9dot SPMS SPI User manual

1
SPI & SPP MANUAL VER. 2 REV. 0
SPMS
I

2
SPI & SPP MANUAL VER. 2 REV. 0
Important notes .........................................................................................................................................................................3
Safety ..........................................................................................................................................................................................4
General warnings and precautions ............................................................................................................................................4
Certifications and compliances ..................................................................................................................................................4
Guarantee ...................................................................................................................................................................................4
General description ....................................................................................................................................................................5
SPI ...............................................................................................................................................................................................5
SPP ..............................................................................................................................................................................................7
Label ........................................................................................................................................................................................................... 8
Technical specifications .............................................................................................................................................................9
Installation ............................................................................................................................................................................... 11
Quick setup ....................................................................................................................................................................................................................................... 11
Physical interface ..................................................................................................................................................................... 12
LED coding ............................................................................................................................................................................................... 12
SPI..................................................................................................................................................................................................................................................... 12
Input power supply .................................................................................................................................................................. 12
Special case -48V ............................................................................................................................................................................................................................ 12
Official distributors .................................................................................................................................................................. 14

3
SPI & SPP MANUAL VER. 2 REV. 0
Important notes
 Warnings and cautions must be read and understood before installing 9dot products. Otherwise, personal injury could
occur.
 The photographs, diagrams and figures contained in this manual are for illustrative purposes only. They may not
match to your installation.
 9dot will not be liable for eventual damage or injury involving its hardware if it is used in any way inconsistent with
its intended purpose, or if it is installed or used in an untested manner or is improperly maintained.
 The material in this document is for informational purposes only and is subject to change without notice. While
reasonable efforts have been made in the preparation of this document to ensure its accuracy, 9dot assumes no
responsibility for errors or omissions in this document or for the use of the information contained therein. 9dot
reserves the right to make changes to the design of the product without reservation and without prior notice to its
users.
 The operator is advised to review the drawings and illustrations contained in this manual before proceeding. If you
have any questions regarding the safe operation of this power system, please contact 9dot or your nearest 9dot
distributor1.
 For more information, visit www.9dot.it
For technical support, please contact:
Email: supp[email protected]
1
See section "Official Distributors"

4
SPI & SPP MANUAL VER. 2 REV. 0
Safety
This manual contains important safety instructions that must be followed during installation, operation, and maintenance of
the product. Review the drawings and illustrations in this manual before proceeding. If you have any questions regarding the
safe installation or operation of this product, please contact 9dot or your nearest 9dot representative. Please keep it in a safe
place for future reference.
To reduce the risk of injury and to ensure continued safe operation of this product, the following terms have been incorporated
into this manual:
 ATTENTION: indicates safety information intended to prevent damage to people, materials or equipment
 IMPORTANT NOTE: additional clarifications on some features, terminology, reminders, etc.
Where they appear, please take more care and attention.
General warnings and precautions
You should read and understand the following warnings before installing the 9dot SPMS and its components. Otherwise, it
could cause personal injury.
• Read and follow all instructions included in this manual.
• Don't work alone in dangerous conditions.
• Only qualified personnel may install, use, and repair this system and its components.
• Always assume electrical connections or conductors are live. Turn off all switches and recheck connections with a
voltmeter before installation or maintenance.
• Keep the installation area clean and dust-free during and after installation.
• Wear safety glasses when working in conditions that can be dangerous to the eyes.
Certifications and compliances
The equipment has been tested in accordance with:
 RoHS directive
 European standard CE
 EMC standard EN 55022 Class B, EN61000-4
Guarantee
To know the guarantee of our products, consult with our nearest distributor. See the “Official Distributors” section of this
document.

5
SPI & SPP MANUAL VER. 2 REV. 0
General description
Smart Power Module System (SPMS) is a modular system for powering Power over Ethernet devices with different pin out.
Each module performs its function independently and guarantees maximum reliability and protection.
The products that make up this solution are:
• SPI: Surge Protector Injector
• SPP: Surge Protector Passthrough
SPI
Surge Protector Injector is a Power over Ethernet injector with integrated arresters, reverse polarity protection, redundant
power supply and selectable pin out and polarity.
Each SPI can be configured to handle a different type of PoE injection map. The configuration of the power pin out is simple
and does not require any computer skills: just select the mode and polarity with the microswitches on the side of the SPI
module.
On the back of the module is the grounding connector to protect people and equipment. For correct operation of the arresters
it is necessary to connect the GND earth terminal.
It allows to power all PoE systems with the operating modes: A, B, A + B.
Allows you to select the polarity between normal and reverse.
Figure 1 – SPI isometric view
6
7
4
2
5
3
1
1
GROUNDING
2
MODE SELECTOR
3
POLARITY SELECTOR
LI
/
~
II
irr
\
7
i
/
ir
^
\
A
/

6
SPI & SPP MANUAL VER. 2 REV. 0
On the front there is a LED that indicates if the device is active.
Gigabit port with PoE output to power different devices according to the chosen mode and polarity. The output voltage is the
same as the input voltage on the INPUT connectors.
Gigabit data port, galvanically isolated from the PoE port.
There are redundant power supply terminals.
4
LED INDICATORE
5
POE INJECTOR PORT
6
LAN PORT
7
POWER CONNECTOR

7
SPI & SPP MANUAL VER. 2 REV. 0
SPP
Surge Protector Passthrough is a passthrough surge arrester that can be plugged into a Power over Ethernet line to prevent
damage caused by surges. Just connect the two ports without making any changes to what is applied to the input, simply by
adding an arresters protection to the line.
Grounding connector to protect people and equipment. For correct operation of the arresters it is necessary to connect the
GND earth terminal.
Gigabit port to connect the device to be powered.
Data Gigabit + PoE port.
IMPORTANT NOTE: the silk-screen printing has been designed to provide a guideline for using the device. You can connect
the cables in another way while still obtaining overvoltage protection.
The device can also be used without PoE, just to protect a data line.
3
2
1
1
GROUNDING
3
“PROTECTED LAN” PORT
2
“POE DEVICE” PORT
Figure 2 – SPP module isometric view

8
SPI & SPP MANUAL VER. 2 REV. 0
Label
These devices come with a label attached with the relevant information, which we will describe below.
As we can see, the label shows:
• The product code: SPI / SPP, with its short description.
• The type of module and the serial number.
• Indications of power requirements.
• The part number P / N.
• Indications of compliance with CE and RoHS standards.
The image of the garbage container indicates that this equipment should not be placed in household containers. Instead, it
must be disposed of correctly in compliance with current regulations.
Figure 3 – label example of SPI and SPP
SPI
9
C
•
Passive
Surge
Protector
Injector
(
?
)
VRoHS
)
\
COMPLIANT
/
Module
Type
:
{
0
,
2
}
Serial
:
{
0
,
5
,
30
}
Input
voltage
:
10
-
60
V
AC
/
DC
Caution
:
For indoor
use
only
.
Can
cause
electric shock
.
Do
not
open
.
Made
in
Italy
-
P
/
N
:
00012012030100
-
9
DOT
Sri
-
www
.
9
dot
.
it
SPP
9
C
•
Passive
Surge
Protector
(
?
)
\
RoHS
I
\
COMPUANT
/
Module
Type
:
{
0
,
3
}
Serial
:
{
0
,
1
,
162
}
Input
voltage
:
10
-
60
V
AC
/
DC
Caution
:
For indoor
use
only
.
Can
cause
electric shock
.
Do
not
open
.
Made
in
Italy
-
P
/
N
:
00021902280100
-
9
DOT
Sri
-
www
.
9
dot
.
it

9
SPI & SPP MANUAL VER. 2 REV. 0
Technical specifications
SPI MODULE
Product code SPI
ELECTRICAL SPECIFICATIONS
Operating voltage [V] Clamps: +/- 10 to 60 AC/DC
Main power connector 2 x cable terminals 2 x 1.31 mm2
Active protection
Against
polarity inversion on both power connectors
Self
-
consumption power [W]
<
1.5
Typical current per port [A] (*) 0.7
GND connector Screw M4
LED indicator Status
Peak current protection [kA] 15
Overvoltage protection [V]
150
Protection mode All the lines (1-8) Protected (L-L) and (L-G)
SPD technology 2 phases: TVS and GDT
NETWORK SPECIFICATIONS
Ethernet connector 2 x Jack RJ45 shielded (LAN / PoE + Data)
Network transmission speed 10BaseT; 100BaseT; 1000BaseT
MECHANICAL SPECIFICATIONS
Dimension
s
(LxPxH) [mm]
8
7
x
8
4
x
24
(36
with flange
)
Weight [gr] 200
Material Varnished iron
Mounting On rack (with optional Rack bracket) or Din rail (with optional Din clip)
ENVIRONMENTAL SPECIFICATIONS
Operating ambient
temperature [° C]
-
20
to
+45
Operating humidity without condensation [%] 5 to 95
IMPORTANT NOTES:
• (*) Although the typical value indicates that 0.7A current can flow continuously and indefinitely, this value must not
be exceeded.
• (*) The typical current of 0.7A per port can be reached if the PoE configuration chosen to power a device is MODE A
+ B because it uses all four pairs of conductors for power supply2. If it is MODE A or MODE B, the typical current per
port will be 0.35A.
2
See the section “Selectors”

10
SPI & SPP MANUAL VER. 2 REV. 0
SPP
MODULE
Product code
SPP
ELECTRICAL SPECIFICATIONS
Operating voltage [V] Clamps: +/- 10 to 60 AC/DC
GND connector Screw M4
Typical current per port [A] (*) 3
Peak current protection [kA] 15
Overvoltage protection [V]
150
Protection mode All the lines (1-8) Protected (L-L) and (L-G)
SPD technology 2 phases: TVS and GDT
NETWORK SPECIFICATIONS
Ethernet connector
2 x
Jack RJ45
shielded (LAN / PoE + Data)
Network transmission speed
10BaseT; 100BaseT
; 1000BaseT
MECANICAL SPECIFICATIONS
Dimensions (LxPxH) [mm] 41 x 84 x 24 (36 with flange)
Weight [gr] 100
Material Varnished iron
Mounting On rack (with optional Rack bracket) or Din rail (with optional Din clip)
ENVIRONMENTAL SPECIFICATIONS
Operating ambient temperature [° C] -20 to +45
Operating humidity without condensation [%] 5 to 95
IMPORTANT NOTE: (*) Although the typical value indicates that 3A current can flow continuously and indefinitely, this value
must not be exceeded.

11
SPI & SPP MANUAL VER. 2 REV. 0
Installation
With the rack bracket it is possible to install up to 12 modules in an organized manner on a 2U rack.
Quick setup
Quick installation procedure below:
• (For SPI only) Configure the polarity and mode with the switches.
• (Optional) Insert the modules on the rack bracket or on the din bar.
• Wire the power supply (Optional standalone ACDC-48 or ACDC-24 power supplies provided separately by 9dot).
• Connect the power supply pins of the power supply to each module.
• (Optional) Insert the rack bracket in the structure used to house the devices.
• Connect the power supply to the electricity.
In addition, both SPIs and SPPs can be installed using the Din rail mounting clip.
Figure 5 - din bar Clip
Figure
4
-
black
rack
bracket
to
install
SPI
and
SPP
modules
in
19
"
rack

12
SPI & SPP MANUAL VER. 2 REV. 0
All these accessories are sold by 9dot and must be purchased separately. Below is the detail:
Product code (*) Description
Staffa Rack-B Standard 19" 2U rack adapter for max 12 CMD / ASPI / SPI / SPP. Black color
Clip-Din DIN Rail Clip for CMD/ASPI/SPI/SPP
ACDC-48 Power supply standalone AC/DC CONVERTER 48V 350W. Cables are not included
ACDC-24 Power supply standalone AC/DC CONVERTER 24V 350W Cables are not included
Table 1 - accessories supplied by 9dot
Physical interface
LED coding
SPI
To know the general status of the SPI, consider the LED on the front.
LED Color Description
Status Fixed blue turned on and working
Table 2 – SPI general status indication LED
Input power supply
The technical information is detailed below:
Module Input voltage Self-consumption Max load
SPI +/- 10 – 60V AC/DC < 1.5W 42W
SPP +/- 10 – 60V AC/DC n.a. 180W
Table 3 - range of voltage, self-consumption and maximum input load
IMPORTANT NOTES:
• In the case of two different power supplies (for example 48V and 24V), SPI will power the output device with the
highest active voltage. It is not possible to choose which voltage to power the devices in this case.
• No conversion is applied to the input voltage and there is no isolation between the power input and the PoE output.
• The PoE port and the LAN port are galvanically isolated from each other.
Special case -48V
The main input admits polarity inversion, that is, a negative voltage can be connected to its terminals without problems. The
redundant terminals can be used simultaneously, even with different voltages.
If you have a voltage of -48V (as is often the case in some telecommunication systems), simply connect the terminals in the
way you prefer.

13
SPI & SPP MANUAL VER. 2 REV. 0
SPI Output power supply
The main function of the PoE injector of this device is to allow the powering of other equipment on the network. SPI PoE
injector modules are passive injectors.
IMPORTANT NOTE: Unlike active PoE, passive PoE does not use any protocol to determine the type of device to be powered;
it simply applies a type of voltage to its port without identifying which type of PoE standard or supply voltage the connected
load is compatible with. Using an unsuitable voltage and / or wrong pin out can cause irreparable damage to the powered
device.
It is possible to power a wide range of devices that accept different voltages as this module essentially replicates the voltage
from the power terminals to the PoE output ports without applying any conversion.
This offers great versatility when it comes to connecting several PoE devices in the same infrastructure as each module can be
powered with a different voltage than the rest.
In addition to supporting different voltages, the SPI has the ability to select the pin out of the PoE output ports, with two
selectors placed on the side of the module, thus allowing it to power a wide range of devices on the market.
To find out if your PoE device can be powered by SPI, just check the pin out that the switches allow you to select and see if it
matches the input pin out of your equipment3.
Selectors
With the mode and polarity selectors of the SPI module it is possible to select the output pin out of the PoE port, according to
the following tables:
Modali
ty
Pins
MODE A+B
Po4P
MODE B 4,5 / 7,8
MODE A 1,2 / 3,6
Table 4 - SPI selectable mode types
Polari
ty
Pins
NORMALE + 4,5 and/or 1,2 | – 7,8 and/or 3,6
INVERSA – 4,5 and/or 1,2 | + 7,8 and/or 3,6
Table 5 - SPI selectable polarity types
Special case -48V
There are installations that require -48V mains power supply, this option is perfectly feasible with SPI. We simply have to
connect the -48V to the SPI input4 and then select the correct mode and polarity in order to get -48V on the PoE ports based
on the input pin out of the devices we want to connect.
Protection
On the PoE port there are double phase surge arresters TVS (Transient Voltage Suppression) and GDT (Gas Discharge Tube).
3
See the sections “Selectors”
4
As explained in the "Input power supply" section

14
SPI & SPP MANUAL VER. 2 REV. 0
Official distributors
EUROP
A
, ASIA
&
AFRICA
Telcomms Srl
Via Giuntini 25 int. 22
56023 Navacchio (PI), Italy
([phone]
[email protected]
www.telcomms.it
Skylinks Telecoms
Unit 31, Ramstown, Gorey Business Park, Co.
Wexford, Y25 HC67, Ireland
0402 21955
[email protected]
www.skylinkstelecoms.ie
VanCo
U Čokoládoven 9
143 00 Praha 12, Czech Republic
[phone]
[email protected]
www.vanco.cz
Wifidom
Offices
Calle Valencia 63
08015 Barcelona, Spain
Headquarters
Avenida de la Industria, 32 28108 Madrid,
Spain
Offices
([phone]
Headquarters
([phone]
[e-mail]
www.wifidom.com
Winncom Technologies Regional Presence
Ireland
Suite 144 The Capel Building Suite 5, Mary's
Abbey,
Dublin 7, Ireland
[phone]
[email protected]
www.winncom.com

15
SPI & SPP MANUAL VER. 2 REV. 0
USA
&
CANADA
Streakwave Wireless, Inc. Headquarters
840 Jury Ct, San Jose, CA 95112, USA
Utah sales and distribution
1420 S 4800 W Suite B, Salt Lake City, UT
84104, USA
Ohio sales and distribution
11777 Enterprise Dr, Cincinnati, OH 45241,
USA
[phone]
[email protected]
www.streakwave.com
Winncom Technologies World Headquarters
28900 Fountain Pkwy, Unit B Solon, Ohio
44139, USA
[phone]
[email protected]
www.winncom.com
LATINA AMERICA & THE CARIBBEAN
Winncom Technologies CALA
Offices
3840 W 104th Street, Unit 6, Hialeah, FL 33018, USA
440-519-2984 or 1-888-946-6266 EXT 146
Spanish and English
[email protected]
[e-mail]
www.winncom.com
Visit us on our website: www.9dot.it
9dot is a registered trademark of 9dot in the European Union. Copyright © 2020 9dot.
Due to continuous product development, 9dot reserves the right to change specifications without prior notice.
CENTRAL ASIA & AUSTRALIA
Winncom Technologies Regional Presence
Uzbekistan
35, 6th passage, A. Kahhar St., Tashkent
100025, Uzbekistan
[phone]
[phone]
For US callers: 1 [phone] office code
802, Operator: 309, Sales: 332/333
[e-mail]
www.winncom.uz
Streakwave Pty Ltd
Ground Floor - 470 St Kilda Road
MELBOURNE VIC 3004
[phone]
[e-mail]