5th Axis V75150X VISE User manual

V75150X VISE
OWNER'S MANUAL

9: THUMBSCREW
P/N:TS10
ANTI-SIEZE
11: MOUNTING BOLT X2
M8x40
1
2X
2
2X
4
1X
6
1X
NOTE:
WARRANTY VOID
IF REMOVED
3
2X
5
2X
7
2X
8
8X
INCLUDED IN BOX
10: ANTI SIEZE
PACKET
P/N: LB8008C5-A
Page 2
ITEM
NO.
PART
NUMBER
DESCRIPTION QTY
1 SB3V SHOULDER BOLT 2
2 LP8 LOCATING PIN 2
3 M5X10.DP DOWEL PIN 5x10MM 2
4 V75150X-4RK LEADSCREW REPLACEMENT KIT 1
5 V75100X-2 TRUCK 2
6 V75150X-1 V75100X VISE BODY 1
7 V75100X-5 MASTER JAWS 2
8 76232 SHCS M8x16MM 8
9 TS10 THUMBSCREW 1
10 LB8008C5-A ANTI-SIEZE PACKET 1
11 76252 BOLT M8x40MM 2
BILL OF MATERIAL

SHIM
NO
YES YES
Maintenance and Use
Clean leadscrew with soft brush •
Use copper based anti-sieze on leadscrew (Loctite P/N: LB8008C5-A) •
Do not let chips build up during use •
Do not torque vise past 60 Nm [45 Ft LBS] •
Do not side load vise (see illustration below) •
Clamping Force at max torque with Master Jaws installed-22.2 kN [5000 lbf] •
Weight: 2.72 Kg [5.16 lbs] •
Torque Values
Jaw Bolts: 27 Nm [20 Ft LBS]-M8x16mm (P/N: 76232) •
Mounting Bolts: 34 Nm [25 Ft LBS]-M8x40mm (P/N: 76252) •
Lead Screw: 60 Nm [45 Ft LBS] Max •
Special Notes
Removing leadscrew assembly is not recommended and will void the •
warranty
Failure to follow these instructions will cause self centering accuracy and/or •
repeatability to fail and may cause damage to the vise
It is recomended to use only the two outside locating pin holes [LP8] labeled •
on page 4 as "A & B"
To Machine Profiles into Soft Jaws/Anti-Lift Soft Jaws:
Insert an appropriately sized shim between the jaws •
Torque to operating torque value •
Machine profile of part •
Remove shim and place the part in vise •
Torque to same value as previous •
Following these steps will ensure the highest accuracy
and will compensate for any jaw deflection
in the vise.
Page 3

158.00
6.220
35.00
1.378
12.00
.472
37.00
1.457
23.00
.906
2.50
.098
20.00
.787
45°
53.65
2.112
56.15
2.211
M5
8
52.00
2.047
100.00
3.937
150.00
5.906
75.00
2.953
4X
12.014
12.004
.4730
.4726
M8X1.25 FOR PS16F
3X
8.019
8.009
.3157
.3153
M5X.08 FOR LP8
B
A
DIMENSIONS
C
L
C
L
C
L
Page 4

0-90 mm
[0-3.5 in]
40-127 mm
[1.57-5 in]
Use Dovetail for:
Harder Materials •
Heavier Machining •
Parts Larger than the Vise •
Use Serrations For:
Softer Materials (Aluminum •
and soft steels)
Less Aggressive Machining •
CONFIGURATIONS
(See next page for dovetail stock prep)
Page 5

45.47
1.790
TO SHARP
B
DETAIL B
SCALE 2 : 1
[R .0381 mm]
R .015
45°
C
2.50
.098
R0.25
.010
1.38
.054
DETAIL C
SCALE 4 : 1
X
.085 .010
(2X/3)
TO SHARP
D
Gap
DETAIL D
SCALE 1 : 1.2
Contact
Contact
Master Jaws
Steel Grade: 4140 Steel
Hardness: HRC 53-57
P/N:V75100X-5
Dovetail Stock Prep
Dovetail Cutter
Page 6

Anti-Lift Soft Jaws
P/N: AL75XA (ALUMINUM), AL75XS (STEEL)
REPLACEMENT JAW P/N: AL75-2A (ALUMINUM), AL75-2S (STEEL)
WHAT IS INCLUDED
Anti-Lift Cleats
AL75 Anti-Lift Soft Jaws
Jaw Covers
Jaw Cover Hardware
Soft Jaws
VAJ75X- Aluminium
P/N: VAJ75X
6061-T6 •
Compatible with V75100 •
and V75100X
75mm x 45mm x 25mm •
DOWNLOAD DRAWINGS AT: FIFTHAXIS.COM/DOWNLOADS
Replacement Master Jaws
P/N: V75100X-5
P/N: V75100X-5 •
75mm x 37mm x 21mm •
Cutter Details
Shank Diameter (in) 1″ (P/N: DC1750-45) •
Shank Diameter (mm) 25mm (P/N: DC1750-M) •
Insert Part Number: DC1750-B •
45 Degrees •
Material H13 Tool Steel •
5 Flute Cutter •
Cutting Diameter: 45.5mm [1.79in] •
52mm Pull Studs
P/N: PS16-F
For 52mm Rocklock •
Hardened S7 Tool Steel •
M8 Threads •
VSJ75X-Steel
P/N: VSJ75X
1018 Annealed •
Compatible with V75100 •
and V75100X
75mm x 45mm x 25mm •
ACCESSORIES
BENEFITS
High Precision Op 2 •
Reduced Jaw Lift <.025mm •
(<.001 in)
Patent Pending •
Available in Aluminum •
and 1018 Steel
Installing Pull Studs
Secure threaded stud •
finger tight only
Grease precision •
surfaces
Torque to 10 Ft-lbs via •
bottom hex head
Page 7

Install Double Station
Assembly
Install Center
Jaw
Remove Self-Centering
Assembly
Remove Shoulder
Bolts
Ask your distributor about how to upgrade your
system to a double station
PARTS SOLD SEPERATELY
CONVERTING YOUR SELF CENTERING VISE
Reuse Your
Jaw Set
CONVERT YOUR CENTERING VISE TO A
DOUBLE STATION VISE
V75150X OWNER'S
MANUAL
REV A
APPROVED 5/15/2019
Available for download
at: fifthaxis.com/downloads
Soft Jaw and Master Jaw Compatible
Ask your distributor about how to upgrade your system to a double station
PARTS SOLD SEPERATELY