)
Accuracy (RT) ±0,1% FS
0,1° (
Measurement range <100° )
Temperature dependence ±0,1%/10K
Housing Aluminium, 2 xings
Interface analog, 4-20mA
Output 3,8-20,2mA (error 1mA)

Page 6 | Instruction Manual 6220312 | 2E mechatronic Page 5 | Instruction Manual 6220312 | 2E mechatronic
Fixing Point Variation 2
Fixing Point Variation 1

Electrical Connector
Sensor-/Actor-Panel Connector 4 pol. M8
IEC 61076-2-104
Voltage requirements: 10–30 V DC
Power Consumption at 10-30V DC: 32mA
Description of all input and output ports/terminals
Page 6 | Instruction Manual 6220312 | 2E mechatronic
Variations Pin 1 Pin 2 Pin 3 Pin 4
6220312
kNS Standard analog
brown
VCC (+)
white
COM
blue
GND
black
I-SIG out
Safety Instructions
Responsibility for safe planning, assembly, operating and maintenance lies
with the equipment user.
The installation and operation of all devices should only be carried out
by qualied personnel. Changes or modications which are not expressly
approved in the operation manual and are made without permission could
void the warranty and manufacturer’s liability. Should a severe disturbance
occur, the device should be taken out of operation immediately and pro-
tected against accidental reuse. If such an occurrence should happen the
device should be sent to 2E mechatronic for repair.

Page 7 | Instruction Manual 6220312 | 2E mechatronic
Output signal
[mA]
Inclination
Default settings
[°]
Inclination
customer specific
[°]
4 0
Measuring range min
20 360 Measuring range max
1 Error Error
Operation
The Sensor comes with an analogue current-interface (4-20mA)
Connect Pin 1 with Vcc and Pin 3 with GND.
COM (PIN 2) is either not connected (n/c) or connected with PIN1.
Between I-SIG out (Pin 4) and GND (Pin 3) the output signal can be
measured.
The current limits for the output signal are 3,8mA and 20,2mA
(apart case of error).
In case of error check rst the pin conguration.
Supply Voltage apparent ohmic resistance
Generally
9V 100Ω
12V 250Ω
24V 500Ω

Page 7 | Instruction Manual 6220312 | 2E mechatronic Page 8 | Instruction Manual 6220312 | 2E mechatronic
Service
The Sensor is maintenance free.
Should a fault occur please contact the following:
2E mechatronic GmbH&Co.KG
Maria-Merian-Str. 29
D-73230 Kirchheim/Teck
Phone [phone]
Fax [phone]
Mail [email protected]
Web www.2E-mechatronic.de
16.10.2013