agiliti NP Trio User manual

NP Trio™
User Manual
MFG-0021ZL-0523
Doc. #: ____________ Rev. Date: ____________ Rev.: ______
IFU0000079 05/29/2023 1.0

2
Table of Contents
Introduction ...................................................................................................................................3
Product Description...............................................................................................................3
Intended Use...........................................................................................................................3
General Information...............................................................................................................3
Product at a Glance......................................................................................................................4
Symbols ..........................................................................................................................................5
Labels..............................................................................................................................................6
Safety Instructions.........................................................................................................................8
Seven Zones of Bed Rail Entrapment .................................................................................8
Electrical Shock Hazards .....................................................................................................10
Warnings................................................................................................................................10
Cautions.................................................................................................................................10
General Notes.......................................................................................................................11
Specifications: NP Trio™.......................................................................................................... 12
Unpacking Instructions ............................................................................................................. 13
Set-Up Instructions .................................................................................................................... 13
Cleaning Instructions................................................................................................................. 14
Top Cover..............................................................................................................................14
Bottom Cover........................................................................................................................15
Preventive Maintenance ........................................................................................................... 16
Storage and Disposal................................................................................................................ 16
Limited Product Warranty......................................................................................................... 17

3
Introduction
Product Description
The NP Trio™ non-powered support surface can accommodate diverse patient body
types and patient weights. The multi-layered design ensures proper weight dispersal and
maximizes pressure redistribution. The surface and components are designed to
eliminate harmful chemicals of concern in the fabric, fire barrier and foam. All versions use
a laminated high-density foam core. The sloped heel section aids in patient comfort and
pressure injury prevention.
Intended Use
The 3-layered foam support surface will provide pressure redistribution to prevent and
treat pressure injuries. The product is intended for use on a Medical Bed Frame in a
medical facility by trained personnel.
General Information
— An authorized user is defined as an adult.
— Read and completely understand the manual before use.
— DO NOT modify this equipment without authorization from the manufacturer.
— Only use Agiliti replacement covers that are specific to this product.
— At certain intervals, maintenance of this product is required and must be performed by
authorized personnel only.
— Retain this manual for future use and maintenance.
— Users should be risk assessed to ensure they are able to understand this manual and make
use of this product without risk to themselves or others.
Symbols, definitions and fonts are used throughout this manual to aid user readability
and understanding of content.
— Standard Text: Used for regular information.
— Bold Text: Emphasizes a word or phrase.
— NOTE: Sets apart special information or important instruction clarification.

4
Product at a Glance
NP Trio™
Support Surface Size (W x L) 7” Height

5
Symbols
Symbol Description
Follow User Manual:
Indicates mandatory action to read and fully understand these
instructions prior to use.
Accompanying Documents:
Read and fully understand all accompanying documents for NP Trio™
before use.
Electrical Shock Hazard Warning:
Symbol alerts user to the presence of electrical shock hazards. It is
important to follow all instructions and special procedures to avoid
electrical shock to the operator, caregiver, and/or patient.
Contraindication:
Symbol alerts user to possible condition or circumstance which makes a
particular treatment or procedure potentially inadvisable. Disregarding a
contraindication could result in patient and/or user injury, as well as
damage to equipment.
Warning/Caution:
Symbol alerts user to the presence of important operating, maintenance,
or servicing instructions. Disregarding a warning could result in patient
and/or user injury, as well as damage to equipment.

6
Labels
Label Description
Top Cover Screen Print
Cleaning and Care Label
Law Label
Flammability Standard Compliance Label
16 CFR Part 1632
16 CFR Part 1633
Technical Bulletin 117-2013 Compliance Label
TB117

7
UDI Label
Part Number / Lot # Label

8
Safety Instructions
WARNING: Bed rail entrapment is a serious health risk that can result in
serious injury or even death. Agiliti recommends the care provider be mindful
of the FDA guidelines relevant to bed rail entrapment, as serious injury can
result. These guidelines can be found on the FDA website. When using a foam
or air therapy system the care provider is responsible for ensuring the support
surface properly fits the bed frame. It is also the care provider’s ultimate
decision whether or not to use bed rails with the patient.
Seven Zones of Bed Rail Entrapment
If the patient would have any clinical conditions that could result in risk of falling or
improperly lying-in bed, the bed should be left at its lowest setting and in flat position
when not attended. Agiliti recommends the use of bed rails if they are available. There
are seven zones of bed rail entrapment.

9
Safety Instructions
Only authorized users should install the NP Trio™ support surface on bed frames. A thorough
understanding of the bed frame user manual is required prior to use. Follow the instructions
contained in this manual carefully. Use NP Trio only if it is in proper working order and free
from tears or punctures. The terms Warning and Caution are used frequently throughout this
manual. A clear and concise understanding is required of these two terms.
CONTRAINDICATION: Indicates important information that may be
contradictory to the product instructions, which if not understood, could cause
serious injury.
ELECTRICAL SHOCK HAZARD WARNING: This symbol is intended to alert
the user to the presence of electrical shock hazards. It is important to follow all
instructions and special procedures to avoid electrical shock to the operator,
care provider, and/or patient.
WARNING: Indicates a potentially dangerous situation, which if not avoided,
could result in injury ranging from moderate to serious severity up to and
including death.
CAUTION: Indicates a potentially dangerous situation, which if not avoided,
could result in injury ranging from minor to moderate severity.

10
Electrical Shock Hazards
ELECTRICAL SHOCK HAZARD WARNING: To avoid risk of electric shock or Injury,
ensure all cords on bed frame are away from bed deck prior to installing product.
ELECTRICAL SHOCK HAZARD WARNING: Before any cleaning and
disinfection procedures are performed, unplug all power cords in proximity to
product to eliminate possibility of electrical shock.
Warnings
WARNING: To avoid serious injury or death, ensure product is used with
compatible bed frame sizes.
WARNING: To avoid serious injury or death, ensure product is properly retained on
bed frame to avoid slippage or unintended movement.
WARNING: Product is to be used in accordance with each facility’s policies
and procedures.
WARNING: Do not exceed Max Patient Weight listed in the specifications. Can
lead to injury or damage
WARNING: Bed rail entrapment can result in serious injury or even death.
Agiliti recommends caregivers be mindful of the FDA guidelines relevant to
bed rail entrapment. These guidelines can be found on the FDA website as
referenced below. When using a replacement support surface, the caregiver is
responsible for ensuring the product properly fits the bed frame. It is also the
caregiver’s decision whether or not to use bed rails with the patient.
Cautions
CAUTION: Use only approved replacement parts or covers.
CAUTION: Use of product is only one element of care in the prevention and
treatment of pressure injuries. Frequent repositioning, proper care, routine
skin assessment, wound treatment and proper nutrition are but a few of the
elements required in the prevention and treatment of pressure injuries. The
responsibility of prevention and treatment of pressure injuries lies with the
health care professional.
CAUTION: Ensure that product covers are free from tears, rips or damage from
shipping and handling prior to installing on bed frame.
CAUTION: It is recommended that gloves and protective clothing be worn at
all times during cleaning and disinfecting.
CAUTION: Product requires regular maintenance to ensure performance and
avoid premature wear, damage and injury.

11
General Notes
NOTE: Only the outer cover requires cleaning and maintenance. Disassembly of the
support surface for maintenance of internal components is not recommended. Do not use
harsh solvents or cleaners. Special care should be used to not puncture product with
needles or sharp instruments. This may result in loss of integrity of the cover or internal
components.
NOTE: To ensure that approved chemical agents are being used for the top and bottom
covers, visit agilitihealth.com/approvedsurfacecleaners.

12
Specifications:
NP Trio™
NP Trio
Support Surface
Height x Length
Max Patient
Weight*
35”W
(89cm)
7”H x 82”L (17.5cm x 208cm)
7”H x 84”L (17.5cm x 213cm)
7”H x 82”L Extendable to 88L
(17.5cm x 208cm to 223cm)
500 lb.
(227 kg)
NP Trio BH™
Behavioral Health Support Surface** Height x Length
Max Patient
Weight*
35”W (89cm)
7”H x 82”L (17.5cm x 208cm)
500 lb.
(227 kg)
39”W (99cm)
7”H x 82”L (17.5cm x 208cm)
700 lb.
(318 kg)
NP Trio EX™
Support Surface Height x Length
Max Patient
Weight*
35”W Expandable to 42”W
(99cm to 107cm)
7”H x 80”L (17.5cm x 203cm)
7”H x 84”L (17.5cm x
213cm)
700 lb.
39”W Seamless Expandable
to 48”W
(99cm to 122cm)
7”H x 82”L (17.5cm x 213cm)
7”H x 82”L Extendable to 88L
(17.5cm x 208cm to 223cm)
700 lb. to 1000 lb.
* NOTE: Max Patient Weight capacity of support surface is not to exceed bed frame Safe
Working Load.
** NOTE: Support Surface available with Defined Perimeter
NP Trio Components Material Features
Top Cover Polycarbonate
4-way stretch, breathable
Antimicrobial
Bottom Cover 200D Laminated TPU
Hi-friction nonslip
Foam Core Tri-laminated Polyurethane Foam
with CuPro™ Visco Foam Topper Heel Slope
Core Shield™ Stretch Polyurethane film Flexible foam core
protection

13
Unpacking Instructions
Caution: Ensure that support surface covers are free from tears, rips or
damage from shipping and handling prior to installing on bed frame.
1. Remove products from packing materials and examine for shipping damage
. Notify
Agiliti immediately upon discovery of damage.
a. If delivered by a freight company: note a description of the damage on the
carrier’s bill of lading and take photos for your records. Depending on the
shipping arrangement, the obligation to prepare, file, and pursue any claim for
any damage or loss may be on the shipping recipient (or buyer).
b. If delivered by an Agiliti employee: please reach out to your local contact to
initiate the process.
2. If replacement parts are needed, contact Agiliti Customer Service.
3. Remove packaging surrounding product.
Set-Up Instructions
WARNING: Bed rail entrapment can result in serious injury or even death. Agiliti
recommends caregivers be mindful of the FDA guidelines relevant to bed rail
entrapment. These guidelines can be found on the FDA website as referenced
below. When using a replacement support surface, the caregiver is responsible
for ensuring the product properly fits the bed frame. It is also the caregiver’s
decision whether or not to use bed rails with the patient.
CAUTION: Use of product is only one element of care in the prevention and
treatment of pressure injuries. Frequent repositioning, proper care, routine skin
assessment, wound treatment and proper nutrition are but a few of the
elements required in the prevention and treatment of pressure injuries. The
responsibility of prevention and treatment of pressure injuries lies with the
health care professional.
CAUTION: Ensure that support surface covers are free from tears, rips or
damage from shipping and handling prior to installing on bed frame.
1. Verify that product is the correct size for bed frame top deck. Refer to Siderail
Entrapment Guidelines (see Table of Contents).
2. Place bed frame in a flat position.
3. Install product with the sloped heel section toward the foot of the bed.
4. Disinfect product prior to patient use. Refer to Support Surface Cleaning Instructions
(see Table of Contents).

14
Cleaning Instructions
ELECTRICAL SHOCK HAZARD WARNING
: Before any cleaning and
disinfection procedures are performed, unplug all power cords in proximity to
product to eliminate possibility of electrical shock.
CAUTION: It is recommended that gloves and protective clothing be worn at all
times during cleaning and disinfecting.
CAUTION: Product requires regular maintenance to ensure performance and to
avoid premature wear, damage and injury.
NOTE: Only the outer cover of product requires cleaning and maintenance. Disassembly of
the support surface for maintenance of internal components is not recommended. Do not use
harsh solvents or cleaners. Special care should be used to not puncture the support surface
with needles or sharp instruments. This may result in loss of integrity of the support surface
cover or internal components.
NOTE: To ensure that approved chemical agents are being used for top and bottom covers,
visit agilitihealth.com/approvedsurfacecleaners.
DO NOT autoclave.
NOTE: Improper cleaning, rinsing or the incorrect use of cleaning agents can lead to
premature fabric discoloration and breakdown of the fabric’s fluid resistance, stain resistance
and fabric strength.
Top Cover
The top cover material is resistant to a wide variety of hospital cleaners and resists breakdown
with disinfectants and cleaners based on chlorine, alcohol, peroxide, quaternary ammonium,
chloramine and phenol. Personal Protective Equipment (PPE) should always be used as
directed by the disinfectant’s Material Safety Data Sheet.
1. Prepare the disinfectant according to the manufacturer’s recommendations.
2. Prepare a separate bucket of warm, fresh water to be used for rinsing the equipment
after cleaning/disinfecting procedures are completed as instructed.
3. All exterior areas of the top cover are to be wiped using a cloth dampened with the
disinfectant, prepared as directed by the manufacturer’s recommendations, to remove
organic material and visible soil.
4. Allow the support surface shell to remain wet with disinfectant solution for the
manufacturer’s recommended contact time, and no longer.
5. Immediately after recommended contact time, rinse all surfaces of product with fresh
water and clean cloth to remove chemical and organic residue.
6. Stains on the top cover may be treated using an approved stain remover, according to
the manufacturer’s recommendations.
-No Abrasives: Abrasive cleaners and abrasive cleaning devices (scouring sponges) will
dramatically reduce the life of the top cover.
-Do Not Use Solvents.

15
-Follow dilution recommendations: One of the most significant errors in cleaning support
surface top cover is not diluting a cleaner according to manufacturer recommendations.
Most surface cleaners are sold in concentrated forms and are intended to be diluted,
usually with a large percentage of water. Failing to do this can shorten the life of the
support surface top cover significantly.
-Rinse after using a cleaning agent: When you wipe across a surface with a
cleaner/chemical strong enough to kill bacteria, you must rinse afterward. Leaving the
cleaner to dry on the surface will shorten the lifespan of the top cover.
NOTE: If additional cleaning is necessary, top cover may be removed and laundered using
standard hospital disinfectant/detergent. DO NOT use temperatures in excess of 170°F (76°C).
NOTE: After washing, the top cover is to be air dried or in a dryer at very low or no heat to
protect it from heat-related damage.
1. Set washing machine to Regular Cycle.
2. Pre-soak with disinfectant/detergent in cold water for 10 minutes. DO NOT USE
HARSH SOLVENTS OR CLEANERS.
3. Main wash cycle: 15 minutes (time dependent on soil level).
4. Rinse cycle: 5 minutes, minimum.
5. Spin/Drain cycle: 5 minutes, minimum
Bottom Cover
1. Prepare the disinfectant according to the manufacturer’s recommendations.
2. Prepare a separate bucket of warm, fresh water to be used for rinsing the equipment
after cleaning/disinfecting procedures are completed as instructed.
3. All areas of the bottom cover are to be wiped using a coarse cloth dampened with the
disinfectant, prepared as directed by the manufacturer’s recommendations, to remove
organic material and visible soil.
4. Allow the bottom cover to remain wet with disinfectant solution for the manufacturer’s
recommended contact time, and no longer.
5. Immediately after recommended contact time, rinse all areas of the bottom cover with
fresh water and a clean cloth to remove chemical and organic residue.
6. Stains on the bottom cover may be treated using an approved stain remover,
according to the chemical manufacturer’s recommendations.
7. After washing, the bottom cover must be allowed to airdry

16
Preventive Maintenance
CAUTION: It is recommended that gloves and protective clothing be worn at all
times during cleaning and disinfecting.
CAUTION: Preventive maintenance should not be attempted while equipment is in
use.
NOTE: To keep equipment working efficiently and effectively for an extended time, it is
essential to make sure the equipment is cleaned regularly and well maintained.
Check the items on this chart at the indicated intervals. If any of the items are loose, worn, or
damaged, immediately have them replaced.
Place product on flat, clean and level surface and inspect for damage, wear, punctures, rips
and/or tears on the following components:
Components Inspect for
During cleaning
and disinfecting
Annually
Top Cover
Damage, wear, punctures, rips
and or tears X X
Bottom Cover Damage, wear, punctures, rips
and or tears X X
Core Shield™ Damage, wear, punctures, rips
and or tears X X
Foam Core Remove covers and inspect for
fluid ingress N/A X
Storage and Disposal
Always store product on a clean, level surface.
Avoid storage of other equipment on top of product.
End-of-life Agiliti products must be disposed of properly according to local laws and
regulations. Please contact Agiliti or your local authorities for disposal and recycling
options.

17
Limited Product Warranty D-L00-001 Rev. 4
NP Trio™
PLEASE READ THESE WARRANTY TERMS AND CONDITIONS CAREFULLY BEFORE
USING YOUR AGILITI PRODUCT. BY USING THEPRODUCT, YOU ARE CONSENTING
TO BE BOUND BY THE FOLLOWING WARRANTY TERMS AND CONDITIONS.
Limited Warranty
Raye’s, Inc dba Sizewise Manufacturing (“Sizewise Manufacturing”) warrants the above
referenced product to be free from material defects in materials and workmanship for the
warranty periods set forth below when the product is used and serviced properly in
accordance with the specifications set forth in the Agiliti user manual in effect at the time of
sale of the product, including without limitation the safety instructions and if applicable the
safe working load and weight limitations set forth therein. If there is no period of time
specified below, the warranty period shall be ninety (90) days. Unless agreed to otherwise in
writing by Sizewise Manufacturing, the warranty periods commence on the invoice date of
the original purchase. This warranty applies only against defects discovered within the
warranty period and extends only to you, the Buyer. As used in this warranty Buyer means
the original purchaser or original end user of the product designated at the time of purchase.
Any reference to “you” is as the Buyer. Parts repaired or replaced under the terms of this
warranty will be warranted for the remainder of the original warranty period only. Buyer is
solely responsible for determining whether the products and services offered by Sizewise
Manufacturing are appropriate for its intended use including use by Buyer’s employees,
invitees, contractors, representatives, third party beneficiaries, or any other person Buyer
intends to use the product. Buyer acknowledges it has made the selection of the products
based upon its own judgment and that the product is of a size, design, capacity, condition,
quality, and durability selected by Buyer. Buyer expressly disclaims any reliance upon any
statements or representations made by Sizewise Manufacturing or any other party on its
behalf except as otherwise specifically provided for in this Limited Product Warranty. Buyer
acknowledges and agrees that the remedy in this warranty for the repair and replacement of
defective product or part(s) shall constitute the sole remedy in the event of a defective
product or part(s).
THE WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER
RIGHTS THAT VARY FROM STATE TO STATE. Sizewise Manufacturing’s obligations under
this warranty are limited as set forth below.
Warranty Period and Coverage:
Product
Internal
Components Top Cover
Core
Shield™
RF-Welded
Seams
NP Trio
5 Years 4 Years 4 Years 4 Years

18
Limited Product Warranty D-L00-001 Rev. 4
Conditions and Restrictions
This warranty is valid only in accordance with the conditions set forth below:
The warranty applies to this product only while:
—
it remains in the possession of the Buyer and proof of purchase is demonstrated,
— it has not been subjected to accident, misuse, abuse, improper service, or modification,
— Claims are made within the warranty period.
— This warranty does not apply to any other products or devices sold separately regardless of whether
used with this product. Such other products or devices, to the extent sold with a warranty, will be
subject to the separate limited product warranty set forth in the user manual for such product or
device.
— Sizewise Manufacturing’s sole liability shall be discharged by replacing or repairing, at Sizewise
Manufacturing’s option, the product or its part or parts which are determined by Sizewise
Manufacturing to be defective under normal and proper use during the warranty period.
— Buyer shall notify Sizewise Manufacturing or the authorized Sizewise Manufacturing dealer
immediately but in no event more than seven (7) days after the date of discovery of any alleged
defect by contacting Sizewise Manufacturing Parts and Service at 800-814-9389 Monday through
Friday 8am–5pm local time.
— If the product or part should be returned to Sizewise Manufacturing, a return authorization number
(RA#) must be obtained by Buyer from Sizewise Manufacturing.The RA# will be valid for 21 days from
the date it is issued.
— Buyer is responsible for any shipping, freight, handling, pickup, or delivery charges or fees
including without limitation any expediting fees involved with the delivery of the defective product
or parts to Sizewise Manufacturing’s factory for repair or replacement.
— If on-site technical service is required, as determined by Sizewise Manufacturing, a service
representative will be dispatched during Sizewise Manufacturing’s standard service hours Monday
through Friday 8am-5pm local time, provided the product is located within Sizewise Manufacturing’s
service territory.
— If Sizewise Manufacturing determines the problem with the product or part(s) is a result of defective
material or workmanship, the product or part will be replaced or repaired at the discretion of
Sizewise Manufacturing, and at no charge to the Buyer; however, this is subject to the limitations and
exclusions of this Limited Product Warranty.
— At the election of Sizewise Manufacturing, replacement parts may be new or refurbished; Sizewise
Manufacturing reserves the right to substitute materials if original materials are no longer available.
— If Sizewise Manufacturing determines the product or part that Buyer has requested warranty
services on are not covered by the warranty for any reason including, without limitation, because it is
outside of the warranty period, excluded from the warranty, or the warranty is void, Buyer shall pay
for the repair or replacement services, including parts and labor performed by Sizewise
Manufacturing at Sizewise Manufacturing’s prevailing time and material rates plus freight and
delivery.
— If Buyer declines the repair or replacement service upon notice from Sizewise Manufacturing that it is
not covered under warranty, Buyer shall reimburse Sizewise Manufacturing for all costs from
investigating and responding to Buyer’s request.
— Any costs to Buyer as referred to herein shall be at Sizewise Manufacturing’s prevailing time and
material rates plus any freight and delivery charges incurred by Sizewise Manufacturing.
— Any assistance provided by Sizewise Manufacturing outside the terms of this warranty does not waive the
limits of this warranty.
— Sizewise Manufacturing does not pay labor outside the United States.
— Any description of the products is for identification purposes only and is not an express warranty.
— Loaned products, demo or sample products, and/or consumable products including without limitation
batteries and sheets are furnished to Buyer on an “AS IS WITH ALL FAULTS” basis.

19
Limited Product Warranty D-L00-001 Rev. 4
EXCLUSIONS AND LIMITATIONS
This Limited Product Warranty shall not apply to the below listed events, occurrences, actions and/or items.
Sizewise Manufacturing and its affiliates, shall have no obligation to make repairs, replace, or correct
products including any part or parts of the product as the result of Sizewise Manufacturing’s determination of
any of the following:
— Software (PROM) or firmware version upgrades or updates or any other changes and/or any outages,
interruptions, delays, attacks, malware, or any other technology or viruses on such software or firmware
or Buyer’s network, if applicable to this product.
— Normal wear and tear of the product including, without limitation, normal discoloring, body
impressions on mattresses or loss in some resiliency, if applicable to this product, and/or any
cosmetic items, consumable items including, without limitation, mattresses, casters, sheets,
handsets, and batteries as these items are not covered by this warranty.
— Damage due to improper transport, storage, installation, maintenance, use, repair, or failure to follow
Sizewise Manufacturing’s or its authorized representative’s instructions or procedures as detailed in the
user manual.
— Damage or malfunctions resulting from work performed by service providers not authorized by Sizewise
Manufacturing.
— Repairs performed on the product or parts missing a serial number or with a serial tag that has been
altered, tampered with, or defaced in any manner.
— Service calls to correct installation of the product, unless installed under contract by Sizewise
Manufacturing, its affiliate, or authorized representative. The terms of the service contract only shall
apply to service installation corrections, not this warranty.
— Shipping, freight, handling, pickup, and delivery charges or fees involved with delivery of the products
and or part(s) to Sizewise Manufacturing’s factory for repair or replacement and returning the
replacement or repaired products and/or parts to Buyer.
— Any labor costs incurred beyond the applicable labor warranty period.
— Damage or product failure from causes external to the product or part(s) including, without
limitation, power or electric failure or surges, electrical wiring not in compliance with electrical
codes, or specifications set forth in the user manual containing this limited product warranty.
— Damage caused by failure to provide reasonable and necessary maintenance as outlined in the user
manual.
— Damage caused by the use, misuse, negligence, loss, or abuse of the product or any parts by Buyer,
including without limitation any third-party beneficiaries, end user, caregivers, patients, or any
others that Buyer intends to use the product, except Sizewise Manufacturing or an authorized
Sizewise Manufacturing service provider, including, without limitation:
o
exceeding any specified weight limitations in any product documentation such as the
user manual and, including without limitation as applicable to the product, the Safe
Working Load, Maximum Patient Weight, and/or Maximum Load as those terms are
defined in the product documentation, user manual and by applicable regulations,
o
to the extent the product specifies a minimum load/weight criteria including without
limitation a Minimum Patient Weight in order for it to function property, then any use
not in compliance therewith.
o cleaning upholstery or fabrics with harsh chemicals, or bleach, outside the
recommended cleaning guidelines,
o
altering, tampering with, or modifying in any manner without the express written
consent of Sizewise Manufacturing any part(s) or structural components or
appurtenances of the products,
o
use of the product or part(s) in any manner for which it is not designed or in any manner
inconsistent with the information set forth in the user manual, including, without
limitation, use with other devices, accessories, cables or ancillary products including
without limitation inappropriate replacement parts and/or repairs, for which it was not
intended.

20
Limited Product Warranty D-L00-001 Rev. 4
— Exposure of the product or part(s) to accident, acts of God, or natural causes (such as natural
disasters, fire, flood, wind, water or power failures, or any acts or threats of terrorism, both domestic
and foreign) whether foreseen or unforeseen.
— Operation of the product beyond its normal useful life.
— Buyer’s failure to show proof of purchase.
— Products or items not manufactured by Sizewise Manufacturing. Rather, for products or items
obtained by Sizewise Manufacturing from an original manufacturer or third-party supplier, Sizewise
Manufacturing may assign to the Buyer any warranty rights in such products or items that Sizewise
Manufacturing may have from the original manufacturer or third-party supplier to the extent such
assignment is allowed by the original manufacturer or third-party supplier.
Disclaimer and Release
The warranties provided herein are the exclusive warranties given for the product and supersede
any prior, contrary, or additional representations or warranties, whether oral or written. TO THE
EXTENT NOT PROHIBITED BY LAW, THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER
WARRANTIES, ORAL, WRITTEN, STATUTORY, EXPRESS OR IMPLIED. EXCEPT FOR THE EXPRESS
WARRANTIES IN THIS LIMITED PRODUCT WARRANTY AND TO THE EXTENT NOT PROHIBITED BY
LAW, SIZEWISE MANUFACTURING DISCLAIMS ANY AND ALL OTHER WARRANTIES WHETHER
EXPRESS OR IMPLIED WARRANTIES, STATUTORY OR OTHERWISE, INCLUDING, WITHOUT
LIMITATION, ANY WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE
OR NON-INFRINGEMENT, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING, USAGE
OF TRADE, OPERATION OF LAW, OR OTHERWISE WITH RESPECT TO ANY PRODUCT, SERVICES,
PARTS INCLUDING REPAIRED OR REPLACED PRODUCTS AND PARTS ARE HEREBY DISCLAIMED
AND EXCLUDED . SIZEWISE MANUFACTURING ALSO HEREBY DISCLAIMS AND EXCLUDES ALL
OTHER OBLIGATIONS OR LIABILITIES, EXPRESS OR IMPLIED, ARISING BY LAW OR OTHERWISE,
WITH RESPECT TO ANY NONCONFORMANCE OR DEFECT IN ANY PRODUCT OR PART(S),
INCLUDING BUT NOT LIMITED TO: (A) ANY OBLIGATION, LIABILITY, RIGHT, CLAIM, OR REMEDY
IN TORT, WHETHER OR NOT ARISING FROM THE NEGLIGENCE OF SIZEWISE MANUFACTURING
INCLUDING ITS PARENT, SUBSIDIARY OR AFFILIATE COMPANIES, EMPLOYEES, AGENTS,
PARTNERS, AUTHORIZED DEALERS, OTHER REPRESENTATIVES AND/OR ITS SUPPLIERS
(WHETHER ACTIVE, PASSIVE, OR IMPUTED); AND (B) ANY OBLIGATION, LIABILITY, RIGHT, CLAIM,
OR REMEDY FOR LOSS OF OR DAMAGE TO ANY PRODUCT OR PART(S) . This disclaimer and
release shall apply even if the express warranty set forth above fails of its essential purpose. SOME
STATES DO NOT ALLOW DISCLAIMERS OF IMPLIED WARRANTIES, SO THIS DISCLAIMEER MAY
NOT APPLY TO YOU. TO THE EXTENT SUCH WARRANTIES CANNOT BE DISCLAIMED UNDER THE
LAWS OF YOUR JURISDICTION, SIZEWISE MANUFACTURING LIMITS THE DURATION AND
REMEDIES OF SUCH WARRANTIES TO THE DURATION OF THIS EXPRESS
LIMITED WARRANTY.
Exclusive Remedies
For any product described above that Sizewise Manufacturing determines to have failed to conform to this
limited warranty, Sizewise Manufacturing will provide, at its option, one of the following:
1. Repair.
2. Replacement; or
3. Refund of the purchase price.
Sizewise Manufacturing Limited Product Warranty service may be obtained by contacting Sizewise
Manufacturing or the authorized dealer from whom Buyer purchased the item. Sizewise Manufacturing
compensates only Sizewise Manufacturing-authorized service providers for warranty trips within their
normal service area to repair commercial products at the customer’s location.
THESE SHALL BE THE SOLE AND EXCLUSIVE REMEDIES OF THE BUYER FOR ANY BREACH OF
WARRANTY.