3One data PSE101 Series User manual

PSE101 series
Unmanaged POE Injectors
User manual
Shenzhen 3onedata Technology Co.,Ltd
Tel: [phone] Fax: [phone]
www.3onedata.com
【Introduction】
PSE101 series are Single-port PoE injector, Compliant with
IEEE 802.3af/at PoE Standard, support output power of 15.4W or
30W,Supply power to wireless AP, surveillance cameras, IP phones,
PDAs and other PoE PDs through a single network cable together
with data transmission .Transmission distance up to 100m,Adopt
plug-and-play design, easy to instal, Excellent choice for Wireless
City, Security Surveillance Industry or other network construction.
【Packing List】
Please check the packaging and accessories by your first using.
POE Injectors ×1
AC Power Cord x1
User’s Guide ×1
Certificate of quality ⅹ 1
Warranty card ⅹ 1
【Features】
Compatible with IEEE802.3at(30W) or IEEE802.3af(15.4W),
can supply power to PDs under the two standards
Automatically detects and supplies power to IEEE802.3at or
IEEE 802.3af compliant powered devices(PDs)
Advanced SAFC function,only supply power to IEEE only
supply power to IEEE 802.3af/at compliant PDs
Up to 100m network cable transmitting distance
Special design for free series connection among multiple PoE
injectors
High security performance defending against power surge
【Panel Layout】
Front panel
Back panel
1. Power Indicator
2. POE power Indicator
3. POE port
4. 100M Ethernet Data port
5. AC power input socket
【Dimension】
【Power Input】
PSE101 series provides three power socket rear panel Used in the
AC power input (220 VAC)
【Communication Connector】
PSE101 series provides 1*10/100M POE ports, 1*10/100M ports.
10/100BaseT(X) Ethernet port
The pinout of RJ45 port display as below, connect by UTP or
STP. The connect distance is no more than 100m. 100Mbps is used

120Ωof UTP 5 , 10Mbps is used 120Ωof UTP 3,4,5.
RJ 45 port support automatic MDI/MDI-X operation. can
connect the PC, Server, Converter and HUB .Pin 1,2,3,6
Corresponding connection in MDI. 1→3,2→6,3→1,6→2 are used
as cross wiring in the MDI-X port of Converter and HUB.
10Base-T/100Base-TX are used in MDI/MDI-X, the define of Pin
in the table as below.
NO.
MDI signal MDI-X signal
1 TX+ RX+
2 TX- RX-
3 RX+ TX+
6 RX- TX-
4、5、7、8
— —
Remark：“TX±”Transmit Data±，“RX±”Receive Data±，“—”Not Use。
MDI (straight-through cable)
MDI-X (Cross over cable)
MDI/MDI-X auto connection makes PSE101 series easy to
use for customers without considering the type of network cable.
【LED Indicator】
PSE101 series indictor light on the front panel. the function
of each LED is described in the table as below.
System Indication LED
LED State Description
PWR ON Power is being supplied to power
input PWR input
OFF Power is not being supplied to
power input PWR input
POE
ON POE power supply works.
OFF No POE power supply.
Blinking
The POE port is failed or PD
connection is overloaded, please
remove PDs and reconnect after
checking.
【Installation】
Operation Cautions
1) Don’t stock the device in damp environment or near
water, to avoid water or moisture penetrating into the
inner device.
2) Don’t put the device on a unstable box or desk, the
device will get damaged from falling.
3) Please check and make sure the operation voltage is
meet the voltage standard marked on the device surface
before the next steps.
4) Please use a grounded three-hole power socket in the
rack or desk mounting, to mitigate damage caused by
electro-static discharge or lightning stoke.
5) Keep the device far from heat sources, strong power
radio transmitters and radar transmitters.
6) Similar with other electrical products, the semiconductor
chip in device will get damaged when open and shut off
the power frequently. Please restart the device 3~5
seconds(or longer) after the power is shut off.
7) Please pull out the power plug before cleaning the
device. Don’t wipe the device with wet cloth or clean the
device with liquid.
8) To guarantee a long operation life, the device can only
be used in indoor and in ventilated & dry environment.
And to get a good heat dissipation, please reserve a
space over 10CM around the device.
POE Injector Operation Instruction
1) Connect the provided power cord to AC/IN 90~264V
Socket, PWR LED indicator will be on if the power
connection is successful.
2) Plug the short RJ 45 cable(provided) into “Data/IN”
port of POE injector, the RJ 45 cable connected with a
Ethernet switch on the other end.
3) Connect the “P+D/OUT” port of POE injector to PDs
through another RJ 45 cable( not provided), when the
POE LED indicator is on, the connection is successful.
You can start transmitter power and data together via a
single RJ 45 cable.
Note ：The “POE” LED indicator will be on only
when the “P+D/OUT” port connected with POE
supported PDs.
1 8

【Specification】
Technology:
POE Standard: IEEE802.3af
Ports:
Fixed ports: 2*10/100M Base-T Ports(including one POE ports）
POE Pin-out: 1/2(+)，3/6(-); Customized 4/5(+),7/8(-)
Exchange Properties:
Physic Medium:
10/100Base-TX：UTP category 3/4/5 cables( Maximum 100m)
Network Cable Deployment: Support Auto-MDIX function ，can
automatically identify straight forward cable and cross-over cable
Negotiation Pattern: Support port auto-negotiation
function( automatically negotiate transmission rate and Duplex
modes)
Indicator light:
LED Indicator: Power/PoE Status
Power:
Max Output Power(single port): 15.4W or 30W
Input Power Supply:
PSE101-15W:90～264VAC/50～60Hz/15W
PSE101-30W:90～264VAC/50～60Hz/30W
Working Environment:
Operation Temperature: -20~50°C
Storage Temperature: -40~70°C
Operation Humidity:10%～90%(non-condensing)
Storage Humidity:5%～95%(non-condensing)
Mechanical Properties:
Weight: 200g
Dimensions（L×W×H）:145*65*44mm
Warranty:
Warranty time: 3 years