2gig Technologies EDGE User manual

TM
2GIG EDGETM
Security & Smart
Home System
USER GUIDE

2GIG EDGE User Guide 2
TABLE OF CONTENTS
INTRODUCTION ................................................................................................5
TECHNICAL SUPPORT ..........................................................................................5
SYSTEM FEATURES AND CAPABILITIES ...........................................................................5
Features ...................................................................................................5
SAFETY PRECAUTIONS AND NOTATIONS ..........................................................................7
ADDITIONAL ACCESSORIES .....................................................................................7
Kits & Keypads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Antennas...................................................................................................7
Sensors & Peripherals ........................................................................................7
Smart Home Controls .........................................................................................7
SETUP AND INSTALLATION ......................................................................................8
24-Hour Alarm Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Alarm......................................................................................................8
Burglary Protection ...........................................................................................8
Security Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Fire and Gas Protection .......................................................................................8
Sensor Types ...............................................................................................8
Trouble Alerts ...............................................................................................8
Wired and Wireless Sensors....................................................................................8
Zones .....................................................................................................8
Limitations of Alarm Products ..................................................................................10
PANEL LED BEHAVIOR ..........................................................................................11
THE TOUCHSCREEN ............................................................................................12
The Home Screen .............................................................................................12
System Status Messages.......................................................................................13
System Icons.................................................................................................13
Notications .................................................................................................14
Acknowledging an Alarm Message...............................................................................14
Reading Incoming Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Marking a Message as Read ...................................................................................15
Marking a Message as Unread..................................................................................15
Deleting a Message ..........................................................................................15
Emergency Button/Indicator ....................................................................................16
Viewing the Weather Forecast...................................................................................16
Panel Information .............................................................................................16
System Settings Button ........................................................................................16
RESPONDING TO TROUBLE ALERTS ..............................................................................17
Monitoring the System for Trouble Conditions ......................................................................17
When a Trouble Condition Occurs ...............................................................................17
BURGLARY PROTECTION........................................................................................18
To help you get the most out of the burglary protection part of the system, it is useful to understand the concepts. ................18
Perimeter and Interior Sensors..................................................................................18
Protection Zones.............................................................................................18
Stay and Away Mode .........................................................................................18
Open and Closed Sensors .....................................................................................18
Bypassed Sensors ...........................................................................................19
REMOTE CONTROL DEVICES.....................................................................................19
Operate the System with a Keyfob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Arming the System Using a Keyfob ..............................................................................19
Disarming the System Using a Keyfob ............................................................................19
Activating an Auxiliary Function .................................................................................19
Activating an Alarm Using a Keyfob ..............................................................................19
SAMPLE BURGLARY ALARM PLAN................................................................................20
ARMING THE SYSTEM...........................................................................................21
Arm the System (Stay Mode) ...................................................................................21
Arm the System (Away Mode) ..................................................................................22
Force Bypassing..............................................................................................23
Opening a Sensor When the System is Disarmed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Force Bypassing a Sensor .....................................................................................23

Copyright © 2021 Nortek Security & Control LLC
3
Use the Quick Exit Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
In the Event of an Exit Error ....................................................................................25
DISARMING THE SYSTEM........................................................................................26
Disarm the System (Stay Mode).................................................................................26
Disarm the System (Away Mode) ................................................................................26
Disarm the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Facial Recognition Prole Update ...............................................................................27
Transmit a User Duress Report ..................................................................................29
Transmitting a User Duress Report when the System is Armed ........................................................29
Transmit a Duress Signal when System is Disarmed .................................................................30
In the Event of a Burglary Alarm .................................................................................30
Silencing the Alarm Sounder (for False Alarms) .....................................................................30
Clearing an Alarm ............................................................................................31
Clear the Alarm History ........................................................................................32
Emergency Features ..........................................................................................33
24-Hour Alarm Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Panic Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Fire Button .................................................................................................33
Activate an Emergency Alarm...................................................................................34
Activate a Manual Panic, Fire or Emergency Alarm ..................................................................34
PANEL INFORMATION ...........................................................................................34
History ......................................................................................................34
Filtering History ..............................................................................................35
System Info ..................................................................................................35
Reboot ....................................................................................................35
Dealer Info ...................................................................................................35
FIRE AND CARBON MONOXIDE PROTECTION.......................................................................36
Important Concepts ...........................................................................................36
National Fire Alarm and Signaling Code ..........................................................................36
Emergency Action Plan ........................................................................................36
In the Event of a Fire Alarm ....................................................................................36
Silence a False Fire Alarm .....................................................................................37
In the Event of a Carbon Monoxide Alarm .........................................................................37
ALARM.COM SETUP ............................................................................................38
Video .......................................................................................................39
Automation ..................................................................................................39
Notications .................................................................................................39
Activity.....................................................................................................39
Users .......................................................................................................39
Adding a New User...........................................................................................39
Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Login Settings ...............................................................................................40
Account Management.........................................................................................40
Devices ....................................................................................................40
Geo-Services ...............................................................................................40
THE ALARM.COM MOBILE APP ...................................................................................41
Arming ......................................................................................................41
Disarming ...................................................................................................41
SYSTEM SETTINGS .............................................................................................42
Screen ......................................................................................................42
Screen Brightness............................................................................................42
Screen Timeout..............................................................................................42
Screen Saver ...............................................................................................42
Clean Screen ...............................................................................................43
Sounds......................................................................................................43
Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Connect to a Wireless Network..................................................................................44
Forget Network ..............................................................................................44
Join Other Network ...........................................................................................45
WPS ......................................................................................................46
Access Point ...............................................................................................46
Users .......................................................................................................47
Types of User Codes .........................................................................................47

2GIG EDGE User Guide 4
Adding a User ...............................................................................................47
Capture a Prole.............................................................................................48
Prole - Facial Recognition.....................................................................................49
Capturing Your Avatar .........................................................................................50
Editing a User . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
Access Code................................................................................................52
Activating the Duress Code.....................................................................................52
Enable Facial Recognition......................................................................................53
Smart Home Settings ..........................................................................................54
Bypass Sensors ..............................................................................................54
Manually Bypassing a Sensor...................................................................................54
Removing Sensors from Bypassed Sensors List ....................................................................54
Chimes......................................................................................................55
On-Board Camera.............................................................................................55
Date & Time..................................................................................................56
System Tests.................................................................................................56
Sensors Test ................................................................................................56
Panel Tests .................................................................................................57
Cell Radio Status ............................................................................................57
Network Tests ...............................................................................................58
Firmware Update ............................................................................................58
LIMITED WARRANTY ............................................................................................59
Waste Electrical and Electronic Equipment (WEEE) Statement .......................................................59
WARNINGS ....................................................................................................59
Limitations of Alarm Products ..................................................................................59
Risk of Noise Induced Hearing Loss .............................................................................59

Copyright © 2021 Nortek Security & Control LLC
5
INTRODUCTION
This guide is designed for end users of the 2GIG EDGE Security & Smart Home System. It provides general system
information, safety precautions, and step-by-step instructions for operating the system. It is intended for use only by 2GIG
EDGE owners whose system has been professional installed in a residential or commercial setting by an authorized 2GIG
alarm dealer.
For a list of 2GIG alarm dealers and distributors in your area, visit: http://www.nortekcontrol.com or http://www.2gig.com.
TECHNICAL SUPPORT
Should you require support services for this system, contact 2GIG Technical Support at Nortek Security & Control.
For support in the USA and Canada, contact 2GIG Technical Support at Nortek Security & Control:
»Phone: [phone]
»Online: www.nortekcontrol.com/support/
For support outside of the USA or Canada, contact a regional 2GIG distributor. For a list of distributors in your region, visit
the websites above.
SYSTEM FEATURES AND CAPABILITIES
The 2GIG EDGE Panel from Nortek Security & Control introduces a major visual upgrade— offering a larger, touchscreen
only experience, Facial Recognition, Bluetooth disarm and an intuitive user interface featuring convenient, gesture-based
navigation.
Features
The system includes:
»Facial Recognition: Built-in camera recognizes faces and can disarm the system as well as activate
personalized home control features.
»Bluetooth disarm: With Bluetooth capability, easily disarm the system without touching the panel.
»Photo snapshot: On-board camera takes arm/disarm photos adding additional security and peace of mind
knowing user codes are used by authorized user.
»Slideshow & Video Playback: Videos and pictures can play on screen, making it easy to show how-to training
videos or turn the panel into a photo display.
»Video Live View: Cameras and doorbell cameras work with the panel, with up to 8 different camera feeds
viewable directly from the panel. View 4 camera feeds at a time.
»Doorbell on the Panel: See who’s at the door and talk to them right from the panel.
»Touchscreen Display: A large, full-color, 7-in (17.8 cm) diagonal touchscreen with an intuitive user interface.
»Built-in Glass Break: Save on hardware costs by using the panel as a glass break sensor.
»Data Privacy & 2GIG EDGE processing of personal data: Rather than sending images and private biometric
data to the Cloud for processing, 2GIG EDGE panel uses on-the-edge analytics to process and authenticate
faces privately.

2GIG EDGE User Guide 6
»Smart Home Controls & Scenes: Customize your living space with advance automation rules, scenes and
notications to best t your unique needs.
»Geofencing: Location services allow for scenes activated based on location.
»LTE Communication: Long Term Evolution with 4G connectivity to carrier networks (eg; Verizon, AT&T).
»Mobile System Control: Easily control your system remotely utilizing your Remote Service Provider app.
»Dual Path (WiFi/Cell): System communicates to the network using both the cellular LTE and Wi-Fi. If one
service goes down for any reason, the other is always available and communicating. Enjoy free and faster
updates with Wi-Fi connection.
»Piezo Sounder and Internal Speaker: An extremely loud Piezo Sounder sounds external alarms. An internal
speaker to delivers voice annunciations, chimes, other system notications.
CAUTION! Long or repeated exposure to sounds at or above 85 dB can lead to Noise-Induced Hearing Loss (NIHL).
»LED Indicator: Multi-color LED always keeps you informed of the system state.
»Home Button: A soft button from any screen. Tap display to wake up the touchscreen to return to the
touchscreen’s Home screen (see The Home Screen, page 12).
»Microphone and Speaker: Built-in dual microphone with echo and noise cancellation provides clear 2-Way
Voice communication during alarm events between users at the 2GIG EDGE Panel and operators at the Central
Station.
»24-Hour Backup Battery: A 24-hour rechargeable backup battery to support the 2GIG EDGE Panel during
temporary AC power failures and outages.
»USB Port: A convenient USB port at the top of the 2GIG EDGE Panel that can be used with a USB thumb drive
(not supplied) to update the system’s rmware. See Firmware Update, pg. 58.
»WiFi: The built-in WiFi module allows the system to be connected to a WiFi network for dual path
communication, OTA updates, and connection with secondary keypads.
»Access Point: The built-in Access Point allows for a direct connection with secondary keypads and approved
cameras and doorbells via WiFi.
»Smart Areas: (Optional) The system supports a Maximum of 4 Smart Areas. Zones may be assigned across
Smart Areas to allow for independent control.
»Security Codes (4 digit or 6 digit): The system supports a maximum of 100 unique, programmable, security
codes for accessing system functions. Provided are one (1) Master User Code, one (1) Duress Code, and one
(1) Installer Code (reserved for use by 2GIG alarm dealers and installers), and the ability to create 98 additional
user codes for accessing the system.
»Z-Wave™Z-Wave Plus™ and S2 Compatibility: Installers (and end users, if congured on the system) can
add up to 232 smart home devices to communicate with the 2GIG EDGE Panel using the Z- Wave and Z-Wave
Plus V2 wireless communication protocol. The 2GIG EDGE Panel can be included and operated in any Z-Wave
network with other Z-Wave certied devices from other manufacturers and/or other applications. All non-battery
operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the
network. This device is a security enabled Z-Wave Plus V2 product that is able to use encrypted Z-Wave Plus
V2 messages to communicate to other security enabled Z-Wave Plus V2 products.
»2-Way Voice: (Optional) Operators at the Central Station can communicate directly with end users through the
2GIG EDGE Panel . Operators can also silently listen-in after receiving a user duress report.
»Date, Time, and Weather Forecasts1: Users can view the current date, time, and weather forecast in an easy-
to-read format.
»System Vocabulary/Voice Descriptors: A list of vocabulary words integrates with the on-screen user interface
and audio announcements. This lets installers customize the sensor names that display on the 2GIG EDGE
Panel, as well as for the audible system announcements. For example, when someone opens the front door,
the system can be set up to announce “front door”.
1Date, Time and Weather Forecasts are supported by most Remote Service Providers in most regions. Consult the provider to determine if this feature is enabled.

Copyright © 2021 Nortek Security & Control LLC
7
SAFETY PRECAUTIONS AND NOTATIONS
It is imperative that you observe all of the safety precautions documented in this guide. For your safety and the safety of
others, the following table details how this guide calls special attention to information intended to safeguard life, health,
and property.
DANGER!!! This notation is used to indicate hazardous
situations which, if not avoided, will result in serious injury
or death.
WARNING!! This notation is used to indicate potentially
hazardous situations which, if not avoided, could result in
serious injury or death.
CAUTION! This notation is used to indicate a potentially
hazardous situation which, if not avoided, could result in
minor or moderate injury.
IMPORTANT: This notation is used to indicate a situation
which, if not avoided, could result in property damage,
equipment damage, or data loss.
NOTE: This notation is used to call attention to notable
information that should be followed when installing,
servicing, or using this product.
TIP: This notation is used to call attention to helpful hints
related to using the product.
ADDITIONAL ACCESSORIES
The installer typically sets up the system to communicate with a variety of wired and/or wireless sensors. Some sensors
are visible on the wall or ceiling. For example, Wireless Smoke/Heat/Freeze Alarms and Wireless Carbon Monoxide
Detectors. Others may be hidden in door jambs. For example, Recessed Door/Window Contacts. Sensors might also be
installed in additional locations. For example, a Glass Break Detector and a Passive Infrared Motion Detector.
NOTE: A variety of 2GIG and GoControl branded devices are compatible with the 2GIG EDGE Security & Smart
Home System. Sensors manufactured by other companies may also be compatible with the system.
IMPORTANT: To ensure that the system’s sensors are operating properly, it is important for 2GIG alarm dealers
and system owners to ensure sensor batteries and wireless signals are tested at least once a year.
Depending on the specic installation, systems may also be installed with one or more of the following 2GIG accessories:
Kits & Keypads
»2GIG Control Panel Desktop Kit
»2GIG EDGE Remote Keypad
»2GIG PAD1
Antennas
»2GIG External Attic Mount Antenna
Sensors & Peripherals
»2GIG Thin Door/Window Surface Contact
»2GIG Recessed Door/Window Contact
»2GIG Passive Infrared (PIR) Motion Detector
»2GIG Glass Break Detector
»2GIG Smoke/Heat/Freeze Alarm
»2GIG Smoke/Heat Detector
»2GIG Panic Button Remote
»2GIG Carbon Monoxide Sensor
»2GIG Takeover Module
»2GIG Doorbell
»Universal Garage Door Receiver
»2GIG Tilt Sensor
»2GIG Bypass Sensor
»2GIG Flood Sensor
»2GIG Repeater
NOTE: eSeries sensors are only compatible with
eSeries panels including 2GIG EDGE.
Smart Home Controls
Consult a 2GIG alarm dealer for information about installing
compatible Z-Wave smart home controls including:
»Lights
»Locks
»Thermostats
»Garage Doors
»Doorbells

2GIG EDGE User Guide 8
SETUP AND INSTALLATION
The 2GIG EDGE Security & Smart Home System must be installed by a qualied technician who is either employed by, or
under contract with, a 2GIG alarm dealer. The alarm must always be installed in accordance with your country’s national
electrical installation regulations and/or all applicable codes in the local jurisdiction.
Understanding these concepts will help when operating the system:
24-Hour Alarm Buttons
An installer can congure the 2GIG EDGE Panel to show or hide three 24-hour alarm buttons on the touchscreen: Panic,
Fire, and Emergency. When the buttons are enabled and visible, users can manually trigger an alarm from the 2GIG
EDGE Panel. Alarms can also be activated from a wireless keypad (if installed), from wireless sensors, or from portable
devices (for example, a Panic Button Remote). See Emergency Features, pg. 33.
Alarm
When the system detects an alarm condition, it immediately sounds an audible alarm that continues for a preset amount
of time. If external alarm sounders or Z-Wave sirens have been installed, those devices also sound an audible alarm.
During an alarm (and also after a user cancels or clears the alarm), the Alarm History reveals a chronological list of the
alarms that have occurred by zone. The next time the system is armed, the system automatically clears the history. The
history can also be cleared manually.
See Clear the Alarm History, pg. 32.
Burglary Protection
Burglary protection is provided by a combination of perimeter and interior sensors installed on doors, windows, and other
areas of a dwelling. See Burglary Protection, pg. 18.
Security Codes
The system supports a maximum of 100 unique security codes (4 digit or 6 digit). There are four types of security codes
supported by the system: (1) Master User, (2) User, (3) Duress, and (4) the Installer Code, which is reserved for use by
2GIG alarm dealers and installer. See Users, pg. 47.
Fire and Gas Protection
Fire and gas protection are provided by a combination of Wireless Carbon Monoxide Detectors and Wireless Smoke/Heat/
Freeze Alarms that protect a dwelling 24 hours-a-day. When an alarm condition is detected, the system sounds an alarm
and transmits a report to the Central Station so operators can dispatch the appropriate emergency services. See Fire &
Carbon Monoxide Protection, pg. 36.
Sensor Types
When programming the sensor into the system, the installer sets the sensor type for each device. This determines how
and when the system will react when a sensor detects an alarm condition. Fire protection sensors protect the dwelling
24-hours a day, whereas burglary protection sensors only protect the premises when the system is armed.
Trouble Alerts
The system monitors itself for abnormal operating conditions and alerts when trouble is detected. Examples of alert
conditions include AC power loss at the 2GIG EDGE Panel, low battery conditions at a sensor and more. See Responding
to Trouble Alerts, pg. 17. The installer can congure the system to transmit a variety of trouble alerts to the Central
Station.
Wired and Wireless Sensors
Your system can be installed with wired sensors, wireless sensors or a combination of both. Some sensors are visible on
the wall or ceiling (for example, Wireless Smoke/Heat/Freeze Alarms and Wireless Carbon Monoxide Detectors), while
others may be hidden in doorjambs (for example, Recessed Door Contacts). Sensors can also be mounted in different
locations (for example, Glass Break Detectors and Passive Infrared Motion Detectors).
Zones
The system’s wired and/or wireless sensors that have been programmed by the installer are also sometimes referred
to as zones. Examples of zones that are typically set up for a home installation include Front Door, Sliding Glass Door,
Living Room Bay Window, and so on.

Copyright © 2021 Nortek Security & Control LLC
9
Use and Care of the System
To care for the system, observe the following:
»Humidity and Liquids Do not expose the system to water, rain, extreme humidity, perspiration, or other liquids.
The optimum humidity range for the system is 9-90% non-condensing.
»Extreme Heat or Cold Do not expose the system to extreme heat or cold. The optimum operating temperature
range is: 32 F to 104 F (0 C to 40 C). Do not expose system to direct sunlight.
»Shock and Vibration For optimum protection against shock and vibration, make sure that your installer has
securely mounted the touchscreen ush against the wall or properly installed it in a compatible desktop kit.
IMPORTANT: To prevent touchscreen damage during cleaning, see Screensaver: Clean Mode, pg. 42.
ANSI/SIA CP-01-2010 2GIG System Feature User Guide
4.2.2.1 Exit Time Exit Delay "Important Concepts" "Arm the System"
4.2.2.2 Progress Annunciation Exit Delay Announcement "Important Concepts" "Arm the System"
4.2.2.3 Exit Time Restart Exit Delay Restart "Important Concepts" "Arm the System"
4.2.2.4 Exit Error Exit Error "In the event of an Exit Error"
4.2.2.5 Unvacated Premises Auto Stay "Arm the System (Away Mode)"
4.2.3.1 Entry Delay Entry Delay "Important Concepts" "Disarming the System"
4.2.3.3 Disarm Disarming Features "Disarms the Alarm System"
4.2.4.1 Control Buttons Keyfob/Remote Arming Mode on System Not Ready "Remote Control Devices"
4.2.4.2 Manual Alarms Emergency Alarm Features "Activate a Manual Panic, Fire, or Emergency Alarm"
4.2.4.3 System Acknowledgement Alert Keyfob Disarming Afte Alarm, Keyfob Arm/Disarm,
Conrmation "Arming the System Using a Keyfob"
4.2.4.4 Remote Alarming Keyfob Arming "Arming the System Using a Keyfob"
4.2.4.5 Remote Disarming Keyfob Disarming "Disarming the System Using a Keyfob"
4.2.5.1 Abort Window Abort Window Dialer Delay "In the Event of a Burglary Alarm"
4.2.5.1.1 Disarm Alarm Annunciation Silence "In the Event of a Burglary Alarm"
4.2.5.1.2 Abort Abort Window Alarm Cancel "In the Event of a Burglary Alarm"
4.2.5.2 Alarm Transmission Alarm Signal Sent "In the Event of a Burglary Alarm"
4.2.5.3 Disarm Panel Alarm Annunciation "Disarming the System"
4.2.5.4 Cancel Window Alarm Cancel Time, Alarm Cancel Display "In the Event of a Burglary Alarm" "Silence a False Alarm"
4.2.6.1 Use of Duress Feature User Duress Report "Transmit a User Duress Report"
4.2.6.2 Duress Code Duress Code "Types of User Codes" "Users"
4.2.7 Initiation of Manual Alarms Panic, Fire, or Emergency Alarm "Activate a Manual Panic, Fire, or Emergency Alarm"
4.3.1 Cross Zoning Cross Zone Verication "Cross Sensor Zones"
4.3.2 Swinger Shutdown Swinger Trouble "Sensor Trip Error"
4.3.3 Fire Alarm Fire & Carbon Monoxide Protection "Fire & Carbon Monoxide Protection"
4.6.3 System Test Panel Test, Sensor Test "Testing the System"
4.6.6 Test in Progress Test is in Progress "Testing in Progress"

2GIG EDGE User Guide 10
Limitations of Alarm Products
This security system cannot offer guaranteed protection against burglary, re, or other emergencies. Any alarm, whether
commercial or residential, is subject to compromise or failure to warn for a variety of reasons. For example:
»Intruders may gain access through unprotected openings or have the technical sophistication to bypass an
alarm sensor or disconnect an alarm warning device.
»Intrusion detectors (sensors) do not work without power. Battery operated devices do not work without batteries,
with dead batteries, or if the batteries are not put in properly. Devices powered solely by AC do not work if their
AC power supply is cut off for any reason, however briey.
»Signals sent by wireless sensors may be blocked or reected by metal before they reach the alarm Control
Panel, even if the signal path has been recently checked during a weekly test.
»Blockage can occur if a metal object has been moved into the sensor’s signal path.
»A user may not be able to reach a panic or emergency button quickly enough.
»Cellular or broadband network is needed to transmit alarm signals from a premises to a Central Station may be
out of service or temporarily out of service. Telephone lines are also subject to compromise by sophisticated
intruders.
»Even if the system responds to the emergency as intended, however, occupants may have insufcient time to
protect themselves from the emergency situation. In the case of a monitored alarm system, authorities may not
respond appropriately.
»Alarm warning devices such as sirens, bells, or horns may not alert people or wake up sleepers if they are
located on the other side of closed or partly open doors. If warning devices sound on a different level of the
residence from the bedrooms, then they are less likely to waken or alert people inside the bedrooms. Even
persons who are awake may not hear the warning if the alarm is mufed from a stereo, radio, air conditioner,
or other appliance, or by passing trafc. Finally, alarm warning devices, however loud, may not warn hearing-
impaired people or awaken deep sleepers.
»While smoke detectors have played a key role in reducing residential re deaths, they may not activate
or provide early warning for a variety of reasons in as many as 35% of all res. This is according to data
published by the Federal Emergency Management Agency. Some of the reasons smoke detectors used in
conjunction with this system may not work are where smoke cannot reach the detectors, such as in chimneys,
in walls, or roofs, or on the other side of closed doors. Smoke detectors may have been improperly installed
and positioned. Smoke detectors also may not sense a re on another level of a residence or building. A
second-oor detector, for example, may not sense a rst oor or basement re. Moreover, smoke detectors
have sensing limitations. No smoke detector can sense every kind of re every time. In general, detectors may
not always warn about res caused by carelessness and safety hazards like smoking in bed, violent explosions,
escaping gas, improper storage of ammable materials, overloaded electrical circuits, children playing with
matches or arson. Depending upon the nature of the re and/or the locations of the smoke detectors, the
detector, even if it operates as anticipated, may not provide sufcient warning to allow occupants to escape in
time to prevent injury or death.
»This equipment, like other electrical devices, is subject to component failure. Even though this equipment is
designed to last as long as ten years, the electronic components could fail at any time.
The most common cause of an alarm system not functioning when an intrusion or re occurs is inadequate maintenance.
Although installing an alarm system may make homeowners eligible for lower insurance rates, an alarm system is not
a substitute for insurance. Homeowners, property owners, and renters should continue to act prudently in protecting
themselves and continue to insure their lives and property.

Copyright © 2021 Nortek Security & Control LLC
11
PANEL LED BEHAVIOR
The 2GIG EDGE panel has a single LED light on the top right corner. Depending on the panel's alarm status, the multi-
colored LED that will ash blue, white or red (see Alarm Status table below).
Alarm Status AC Power LED Status Battery Power LED Status
System Ready to Arm (all sensors closed) Solid Blue Flashing Blue
System Not Ready to Arm (one or more sensors open) Solid White Blinking White
Exit Delay Countdown / Armed Solid Red Flashing Red
Entry Delay Countdown / In Alarm / Armed After Alarm Blinking Red Blinking Red
Microphones
Camera
Alarm
Status
Red
White
Blue
Speakers

2GIG EDGE User Guide 12
THE TOUCHSCREEN
During periods of inactivity, the touchscreen automatically times out or starts the photo slideshow.
Tap any area on the touchscreen to wake the touchscreen.
By default, the touchscreen enters sleep mode after one (1) minutes of inactivity.
To select a setting between 30 seconds and 10 minutes:
1. Tap System Settings ( ).
2. Display your face to the camera, or enter the Master User Code.
3. Tap Screen ( ).
4. Tap Screen Timeout to access options and change the setting.
5. Tap to return to the previous menu.
The Home Screen
When you rst wake the system, it reveals the Home screen.










Feature Does this ...
❶System Status Reveals the system state: Ready to Arm, Not Ready to Arm, etc.
❷Date/Time Shows the system date/time.
❸Arming Features Tap Arm Stay or Arm Away to arm the system.
❹Emergency Icon Tap for access to Panic, Fire and Emergency buttons.
❺System Logo
Tap System logo to access History, System Info, Dealer Info and Regulatory & Compliance.
Press and Hold for 3 seconds for access to enter the Duress Code and transmit a user duress report
to the Central Station.
❻Current Weather This feature requires a service agreement. Contact your dealer for details.
❼System Icons Indicates system information.
❽Smart Home Tap for Smart Home options.
❾Smart Areas Icon Tap to access Smart Areas status and arm/disarm options.
❿Settings Icon Tap for access to the Settings menu.

Copyright © 2021 Nortek Security & Control LLC
13
System Status Messages
At the top-left of the screen, different messages appear to reveal the current system state.
System Status Messages
This table describes the different system status messages on the system.
This system status message ... Indicates that ...
System Ready To Arm Indicates all sensors are closed and the system is ready to be armed.
System Not Ready to Arm One or more sensors are open.
System Ready To Arm (BYPASS) The system is ready to arm and one or more sensors are on the Bypassed Sensors list.
See Force Bypassing, pg. 23.
System Arming (STAY) The system is in the process of arming itself in Stay Mode.
System Arming (AWAY) The system is in the process of arming itself in Away Mode.
System Armed (Stay)
System Armed (Away) The system is armed and protecting the premises in STAY or AWAY mode.
Restarting Security Process The security system is restarting. Typically, this only appears after an installer modies a
System Conguration setting.
System Icons
The status bar that appears on the top of the Home screen and on most system menus reveals a variety of icons
providing system information and access to different functions.
System Status Bar
System Icons
Status Icons Action Icons
Battery Power Status Notications
Battery Charging Turn Display Sleep Mode On
On-Board Camera is active Audible Beeps On
Power Audible Beeps Off
Power Disconnected Update is available

14
2GIG EDGE User Guide
Notications
There are three (3) types of messages that arrive as
Notications: Alerts, Alarms, and Messages.
The Notications system produces an icon at the top
of the screen that blinks and shows the number of new,
unread messages. New messages are accompanied by
beeps, once every minute until the message is read.
To read an alert message:
1. Tap the Notication icon ( ).
2. In the drop-down menu, tap Alerts. The system
reveals the alert messages.
Notications Icon
Unread Messages > Alert Messages
Acknowledging an Alarm Message
If the system goes into an alarm state, a message is
sent to the Inbox. To view an alarm message:
1. Tap the Notication icon ( ).
2. In the drop-down menu, tap Alarms. The system
reveals the alarm messages.
3. Press the back button ( ) to return to the
previous screen.
Unread Messages > Alarm Message
Reading Incoming Messages
Your security provider has the ability to transmit
messages about the installed 2GIG EDGE system.
When transmitting messages to the system, your
security provider can:
»Mark a Message as Public (read by any user)
or Private (opened only by users who know
the Master User Code).
»Classify a Message as High Priority
(ORANGE) or Low Priority (BLACK).
»Specify When or If Messages Expire: There
is no limit to the number of messages in the
Inbox, but expired messages are automatically
removed from the Inbox.
To read messages sent by your security provider:
1. Tap the Notications icon.
2. In the drop-down menu, tap Messages. Before
opening the message, it helps to understand the
following:
»Messages in BLACK indicate Low priority.
»Messages in ORANGE indicate High priority.
»Messages in RED indicate an Emergency.
»Messages in GREY indicate that the message
has been opened.
»A Lock icon indicates a Private message ( ).
Messages > Reading Messages
Messages—Priority and Security

15 Copyright © 2021 Nortek Security & Control LLC
4. Tap the desired message to open it.
5. If the message was marked as private, enter your
system’s Master User Code.
6. When the message appears, read the text.
Enter Your Code to Read the Message
Marking a Message as Read
After reading a message, the system automatically
marks the message as read. You can also manually
mark the message as read.
To mark a message as read:
1. Open the desired message.
2. After reading the text, tap MARK AS READ. The
system marks the message as read.
Messages > Mark as Read Button
Marking a Message as Unread
If you want to keep a message in the unread status after
reading it, you can mark the message as unread. To
mark a message as unread:
1. Open the desired message.
2. After reading the text, tap MARK AS UNREAD.
The system marks the message as unread.
Messages > Mark as Unread Button
Deleting a Message
To delete a message:
1. Open the desired message.
2. After reading the text, tap DELETE MESSAGE.
Messages > Delete Message Button

16
2GIG EDGE User Guide
Emergency Button/Indicator
Announce an emergency event by manually activating
the alarm at the Control Panel.
This button is available on most displays (other than
some system setup menus) for access to Panic, Fire or
Emergency alarms.
See Emergency Features, pg. 33, for complete
instructions.
2GIG EDGE Panel—Alarm Button
Viewing the Weather Forecast
Weather forecasts can be added as part of a service
agreement. You can view ve-day weather forecasts by
tapping on the single day weather information on the
Home screen of the touchscreen display.
Five-Day Weather Forecast
Panel Information
Tap the 2GIG Logo on the Home screen to reveal the
Panel Information menu. This menu provides access to
system History, System Information, Dealer Info (contact
information for your 2GIG alarm dealer) and Regulatory
& Compliance information.
Panel Information
System Settings Button
Tap the System Settings button ( ) on the Home
screen to reveal the System Settings menu and access
general settings for the 2GIG EDGE Security & Smart
Home System. To learn about the options in this menu,
see System Settings, pg. 42.
NOTE: To use this feature, you must know the
Master User Code.
Screen image oversized to display all icons ➔
System Settings Menu

Copyright © 2021 Nortek Security & Control LLC
17
RESPONDING TO TROUBLE ALERTS
To ensure that all system components are operating under optimal conditions, the system continually polls all of the
wired and wireless sensors paired with the system. It also continuously checks the 2GIG EDGE Panel to ensure that it is
operating properly. If a trouble condition is detected, the system alerts you of the issue.
Monitoring the System for Trouble Conditions
The system monitors the 2GIG EDGE Panel and its sensors, so it can notify you when the following trouble conditions
occur:
»AC power loss to the panel
»Cell radio connection interruption
»Sensor low battery
»Panel backup battery is low, bad or not installed
»Sensor tamper
»Panel tamper
»Sensor supervision
»Broadband network connection loss
»RF Jam
When a Trouble Condition Occurs
When a trouble condition occurs, the system alerts you so that you can promptly address the issue and return your
system to proper working order. In some cases, you may need to contact your 2GIG alarm dealer for assistance in
resolving the trouble condition.
»An alert notication is sent to the system’s Inbox and the Messages icon ashes.
»The system tones at 10 sec intervals every minute, until the alert is acknowledged.
»Some Trouble Conditions are acknowledged by one beep, and then they transition to visual Trouble alert.
NOTES:
1 Attention required to the alert notications will vary depending upon the severity of the trouble. Some troubles
may create an audible alert and automatically transfer future alerts to a visual indicator on the panel. The visual
alert will remain until the trouble has been resolved.
2 In some cases, an audible trouble alert will occur until acknowledged and repeat every 4 hrs until the condition
causing the trouble has been resolved. Depending on the trouble type, you may have the option to transfer
future alerts for the acknowledged trouble to be visual until the trouble has been resolved.
3 Acknowledging the trouble alerts may possibly be performed remotely through the Alarm.com app. Consult
your 2GIG dealer or ADC account for more details.
4 Troubles that affect the whole system or Life Safety sensors are “Global”. They will display and need to be
acknowledged in each Smart Area.
5 Consult your installer to determine if the Trouble Doesn’t Sound at Night feature is enabled on the system. When
enabled, the system silences only the audible trouble alerts only during the hours of 10 p.m. to 9 a.m. It will not
stop the visual trouble alert notication from displaying on the touchscreen so they can be acknowledged, nor will
it stop the trouble alert report from being sent to the Central Station.
6 For compliance with UL 985: Household Fire Warning System Units, the six (6) trouble alert tones for Wireless
Smoke/Heat/Freeze Alarms and Wireless Carbon Monoxide Detectors are required to sound at an interval of
once every four (4) hours, until the condition causing the alert is resolved.
»A trouble report is sent to the Central Station.
7 Consult your installer to determine if the Trouble Reports to CS feature is enabled. When enabled, the system
transmits trouble reports about sensors to the Central Station.

2GIG EDGE User Guide 18
BURGLARY PROTECTION
During setup, the installer typically congures a variety of wireless and wired sensors to protect your dwelling from
unwanted intrusion. Different types of sensors may be installed in your dwelling for burglary protection including door/
window contacts, glassbreak detectors, image sensors and motion detectors. These sensors are intended to protect both
the perimeter and interior of the premises.
NOTE: This burglary alarm system is in compliance with the standards dened in UL 681: Installation and
Classication of Burglar and Holdup Alarm Systems and UL 827: Central- Station Alarm Services.
To help you get the most out of the burglary protection part of the system, it is useful to understand the concepts.
Perimeter and Interior Sensors
The system provides burglary protection using a combination of sensors that have been installed in and around your
dwelling:
»Perimeter Sensors: Sensors intended to place the system into an alarm state when an intruder enters a
dwelling. Perimeter sensors (for example, Door/Window Contacts and Wireless Glass Break Detectors) are
typically installed at possible entry points, such as front doors, sliding glass doors, back doors, side doors,
garage doors, and windows.
»Interior Sensors: Sensors intended to place the system into an alarm state by detecting forced entry of the
premises by an intruder. Interior sensors are typically installed at possible movement points. For example, a
motion detector might be installed to detect movement across a basement, down a hallway, or up a stairwell.
Once installed, the system continuously monitors all of its sensors. For an alarm to sound, burglary protection sensors
must be armed (see Arming the System, pg. 21).
The system is also programmed by the installer to notify you about different events. For example, when you open a
perimeter door, it transmits a status message to the 2GIG EDGE Panel. The panel then shows that the door is open and
the system announces the door’s voice descriptor.
Protection Zones
When programmed into the system by the installer, each sensor is intended to protect a particular zone. Typical examples
of zones that may be protected by a sensor include, Front Door, Back Door, Basement Window, Laundry Room, and so
on. During programming, the installer may also create a voice descriptor for each zone. The 2GIG EDGE Panel uses the
voice descriptor in two ways:
»As a verbal announcement to notify occupants when a perimeter sensor is open, closed, or when an alarm is
set off.
»As the display name of the sensor’s zone on the touchscreen.
Stay and Away Mode
Unlike re protection sensors (which are always ON and protecting the dwelling), burglary protection sensors must be
turned ON (see Arming the System, pg. 21) and OFF (see Disarming the System, pg. 26). This system can be armed in
one of two modes:
»Stay Mode: Arms the system except interior sensors. Arm the system in this mode when individuals will be
occupying the premises. This arms only the sensor-protected perimeter doors and windows, leaving interior
motion sensors or other interior doors unarmed. In a home setting, Stay Mode is frequently used during the
evening hours when occupants do not intend to enter or exit the dwelling. This lets you move about without
triggering the burglary alarm. Because all the interior burglary protection is OFF, an alarm would only be
triggered if a sensor-protected perimeter door or window is opened.
»Away Mode: Arms the system including interior sensors. Use this mode to arm the system when everyone
will be leaving the premises. This mode arms all sensor-protected perimeter doors and windows, interior
motion sensors, interior glass break sensors, and any other sensor-protected interior doors. Away Mode is
frequently used during day time hours in residential installations and during non-business hours in commercial
installations. Because all burglary protection features are ON, an alarm would be triggered when movement
is detected, if any protected doors or windows are opened, or if glass breakage is detected (if glass break
detectors have been installed).
Open and Closed Sensors
Before you can arm your system, all protected doors, windows, and other protection zones must be closed or bypassed
(see Force Bypassing, pg. 23). For example, if you leave a protected window open, the system considers it an open
sensor. If a protected window is shut, the system considers it a closed sensor.

Copyright © 2021 Nortek Security & Control LLC
19
REMOTE CONTROL DEVICES
The installer can pair your system with one or more wireless keyfobs to give you the ability to arm/disarm your system
away from, but within range of, the Control Panel using the keyfob’s buttons. The 2GIG EDGE Security & Smart Home
System can be paired to work with a maximum of 32 wireless keyfobs. Depending on your individual needs, keyfobs can
also be congured by the installer to activate specic alarms.
Operate the System with a Keyfob
The installer can congure each keyfob to let you perform up to ve (5) remote
functions:
A Arm the System in Away Mode
»Activate Emergency Alarm (see below)
B Disarm the System
C Arm the System in Stay Mode
D Activate an Auxiliary Function
NOTE: Consult your installer to determine how your keyfob is congured to work with the system. Depending on
your keyfob’s setting, it may or may not be congured to disarm the system.
Arming the System Using a Keyfob
You can arm the system in Stay or Away mode using a keyfob that has been paired with the system.
»To arm the system in Stay Mode, press the Stay button on the keyfob for two (2) seconds.
»To arm the system in Away Mode, press the Away button on the keyfob for two (2) seconds.
NOTE: Depending on setup options, if any perimeter doors or windows are open, the system may not allow arming to
Away mode with a wireless keyfob. Consult your installer to determine how this option is congured on your system.
Disarming the System Using a Keyfob
To disarm the system, press and hold the Disarm button on the keyfob for two (2) seconds.
NOTE: Consult your installer to determine how your keyfob is congured to work with the system. Depending on
the individual keyfob settings, it may or may not be congured to disarm the system.
Activating an Auxiliary Function
To activate an auxiliary function, press and hold the Auxiliary button on the keyfob for two (2) seconds.
NOTE: Consult your installer to determine how your keyfob is congured to work with the system. Depending
on the individual keyfob settings, it may be congured to set off an external siren/sounder or used to activate a
different auxiliary function.
Activating an Alarm Using a Keyfob
To activate an emergency alarm, press and hold both the Away and Disarm buttons on the keyfob for ve (5) seconds.
NOTES:
1 Consult your installer to determine what type of alarm your keyfob is congured to activate. Depending on the
individual keyfob settings, this function might be disabled on your keyfob, or it might be congured to activate
an auxiliary, audible, or silent panic alarm.
2 In order to cancel an emergency alarm activated with a keyfob, you must disarm the system at the 2GIG EDGE
Panel.
3 If Smart Areas is enabled, a keyfob can be congured to perform Arm/Disarm/Alarm functions on one Smart Area.
C
A
D
B
Bypassed Sensors
When sensors are left open, the system cannot be armed unless that sensor is closed (see Open and Closed Sensors,
above) or added to the system’s Bypassed Sensors list. Bypassed Sensors are ones that you intentionally decide to leave
unprotected. See Force Bypassing, pg. 23.
NOTE: Bypassed sensors offer no protection and cannot cause an alarm. Use bypass if you want to arm your
system with one or more sensors open and intentionally unprotected.

2GIG EDGE User Guide 20
CP
ES
DWDC
TH
PIR
CP: CONTROL PANEL
DW: DOOR/WINDOW SENSOR
PIR: MOTION DETECTOR
GB: GLASS BREAK SENSOR
RK: REMOTE KEYPAD
ES: EXTERNAL SIREN
DC: DOORBELL CAMERA
TH: THERMOSTAT
LIVING
DINING
KITCHEN
ENTRY
BATH DEN
GB
BED
DWDW
DW
DW
DW
DW
DW
DW
FRONT AND SIDE DOOR SENSORS
(WITH ENTRY/EXIT DELAY)
DW
BED
DW
GARAGE
GB
RK
PIR
DW
DW
DW
MAIN AND SIDE GARAGE DOOR SENSORS
(WITH ENTRY/EXIT DELAY)
SAMPLE BURGLARY ALARM PLAN
Before the installation, your 2GIG alarm dealer will work with you to design, install, and congure a system intended
to best protect your dwelling. This illustration is an example of a typical residential burglary alarm system offering both
perimeter and interior protection:
Sample Burglary Alarm Plan