3One data ICPE2600 Series User manual

ICPE2600 Series Industrial
Outdoor 5G Wireless Router
Quick Installation Guide
3onedata Co., Ltd.
Address: 3/B, Zone 1, Baiwangxin High Technology
Industrial Park, Xili, Nanshan District,
Shenzhen
Website: www.3onedata.com
Tel : [phone]
Fax: [phone]
【Package Checklist】
Please check whether the package and accessories are intact
while using the device for the first time.
1.
5G Router
2.
Pole/wall mounting attachment
3.
Warranty card
4.
Certification
If any of these items are damaged or lost, please contact our
company or dealers, we will solve it ASAP.
【Product Overview】
This series product is Industrial 5G Wireless Router. Models
as follows:
Model I. IAP2600-BW-8A25-2GT-PDP12_48 (1 Gigabit PoE
WAN + 1 Gigabit LAN + 2 2.4G antenna interfaces
+ 2 5.8G antenna interfaces + 4 5G Sub-6G
antenna interfaces )
Model II. IAP2600A-BW-8A25-2GT-PDP12_48 (1 Gigabit
PoE WAN + 1 Gigabit LAN + 2 2.4G antenna
interfaces + 2 5.8G antenna interfaces + 4 5G
Sub-6G antenna interfaces )
【Panel Design】
Front View
Rear View
Top view and bottom view
Left view and right view

1. Wall Mounting or Pole Mounting location hole
2. 5.8G antenna interface
3. 5G Sub-6G antenna interface
4. 2.4G antenna interface
5. 10/100/1000Base-T(X) LAN port
6. Terminal block for power input
7. Grounding screw
8. 10/100/1000Base-T(X) PoE WAN port (PoE input)
9. SIM card slot (SIM1, SIM2)
10. Reset button
11. Running indicator (RUN)
12. WLAN indicator (WLAN)
13. 5G Indicator (5G)
14. Gigabit WAN indicator (WAN)
15. Gigabit LAN indicator (LAN)
16. 5G signal strength indicator（ ）
17. Breather valve
【Mounting Dimension】
Unit: mm
Notice Before Mounting:
Don't place or install the device in area near water or
moist, keep the relative humidity of the device
surrounding between 5%~95% without condensation.
Before power on, first confirm the supported power
supply specification to avoid over-voltage damaging the
device.
The device surface temperature is high after running;
please don't directly contact to avoid scalding.
【Pole-mounted Device Mounting】
Step 1 Use 4 M6 screws to install the clamp board as
shown in the figure below on the device backboard.
Step 2 Align the other clamp board with the hole center
line of the installed clamp board, then place the
support pipe to align the hole center of the two
clamp boards. When the two clamps are docking, it
can choose 15° or 90° installation angle.
Step 3 Pass the M6 long screw through the hole where the
clamp boards are docked and the support pipe, and
tighten the corresponding M6 nut.
Step 4 Install U-shaped derrick screws and derrick teeth
on the clamp board, and put the derrick with a
diameter of 40 mm - Ф Ф 50 mm in an U-shaped
slot, as shown in the figure below.
Step 5 Adjust device position and tighten the derrick nut to
fix the position of the device on the derrick.
Installation ends.

【Pole-mounted Device Disassembling】
Step 1 Device power off.
Step 2 Stabilize the device, unscrew the U-shaped derrick
nut and take out the U-shaped derrick screw.
Step 3 Take out the device, disassembling ends.
【Wall Mounting】
Step 1 Use 4 M6 screws to install the clamp board as
shown in the figure below on the device backboard.
Step 2 Align the other clamp board with the hole center
line of the installed clamp board, then place the
support pipe to align the hole center of the two
clamp boards. When the two clamps are docking, it
can choose 15° or 90° installation angle.
Step 3 Pass the M6 long screw through the hole where the
clamp boards are docked and the support pipe, and
tighten the corresponding M6 nut.
Step 4 Pass the M6 screw through the location hole of the
clamp board. The size of location hole of the clamp
board is as shown below.
Step 5 Install the device on the wall and tighten the screw.
Installation ends.
【Wall-mounted Device Disassembling】
Step 1 Power off the device.
Step 2 Hold the device steadily and screw out the screw in
the wall.
Step 3 Take out the device, disassembling ends.
Notice before power on:
Power ON operation: First insert the power supply
terminal block into the device power supply interface,
then plug the power supply plug contact and power on.
Power OFF operation: First, remove the power plug,
then remove the wiring section of terminal block. Please
pay attention to the above operation sequence.
【Power Supply Connection】
PoE power supply
The WAN port of this series device supports 48VDC PoE
power receiving, which conforms to IEEE802.3af/at standard.
12~48VDC power supply
This series device provides 1 DC power input
which is 3-pin 5.08mm pitch terminal block with
waterproof plug, the power supply supports
non-polarity. Power supply range: 12 ～48VDC. The pin
definitions of power supply are shown as follows:
Pin
1
2
3
Definition
V-
FG
V+
【Mounting SIM Card】
This series of device supports 1 Micro SIM card slot or 1 Nano
SIM card slot, provides 2 SIM card slots for redundant backup.
Notice:
If the SIM card needs to be changed, the device should
be power off first in case of damaging the card.
【Setting Reboot/ Restore Factory Setting Button】
This series device provides 1 reset button, press the
button for 1-2S then release it to reboot the device;
press the button for 5S then release it to restore
factory defaults.
【Checking LED Indicator】
This series device provides LED indicators to monitor the
device working status with a comprehensive simplified
troubleshooting; the detailed status of each LED is described
in the table as below:
LED
Indicate
Description
RUN
ON The device is powered on
or the
device is abnormal.
Blinking
The device is running normally
OFF
The device is powered off or the
device is abnormal.
WLAN
ON
Wireless WiFi network is enabled
Blinking
Wireless WiFi is in an active
network status
OFF Wireless WiFi network
is running
abnormally or turned off
5G
Blinking
5G module is operating normally
OFF
5G module isn’t operating
WAN
ON
WAN port has established valid
network connection
Blinking
WAN port is in network active
status
OFF
WAN port hasn't established valid

LED
Indicate
Description
network connection
LAN
ON
LAN port has established valid
network connection
Blinking
LAN port is in network active status
OFF LAN port hasn't established a valid
network connection
All indicators are off, which means
5G/4G signal at the opposite end is
weak or no signal
One indicator is on. It means 5G/4G
signal of the opposite end is weak
Two indicators are on, which
means 5G/4G signal at the
opposite end is normal
All indicators are on, which means
5G/4G signal at the opposite end is
strong
【Logging in to WEB Interface】
This series device supports WEB management and
configuration. Computer can access LAN port of the device
via Ethernet interface. The way of logging in to device’s
configuration interface via IE browser is shown as below:
Step 1 Configure the IP addresses of computer and the
device’s LAN port to the same network segment,
and the network between them can be mutually
accessed
Step 2 Enter device’s IP address in the address bar of the
computer browser.
Step 3 Enter device’s username and password in the login
window as shown below.
Step 4 Click “Login” button to login to the WEB interface of
the device.
Note:
The default IP address of the device’s LAN port is
“192.168.1.254”.
The default user name and password of the device are
“admin”.
If the user name or password is lost, user can restore it
to factory settings via restoring factory setting button;
all modified configurations will be cleared after
restoring to factory settings, so please backup
configuration file in advance.
Please refer to user manual for specific configuration
method of logging in to WEB interface and other
configurations about network management function.
【Specification】
Panel
WAN port
1 10/100/1000Base-
T(X) RJ45 port,
support PoE 48VDC
input power
supply
LAN port
1 10/100/1000Base-T(X) RJ45 port
Antenna
2 2.4G N-K type (Female) ports
2 5.8G N-K type (Female) ports
4 5G Sub-6G N-K type (Female)
ports
SIM card slot
1 Micro SIM card slot and 1 Nano SIM
card slot
Indicator
Running status
indicator, WLAN
indicator, 5G indicator, WLAN indicator,
LAN indicator, 5G signal strength
indicator
WiFi Transmission Rate
802.11n
6.5~300Mbps
802.11b
11/5.5/2/1Mbps
802.11g/a
54/48/36/24/18/12/9/6Mbps
802.11ac
65Mbps~867Mbps
WiFi Radio Frequency
Channel 802.11b/g/n:2.412GHz~2.4835GHz
802.11ac/n/a:5.18GHz-5.825GHz
RF power output
20dBm
Modulation
mode
DBPSK, DQPSK, CCK, OFDM,
16-QAM, 64-QAM
WiFi Receiving Sensitivity
802.11n_HT40
-82dBm@MCS0
、
-64dBm@MCS7
802.11n_HT20
-85dBm@MCS0
、
-67dBm@MCS7
802.11g/a
-91dBm@6Mbps
、
-72dBm@54Mbps
802.11b
-93dBm@1Mbps
、
-87dBm@11Mbps
802.11ac
-84dBm@MCS0
、
-59dBm@MCS9
WiFi Transmitting Power
802.11n_HT40
20dBm@MCS0
、
20dBm@MCS7
802.11n_HT20
20dBm@MCS0
、
20dBm@MCS7
802.11g/a
20dBm@6Mbps
、
20dBm@54Mbps
802.11b
20dBm@1Mbps
、
20dBm@11Mbps
802.11ac
20dBm@MCS0
、
20dBm@MCS9
5G Operating Frequency Band
Model I
5G NR:n78/n79/n41
4G
LTE:B1/B3/B5/B8/B34/B38/B39/B
40/B41

3G WCDMA:B1/B8
Model II
5G
NR:n1/n2/n3/n5/n7/n8/n12/n20/n2
8/n38/n40/n41/n48/n66/n71/n77/n

78/n79
4G
LTE-FDD:B1/B2/B3/B4/B5/B7/B8/
B9/B12/B13/B14/B17/B18/B19/B2
0/B25/B26/B28/B29/B30/B32/B66/
B71
4G
LTE-TDD:B34/B38/39/B40/B41/B4
2/B48
3G
WCDMA:B1/B2/B3/B4/B5/B6/B8/
B19
5G Bandwidth (downstream, upstream)
Model I
5G NR:DL 2Gbps; UL 230Mbps
（Theoretical rate）
LTE-TDD:DL 1Gbps;UL 30Mbps
LTE-FDD:DL 600Mbps;UL
75Mbps
3G（DC-HSPA+）:DL 42Mbps;UL
5.76Mbps
3G （HSPA+ ）:DL 21Mbps;UL
5.76Mbps
Model II
5G SA:DL 2.1Gbps;UL 900Mbps
5G NSA:DL 2.5Gbps;UL 650Mbps
LTE:DL 1Gbps;UL 200Mbps
WCDMA:DL 42Mbps;UL
5.76Mbps
Power Supply
Input power
supply
WAN port: supports PoE 48VDC
power receiving, which conforms
to IEEE802.3af/at standard

Power supply terminal:
12~48VDC, support non-polarity,
using 3-pin 5.08mm pitch terminal
with waterproof plug
Power Consumption
Model I
No-load: 5.8W
Full-load: 18.3W
Model II No-load: 5.5W
Full-load: 15.9W
Working Environment
Working
temperature
-40~75℃
Storage
temperature
-40~85℃
Working
humidity
5%～95%(no condensation)
Protection grade
IP68 (metal shell)