3Jtech HSPA FWT WiFi AP User manual

Ver 1.0.0.3
Since 1988
1
Quick Setup Guide for HSPA FWT WiFi AP
1. HSPA FWT WiFi AP Packing List :
Before you start installing the HSPA FWT WiFi AP, please verify that the package contains the
following items:
One Set of HSPA FWT WiFiAP,
1x RJ45 Network Cable,
External 3G Antenna with 3M Antenna Cable,
RJ11 Phone Cable,
1x Power Adapter,
CD with User’s Manual,
This Quick Setup Guide
NOTE: Please notify your sales representative immediately if any items listed above is missing or damaged.
2. Hardware Connection Settings
1) Connect PC to LAN port of your HSPA FWT WiFi AP using a RJ-45 cable.
2) Make sure the SIM card has inserted to the modem, and the modem is ready as well.
3) Connect the power cable to the power connector of your HSPA FWT WiFiAP.
4) For using the Fixed Wireless Terminal (FWT) function, connect an analog phone to the
PHONE port of your HSPA FWT WiFi AP using a RJ-11 cable.
Fig.1 The Connection of HSPA FWT WiFi AP

Ver 1.0.0.3
Since 1988
2
3. LED Description of the Rear Panel
LED Color Status
POWER( ) Yellow Lit when +8V DC power is on and working.
LAN Link ( ) Yellow Lit when the cable connection with device exists.
Flash when the data is transmitting.
Off when no cable connection exists.
WLAN(Wireless LAN )Yellow Lit when the WiFi function is enabled.
Flash when the data is transmitting.
Off when the WiFi function is disabled.
Pick Up/Hang Up ( )Yellow Lit when picking up the connected analog phone.
Off when hanging up the connected analog phone.
SMS( ) Yellow Lit when receiving any new SMS(s).
Off at any status except the incoming of new SMS(s).
3G PPP Status ( ) Yellow Lit when dialup is connected.
Flash when the data is transmitting.
Off when dialup is disconnected.
6 Cellular Signal Strength LEDs
Low ( )
Yellow
All 6 LEDs lit when the signal strength is good.
(The LEDs lit would decrease progressively upon the
signal strength)
Medium ( )
High ( )

Ver 1.0.0.3
Since 1988
3
4. Software Connection Settings
Refer to the following sections to set up the HSPA FWT WiFi AP. Before the setup, please
confirm that the LAN port of the AP has been connected with the PC via RJ-45:
ySet up 3G Settings for the HSPA FWT WiFi AP
1. Please connect your computer to the HSPA FWT WiFiAP’s LAN port.
2. Initiate your Internet Explorer, and type in the address “10.10.10.254”
3. Please input “admin” as the user name and the password. Click OK button to enter
AP’s setup page.
4. Once you are in the setup page, please select “Internet Settings” and enter “WAN”
section of the setup.
5. In 2G/3G ISP SETTINGS, please contact your ISP for the dialup settings. User must
enter Access Point Name (APN),Dial Number, Username and Password. Besides,
you must enter PIN code if you had set up before for the SIM card.
Please ask your ISP for
required information

Ver 1.0.0.3
Since 1988
4
6. Click on Apply after completing the setup. Wait 30 seconds around to have the new
settings taken effect.
7. You can check if the HSPA FWT WiFi AP is online by clicking on the Management /
Status function. The information should be displayed under the Internet
Configurations section.
5. Restore Factory Default Settings
HSPA FWT WiFi AP provides a “RESET” button that will be easy for users to reset the AP to
default. The button is located at the front panel of the AP (See the figure below). Reset steps
are as follows:
(1) Press the RESET button 2 seconds around.
(2) All LEDs on the rear panel will flash 5 times.
(3) The AP will start to reboot.
NOTE: Disconnecting the power before resetting (which takes about 60 seconds) is complete might permanently
destroy the firmware. In this case of a damaged firmware, the unit will need to be replaced by customer
service.
RESET BUTTON