Panasonic HG-T Series User manual

Thru-Beam Type Digital Displacement Sensor
HG-T series
User’s Manual
WUME-HGT-6
2020.11 panasonic.net/id/pidsx/global

(MEMO)
2 WUME-HGT-6

Introduction
Thank you for purchasing an HG-T series thru-beam digital displacement sensor.
Before using this product, read and understand this User's Manual. Use the product correctly
and in the optimum manner.
Keep this manual in a safe location for reference whenever necessary.
Types of Manuals
The following user’s manuals are available for the HG-T series. Refer to the appropriate manual
according to your need.
The user’s manuals are also available for download from our website (https://panasonic.net/id/
pidsx/global).
Unit name or purpose of
use Manual name Manual code
HG-T Control Unit HG-T User’s Manual WUME-HGTM
HG-T Configuration Tool HG-T Configuration Tool User’s Manual WUME-HGTCT
Please note
1. No part of this manual may be reproduced or reprinted in any form or by any means without prior written
permission from Panasonic.
2. The contents of this manual are subject to change without notice for future improvement.
3. This manual has undergone strict quality control; but should you discover any dubious information,
mistakes, misplaced pages, or missing pages, please contact your local dealer.
WUME-HGT-6 iii

Manual Configuration
Chapter 1 Before Using This Product
This chapter explains safety and handling precautions, laser
safety standards, and other information that should be
checked before using this product.
Chapter 2 System Configuration This chapter explains the system configuration.
Chapter 3 Overview of HG-T Series This chapter explains the principle of measurement and how
to use this product when controllers are connected.
Chapter 4 Installation and Connections This chapter explains installation, connections, wiring, and
other work.
Chapter 5 Basic Usage
This chapter explains the flow of operations up to
measurement startup, the base screen displayed when the
power is turned ON, and basic operations.
Chapter 6 Setting up General Functions This chapter explains details and settings for general
functions.
Chapter 7 Setting up Extended Functions This chapter explains details and settings for extended
functions.
Chapter 8 Specifications and Dimensions This chapter explains the specifications and dimensions.
Chapter 9 Maintenance This chapter explains maintenance and inspection.
Chapter 10 Troubleshooting This chapter explains troubleshooting and error codes.
Chapter 11 Appendix This chapter provides menu structure.
Product Version
This manual has been created based on the product functions available as of November 2020.
For product version information, refer to "1.6 Product Version and Functions".
iv WUME-HGT-6

Table of Contents
1 Before Using This Product...................................................................1-1
1.1 Safety Precautions (Always observe) .................................................1-2
1.2 Handling Precautions..........................................................................1-3
1.3 Laser Safety Standards ......................................................................1-5
1.3.1 IEC / JIS / GB................................................................................... 1-5
1.3.2 FDA.................................................................................................. 1-6
1.4 Terminology.........................................................................................1-9
1.5 Contents of Package...........................................................................1-10
1.6 Product Version and Functions...........................................................1-12
2 System Configuration...........................................................................2-1
2.1 System Configuration..........................................................................2-2
2.2 Description of Parts.............................................................................2-3
2.2.1 Controller ......................................................................................... 2-3
2.2.2 Sensor head..................................................................................... 2-5
2.2.3 Sensor Head Connection Cable ...................................................... 2-6
2.2.4 Side View Attachment...................................................................... 2-6
3 Overview of HG-T Series ......................................................................3-1
3.1 Principle of Measurement ...................................................................3-2
3.2 Role of Controllers ..............................................................................3-3
3.3 Using Connected Controllers..............................................................3-4
4 Installation and Connections...............................................................4-1
4.1 Mounting the Controller.......................................................................4-2
4.1.1 Mounting on a DIN Rail.................................................................... 4-2
4.1.2 Removing from a DIN Rail ............................................................... 4-2
4.1.3 Controller Wiring Connection Diagrams........................................... 4-3
4.2 Attaching the Sensor Head.................................................................4-4
4.3 Connecting the Sensor Head Connection Cable ................................4-5
4.3.1 Connecting to the Sensor Head....................................................... 4-5
4.3.2 Disconnecting from the Sensor Head .............................................. 4-6
4.3.3 Connecting to the Controller ............................................................ 4-6
4.3.4 Disconnecting from the Controller.................................................... 4-7
4.3.5 Connecting and Disconnecting to / from Controller Connector........ 4-7
4.4 Connecting Controllers .......................................................................4-10
4.4.1 How to Connect ............................................................................... 4-11
4.4.2 How to Remove ............................................................................... 4-13
4.5 Mounting the Side View Attachment...................................................4-14
5 Basic Usage...........................................................................................5-1
5.1 Using the Base Screen .......................................................................5-2
5.1.1 Functions of Operation Pad and Display Unit .................................. 5-2
WUME-HGT-6 v

5.2 Flow of Operations up to Measurement Startup .................................5-6
5.3 Explanation of Basic Operation...........................................................5-8
5.3.1 Checking the Beam Axis.................................................................. 5-8
5.3.2 Adjusting the Beam Axis .................................................................. 5-9
5.3.3 Reference Waveform Registration ................................................... 5-14
5.3.4 Teaching........................................................................................... 5-16
5.4 Operation Mode ..................................................................................5-22
5.4.1 Auto Edge Detection Mode ( ) ............................................ 5-22
5.4.2 Edge Detection Mode ( ).......................................................... 5-23
5.4.3 Outer diameter/Width Detection Mode ( ) ............................. 5-24
5.4.4 Inner Diameter/Gap Detection Mode ( ) ................................ 5-25
5.4.5 Central Position Detection Mode ( ).................................... 5-25
5.4.6 User Assigned Edge Detection Mode ( ) ........................... 5-27
5.5 Settings on the Base Screen (Using Shortcut Keys) ..........................5-30
5.5.1 Display Switching Mode................................................................... 5-30
5.5.2 Preset............................................................................................... 5-33
5.5.3 Saving and Loading Settings to / from Banks .................................. 5-35
5.5.4 Key Lock .......................................................................................... 5-38
5.5.5 Sensitivity Settings........................................................................... 5-40
5.6 Self-monitoring Function.....................................................................5-47
5.6.1 Using the Self-monitoring Function.................................................. 5-47
5.6.2 Statuses and Measures ................................................................... 5-48
6 Setting up General Functions..............................................................6-1
6.1 Flow of Measurement Data.................................................................6-2
6.2 Setting Operation List .........................................................................6-4
6.3 Detection Settings ( ) ..............................................................6-9
6.3.1 Operation Mode ( ) ............................................................... 6-9
6.3.2 Measurement Direction ( ).................................................... 6-10
6.3.3 Average Count (Response Time)( )........................................ 6-11
6.4 Basic Settings ( ).......................................................................6-14
6.4.1 HIGH Set Value ( ).................................................................. 6-14
6.4.2 LOW Set Value ( )................................................................... 6-15
6.4.3 Hysteresis ( ) ........................................................................ 6-17
6.4.4 Teaching Types ( ) .................................................................. 6-20
6.4.5 Tolerance <±> ( ) ................................................................... 6-21
6.4.6 Preset Value ( ) ....................................................................... 6-22
6.4.7 Preset Data Selection ( ) ........................................................ 6-23
6.4.8 Preset Save ( ) ..................................................................... 6-24
6.4.9 Reference Waveform Save ( ).............................................. 6-25
6.4.10 Output Operation ( ) ........................................................... 6-26
6.4.11 Analog Output Selection ( ) ................................................ 6-27
6.4.12 Menu Display Settings ( ) ....................................................... 6-28
6.5 Initialization ( )...........................................................................6-30
vi WUME-HGT-6

6.6 Maintenance ( ).......................................................................6-31
7 Setting up Extended Functions ...........................................................7-1
7.1 Setting Operation List .........................................................................7-3
7.2 Advanced Settings ( ) .............................................................7-9
7.2.1 Hold Settings ( )........................................................................ 7-9
7.2.2 Simultaneous Input ( )(For Master Units Only)..................... 7-17
7.2.3 External Inputs ( ) ................................................................... 7-19
7.2.4 External Outputs ( ) .............................................................. 7-21
7.2.5 External Output Delay Timer Selection ( )............................ 7-28
7.2.6 Number of Digits Displayed ( )................................................ 7-35
7.2.7 Analog Scaling ( )................................................................. 7-36
7.2.8 Eco Mode ( )............................................................................. 7-41
7.2.9 Alarm Settings ( ).................................................................... 7-42
7.2.10 Key Lock Function Selection ( ) ......................................... 7-47
7.2.11 Interference Prevention Function ( )(For Master Units
Only) ................................................................................................. 7-48
7.2.12 Sampling Cycle ( ).............................................................. 7-50
7.2.13 Reverse of Measured Value ( )........................................... 7-51
7.3 Calculation Settings ( )(For Master Units Only)...........................7-53
7.3.1 Calculation Mode ( ).................................................................. 7-53
7.3.2 Calculation Application Selection ( )....................................... 7-54
7.4 Copy Settings ( ) .........................................................................7-59
7.4.1 Copy Individual Selection ( )(For Master Units Only) ........... 7-59
7.4.2 Copy Batch Selection ( )(For Master Units Only) ................. 7-62
7.4.3 Copy Execution ( )(For Master Units Only) .......................... 7-62
7.4.4 Copy Lock ( )(For Slave Units Only) ......................................... 7-63
7.5 Bank Settings ( ) ..........................................................................7-65
7.5.1 Bank Save Selection ( )........................................................ 7-65
7.6 Calibration Settings ( ) ..............................................................7-67
7.6.1 Calibration Selection ( )........................................................ 7-67
7.7 Tab Cancellation Function...................................................................7-71
7.7.1 Setting up the Functions .................................................................. 7-71
7.7.2 Operations when the Tab is Detected .............................................. 7-73
7.7.3 Response Time when the Tab Cancellation Function Is Enabled .... 7-73
7.7.4 Checking the Hold Status ................................................................ 7-74
7.7.5 Precautions when Using the Tab Cancellation Function.................. 7-75
8 Specifications and Dimensions...........................................................8-1
8.1 Specifications......................................................................................8-2
8.1.1 Controller ......................................................................................... 8-2
8.1.2 Sensor Head .................................................................................... 8-9
8.2 Dimension Drawings...........................................................................8-11
8.2.1 Controller ......................................................................................... 8-11
8.2.2 Sensor Head .................................................................................... 8-13
WUME-HGT-6 vii

8.2.3 Side View Attachment...................................................................... 8-14
9 Maintenance ..........................................................................................9-1
9.1 Maintenance and Inspection...............................................................9-2
9.1.1 Maintenance Precautions ................................................................ 9-2
9.1.2 Main Inspection Items ...................................................................... 9-2
10 Troubleshooting..................................................................................10-1
10.1 Troubleshooting ................................................................................10-2
10.2 Error Messages.................................................................................10-5
Appendix Appendix ................................................................................App-1
Menu Structure (General Function Display)...............................................App-2
Menu Structure (Extended Function Display) ............................................App-4
viii WUME-HGT-6

1 Before Using This Product
1.1 Safety Precautions (Always observe) .................................................1-2
1.2 Handling Precautions..........................................................................1-3
1.3 Laser Safety Standards ......................................................................1-5
1.3.1 IEC / JIS / GB................................................................................... 1-5
1.3.2 FDA.................................................................................................. 1-6
1.4 Terminology.........................................................................................1-9
1.5 Contents of Package...........................................................................1-10
1.6 Product Version and Functions...........................................................1-12
WUME-HGT-6 1-1

1.1 Safety Precautions (Always observe)
This section explains important rules that must be observed to prevent personal injury and
property damage.
■Safety precautions items are classified into “WARNING” and “CAUTION”
depending on the level of hazard.
Risk of death or serious injury.
Risk of minor injury or property damage.
● Never use this product as a sensing device for personnel protection.
● For sensing devices for personal protection, use products that conform to the laws and
standards related to personal protection in each country, such as OSHA, ANSI, and IEC.
● This product is designed to inspect (judge or measure) objects and so must not be used
to ensure safety, for example, to prevent accidents that affect human lives or property.
● Do not look at or touch direct laser beams or other reflections of light, as doing so is
dangerous.
● For the controller DC power supply, only use a power supply that is isolated by means of
an isolation transformer or otherwise.
● There is a risk of short-circuiting and damage to the controller or power supply if a
transformer such as an autotransformer is used. There is a risk of short-circuiting and
damage to the controller or power supply if the controller is incorrectly mounted or
connected.
● The HG-TC series controller is designed to be used with the HG-T series special-purpose
sensor head to satisfy the specifications. If the controller is used with any sensor head
other than the special-purpose sensor head, the specifications will not be satisfied and
malfunctioning or another problem may occur.
1.1 Safety Precautions (Always observe)
1-2 WUME-HGT-6

1.2 Handling Precautions
■In this manual, the following symbols are used to indicate safety information that
must be observed.
Indicates an action that is prohibited or a matter that requires caution.
Indicates an action that must be taken.
Indicates supplemental information.
Indicates details about the subject in question or information useful to remember.
Indicates operation procedures.
■Handling precautions
Specifications
● This product has been developed / produced for industrial use only.
● This product (controller and sensor head receiver) uses an EEPROM.
The EEPROM has a service life of one million setting operations.
● Do not use this product outside the range of the specifications. Risk of an accident and
product damage.
There is also a risk of a noticeable reduction of service life.
Power supply
● Verify that the supply voltage fluctuations are within the rating.
● If power is supplied from a commercial switching regulator, ensure that the frame ground
(F.G.) terminal of the power supply is connected to an actual ground.
● Do not use during the initial transient time after the power supply is switched ON.
● To ensure performance, use the product at least 30 minutes (warm-up time) after the power
is turned ON.
Wiring
● Make sure that the power is OFF before performing wiring or connection work for the
controller.
● Note that there is a risk of damage or burning if the load is short-circuited or incorrectly
wired.
● After wiring is completed, check the wiring carefully before turning ON the power.
● Do not wire the controller in parallel with a high-voltage line or power line or use the same
conduit as these lines. Doing so may result in malfunctioning due to induction.
● Do not apply stress such as excessive bending or pulling to the extracted part of a cable,
● When connecting the sensor head connection cable to this product, do not apply force to
the product.
Usage environment
● This product is suitable for indoor use only.
● The light emitting and receiving surfaces of the sensor head must be free of water, oil,
fingerprints, and other substances that refract light as well as dust, grit, and other objects
that intercept light.
1.2 Handling Precautions
WUME-HGT-6 1-3

If stains or dirt become attached to the sensor head surfaces, wipe them with a lint-free soft
cloth or lens cleaning paper. If the surfaces are very dirty, wipe off dirt using a cotton swab
(or similar material) moistened with absolute alcohol.
● Do not allow ambient light such as sunlight to directly hit the light receiving section of the
sensor head. In particular, if precision is required, use this product by mounting a douser (or
similar material) on the sensor head.
● When a measured object with a strong specular reflection component (such as glass or
specular reflector) is detected, it may not be detected correctly due to the influences of light
reflected from the measured object. In such a case, install a pair of emitter and receiver at a
certain angle so that reflected light does not hit the emitter or receiver. After adjusting the
angle, always check the beam axis. After checking the beam axis, if the beam axis is
aligned, register the reference waveform. If the beam axis is misaligned, readjust the beam
axis, and register the reference waveform.
● Avoid using this product in environments where condensation occurs due to sudden
temperature change.
● Avoid dust, dirt, and steam.
● Avoid using the product in atmospheres that contain corrosive or other harmful gases.
● Ensure that the product does not come into contact with organic solvents such as thinner.
● Ensure that the product does not come into contact with strong acid or alkaline.
● Ensure that the product does not come into contact with oil or grease.
● This product cannot be used in an environment that contains flammable or explosive gases.
● Performance may not be satisfactory in a strong electromagnetic field.
● Do not use this product in locations subject to severe vibration or shock.
● This product is a precision device. Do not drop or otherwise subject to shock. Risk of
product damage.
● Take care not to touch any terminals in the connector or allow foreign objects to enter the
connector.
● The sensor head is watertight, but the connectors are not structurally resistant to dust,
water or corrosion. Therefore, the HG-T series cannot be submerged in water or placed
under falling water for measurement operation. Pay attention to the environment where the
product is used.
Other matters
● Never attempt to disassemble, repair, or modify the product.
● When the product becomes unusable or unneeded, dispose the product appropriately as
industrial waste.
1.2 Handling Precautions
1-4 WUME-HGT-6

1.3 Laser Safety Standards
1.3.1 IEC / JIS / GB
To prevent laser products from affecting their users, IEC, JIS, and GB have the following
respective standards:
IEC: IEC 60825-1-2014
JIS: JIS C 6802-2014
GB: GB 7247.1-2012
These standards classify laser products into classes according to the danger level of laser, and
prescribe safety and preventive measures that should be implemented for each class.
This product belongs to "Class 1 laser product" according to JIS C 6802-2014 "Safety of Laser
Products".
Explanation of danger level
Classificatio
nOverview of danger evaluation
Class 1 This class of laser beams is safe when the operating state of the product is rightly predictable.
Class 1M This class of laser beams is safe when the operating state of the product is rightly predictable,
but direct intrabeam viewing by optical means can be dangerous.
Class 2 This class of laser beams is visible light and low output. Normally, eyes are protected by
aversion reaction such as blinking.
Class 2M
This class of laser beams is visible light and low output. Normally, eyes are protected by
aversion reaction such as blinking, but direct intrabeam viewing by optical means can be
dangerous.
Class 3R Direct intrabeam viewing is potentially dangerous, but the level of risk is lower than Class 3B
laser.
Class 3B Direct intrabeam viewing is always dangerous.
Class 4 This class of laser beams is high output. It has the ability to cause dangerous diffuse reflection.
Such laser beams cause skin disorders and have the risk of fire occurrence.
■Warning label
On the emitter side
1.3 Laser Safety Standards
WUME-HGT-6 1-5

1.3.2 FDA
■Exporting to the USA
If this product is incorporated into facilities or equipment to be exported to the USA, it is subject
to the laser regulations of the U.S. Food and Drug Administration (FDA). To prevent laser
products from affecting their users, PART1040 (Performance Standards for Light-Emitting
Products) was established as one of the FDA regulations. These standards classify laser
products into classes according to the danger level of laser and prescribe safety and preventive
measures that should be implemented for each class.
This product complies with the FDA regulations (21 CFR 1040. 10 and 1040.11) in accordance
with FDA Laser Notice No. 50. (Class 1 laser product)
■FDA regulations
Requirements Class(Note 1)
Ⅰ ⅡaⅡ ⅢaⅢbⅣ
Performance (for all laser products)
Protective housings [1040.10(f)(1)] R(Note 2) R(Note 2) R(Note 2) R(Note 2) R(Note 2) R(Note 2)
Safety interlock
[1040.10(f)(2)]
R(Note 3)
(Note 4)
R(Note 3)
(Note 4)
R(Note 3)
(Note 4)
R(Note 3)
(Note 4)
R(Note 3)
(Note 4)
R(Note 3)
(Note 4)
Location of controls [1040.10(f)(7)] N/A R R R R R
Viewing optics [1040.10(f)(8)] R R R R R R
Scanning safeguard [1040.10(f)(9)] R R R R R R
Performance (for laser systems)
Remote interlock connector
[1040.10(f)(3)]
N/A N/A N/A N/A R R
Key control [1040.10(f)(4)] N/A N/A N/A N/A R R
1.3 Laser Safety Standards
1-6 WUME-HGT-6

Requirements Class(Note 1)
Ⅰ ⅡaⅡ ⅢaⅢbⅣ
Emission indicator [1040.10(f)(5)] N/A N/A R R R(Note 10) R(Note 10)
Beam attenuator [1040.10(f)(6)] N/A N/A R R R R
Manual reset [1040.10(f)(10)] N/A N/A N/A N/A N/A R(Note 13)
Performance (for special-purpose products)
Medical use [1040.11(a)] S S S S(Note 8) S(Note 8) S(Note 8)
Surveying, leveling, and alignment
[1040.11(b)]
S S S S NP NP
Demonstration [1040.11(c)] S S S S S(Note 11) S(Note 11)
Labeling (for all laser products)
Certification and identification
[1010.2,3]
R R R R R R
Protective housings [1040.10(g)(6),
(7)]
DR(Note 5) R(Note 5) R(Note 5) R(Note 5) R(Note 5)
Openings [1040.10(g)(4)] N/A N/A N/A N/A N/A N/A
Class warning [1040.10(g)(1), (2),
(3)]
N/A R(Note 6) R(Note 7) R(Note 9) R(Note 12) R(Note 12)
Information (for all laser products)
User information [1040.10(h)(1)] R R R R R R
Product literature [1040.10(h)(2)(i)] N/A R R R R R
Service information [1040.10(h)(2)
(ii)]
R R R R R R
R : Required
N/A : Not applicable
S : Same requirements as for other products of the class
NP : Not permitted
D : Depends on the internal radiation level
(Note 1) Based on the maximum level of exposure to radiation during operation
(Note 2) Required wherever and whenever if exposure to laser radiation exceeding the limit of Class 1 is not
necessary to fulfill the functions of the product
(Note 3) Required for protective housings that are opened during operation or maintenance if radiation
exposure that occurs when the housing is opened is not always necessary
(Note 4) Requirements for interlock differ according to the class of internal radiation.
(Note 5) Wording differs according to the level and wavelength of laser radiation inside the protective housing.
(Note 6) A label that indicates a warning statement
(Note 7) CAUTION logo
(Note 8) A means is required to measure the level of laser radiation for the purpose of human body irradiation.
(Note 9) CAUTION is used when the radiation level is 2.5 mWcm-2 or lower, and DANGER is used when the
radiation level is higher than 2.5 mWcm-2.
(Note 10) Time lag is required between reading and emission.
1.3 Laser Safety Standards
WUME-HGT-6 1-7

(Note 11) Exception handling is required for laser products and light show for demonstration of Class IIIb or IV.
(Note 12) DANGER logo
(Note 13) Required since August 20, 1986
■Recognition / identification label
■Label position
Emitter
● Common to HG-T1010 and HG-T1110
1.3 Laser Safety Standards
1-8 WUME-HGT-6

1.4 Terminology
Term Description
Controller - Master unit A controller that can be used on a standalone basis
Controller - Slave unit A controller that is used by connecting to a master unit
Sensor head - Emitter A sensor head emitter that is used by connecting to a controller
Sensor head -
Receiver A sensor head receiver that is used by connecting to a controller
Sensor head
connection
cable
A cable that is used to connect a sensor head and controller
Side view attachment An attachment that is used to refract laser beams from the sensor head at 90 degrees
End plate A plate that is used to secure both ends of controllers to prevent the connectors from
coming off and causing a communication failure when controllers are connected
Communication unit An interface unit that enables measurement data and other data of connected
controllers to be monitored.(Note 1)
(Note 1) For details on communication units, refer to the user's manual for each communication unit.
1.4 Terminology
WUME-HGT-6 1-9

1.5 Contents of Package
The following accessories are included in the product package. Before using the product, make
sure that no items are missing.
Controller
HG-TC101 / Master unit of high-performance NPN
output type
HG-TC101-P / Master unit of high-performance PNP
output type
● Controller: 1 pc.
● Instruction Manual
(English / Japanese, Chinese / Korean): 1 pc. each
● General Information for Safety, Compliance, and
Instructions (23 languages): 1 pc.
HG-TC111 / Slave unit of high-performance NPN
output type
HG-TC111-P / Slave unit of high-performance PNP
output type
● Controller: 1 pc.
● Instruction manual
(English / Japanese, Chinese / Korean): 1 pc. each
● General Information for Safety, Compliance, and
Instructions (23 languages): 1 pc.
HG-TC113 / Slave unit of wire-saving type
● Controller: 1 pc.
● Instruction manual
(English / Japanese, Chinese / Korean): 1 pc. each
● General Information for Safety, Compliance, and
Instructions (23 languages): 1 pc.
Sensor head
HG-T1010 / Measurement width 10 mm, standard type
● Sensor head (emitter and receiver): 1 set
● Instruction manual
(English / Japanese, Chinese / Korean): 1 pc. each
HG-T1110 / Measurement width10 mm, slim type
● Sensor head (emitter and receiver): 1 set
● Instruction manual
(English / Japanese, Chinese / Korean): 1 pc. each
1.5 Contents of Package
1-10 WUME-HGT-6

Sensor head
● General Information for Safety, Compliance, and
Instructions (23 languages): 1 pc.
● General Information for Safety, Compliance, and
Instructions (23 languages): 1 pc.
Side view attachment Sensor head connection cable
HG-TSV10 / Side view attachment
● Attachment: 1 pc.(Note 1)
● M2 screw with washer (length: 4 mm): 2 pcs.
CN-HT-C2 / Cable length 2 m
CN-HT-C5 / Cable length 5 m
CN-HT-C10 / Cable length 10 m
CN-HT-C20 / Cable length 20 m
● Connection cable: 1 pc.
(Note 1) HG-TSV10 is sold by one unit. Two units are required for a pair of emitter and receiver.
End plate
MS-DIN-E / End plate
● Plate: Set of 2 pcs.
● Instruction manual
1.5 Contents of Package
WUME-HGT-6 1-11

1.6 Product Version and Functions
The following functions are added to the HG-TC□ series controllers and HG-T□ series sensor
heads manufactured in November 2020 onwards.
Added function Description Remarks
Assigned edge detection mode Operation mode "6.3.1 Operation Mode ( )"
Tab cancellation function Hold setting "7.2.1 Hold Settings ( )"
Hold state output External output "7.2.4 External Outputs
()"
Measured value reversal selection
function
Measured value reversal "7.2.13 Reverse of Measured Value
( )"
● The controllers and sensor heads manufactured in October 2020 or earlier do not support
the above functions. Please note this point.
■<How to check manufacturing year and month>
Check the manufacturing lot No. shown in the following figure.
■<How to interpret the manufacturing lot No.>
1.6 Product Version and Functions
1-12 WUME-HGT-6