3One data ES208G User manual

ES208G
Unmanaged Ethernet Switch Quick
Installation Guide
3onedata Co., Ltd.
Address:
3/B, Zone 1, Baiwangxin High Technology
Industrial Park, Xili, Nanshan District,
Shenzhen
Website:
www.3onedata.com
Te l :
[phone]
Fax:
[phone]
【
Package Checklist
】
Please check whether the package and accessories are intact
while using the switch for the first time.
1.
Industrial Ethernet switch
2.
Certification
3.
Quick installation guide
4.
Warranty card
5.
DIN-Rail mounting attachment
If any of these items are damaged or lost, please contact our
company or dealers, we will solve it ASAP.
【
Product Overview
】
The product is 8-port full Gigabit layer 2 unmanaged Ethernet
switch. Model as follows: ES208G (8 Gigabit copper ports).
【
Panel Design
】
Top view, Bottom view and Rear view
Front view and Side view
1. Grounding screw (protective grounding)
2. Power input terminal block
3. DIN-Rail mounting kit
4. 10/100/1000Base-T(X) Ethernet port
5. PWR indicator
6. Ethernet port connection or active status indicator
【
Mounting Dimension
】
Unit: mm
Attention before mounting:
Don't place or install the device in area near water or
moist, keep the relative humidity of the device
surrounding between 5%~95% without condensation.
Before power on, first confirm the supported power
supply specification to avoid over-voltage damaging the
device.
The device surface temperature is high after running;
please don't directly contact to avoid scalding.
【
DIN-Rail Mounting
】
For convenient usage in industrial environments, the product
adopts 35mm DIN-Rail mounting, mounting steps as below:

Check whether the DIN-Rail mounting kit thatStep 1
comes with the device is installed firmly.
Insert the bottom of DIN-Rail mounting kit (one sideStep 2
with spring support) into DIN-Rail, and then insert
the top into DIN-Rail.
Tips:
Insert a little to the bottom, lift upward and then insert
to the top.
Check and confirm the product is firmly installed onStep 3
DIN-Rail, and then mounting ends.
【
Disassembling DIN-Rail
】
Power off the device.Step 1
After lift the device upward slightly, first shift out theStep 2
top of DIN-Rail mounting kit, and then shift out the
bottom of DIN-Rail, disassembling ends.
Attention before powering on:
Power ON operation: first connect power line to the
connection terminal of device power supply, and then
power on.
Power OFF operation: first unpin the power plug, and
then remove the power line, please note the operation
order above.
【
Power Supply Connection
】
DC power supply
The device provides 3 pins 7.62mm
pitch terminal blocks. The power
supply supports nonpolarity and
anti-reverse connection. It can
normally operate after reverse connection. Power supply
range: 12～48VDC
【
Checking LED Indicator
】
The function of each LED is described in the table as below:
LED
Status
Description
PWR ON PWR is connected and running
normally
OFF
PWR is disconnected and running
abnormally.
Link/Act
(G1-G8)
ON
Ethernet port connection is active.
Blinking
Data transmitted
OFF
Ethernet port connection is inactive.
【
Specification
】
Panel
Gigabit copper port
10/100/1000Base-T(X)
self-adapting RJ45 port, full/half
duplex self-adaption, support
MDI/MDI-X self-adaption
Indicator Power indicator, interface
indicator
Exchange attributes
Backplane bandwidth
20G
Packet buffer size
2.5Mbit
MAC table size
8K
Power supply
Input power supply
12~48VDC
Support nonpolarity and
anti-reverse connection
Support built-in overcurrent 4.0A
protection
Access terminal 3 pins 7.62mm pitch terminal
blocks
Consumption
No-load
0.82W@24VDC
Full-load
3.65W@24VDC
Environmental Limits
Working temperature
-25
℃
~70
℃
Storage temperature
-40
℃
~85
℃
Working humidity
5%~95% (no condensation)
Protection grade
IP40 (metal shell)